Velleman CCTVPROM17 User manual

CCTVPROM17
CCTV PACK –DVR –4 IR CAMERAS –500 GB HARD DISK
CCTV-PACK –DVR –4 IR-CAMERA'S –HARDE SCHIJF 500 GB
PACK VIDEOSURVEILLANCE –DVR –4 CAMÉRAS IR –DISQUE DUR 500 GO
JUEGO DE VIGILANCIA –DVR –4 CÁMARAS IR –DISCO DURO 500 GB
CCTV-PACK –VIDEORECORDER –4 IR-KAMERAS –FESTPLATTE 500 GB
CONJUNTO CCTV DVR –4 CÂMARAS IR –DISCO RIGIDO 500 GB
ZESTAW MONITORINGOWY DVR –4 KAMERY IR –HD 500 GB
QUICK INSTALLATION GUIDE 3
KORTE HANDLEIDING 14
GUIDE D'INSTALLATION RAPIDE 26
GUÍA RÁPIDA 38
SCHNELLEINSTIEG 50
GUIA RÁPIDA PARA INSTALAÇÃO 62
SKRÓCONA INSTRUKCJA INSTALACJI 74

CCTVPROM17
V. 02 –28/08/2013 2 ©Velleman nv
EN
1
DC 12V input terminal
2
Video output connector
NL
1
DC 12V ingangsaansluiting
2
Video-uitgangsaansluiting
FR
1
Connexion d‟entrée CC 12V
2
Connexion de sortie vidéo
DE
1
DC 12V-Eingangsanschluss
2
Video-Ausgangsanschluss
ES
1
Conexión de entrada CC 12V
PT
1
Terminal de entrada DC 12V
PL
1
Wejście zasilania DC 12V
2
Conexión de salida de vídeo
2
Conector de saída de vídeo
2
Złącze wyjściowe wideo

CCTVPROM17
V. 02 –28/08/2013 3 ©Velleman nv
QUICK INSTALLATION GUIDE
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could
harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it
should be taken to a specialized company for recycling. This device should be returned to your
distributor or to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly before bringing this device into service. If
the device was damaged in transit, don't install or use it and contact your dealer.
Notes
This document is a Quick installation guide. For more detailed information, refer to the full user manual on
the included CD-ROM.
Product images are for illustrative purposes only. Due to constant product improvements the actual product
may differ from the images.
Package content
1 x DVR with built-in SATA connection: DVR8H2
4 x varifocal IR colour cameras: CAMCOLBUL30
4 x 20 m camera cables
1 x 19 V power supply
1 x high-efficiency DC-DC converter for DVR and cameras
hard disk (built in): HD500GB/S
remote control: DVRRC4.
2. Safety Instructions
Keep the device away from children and unauthorised users.
Risk of electroshock when opening the cover. Touching live wires can cause life-threatening
electroshocks. Have the device repaired by qualified personnel.
Always disconnect mains power when device not in use or when servicing or maintenance activities
are performed. Handle the power cord by the plug only.
3. General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
Indoor use only. Keep this device away from rain, moisture, splashing and dripping liquids.
Never put objects filled with liquids on top of or close to the device.
Keep this device away from dust and extreme temperatures. Make sure the ventilation
openings are clear at all times. For sufficient air circulation, leave at least 1" (± 2.5 cm) in front
of the openings.
Protect this device from shocks and abuse. Avoid brute force when operating the device.
Familiarise yourself with the functions of the device before actually using it.
All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to
the device is not covered by the warranty.
Only use the device for its intended purpose. Using the device in an unauthorised way will void the
warranty.
Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the
dealer will not accept responsibility for any ensuing defects or problems.

CCTVPROM17
V. 02 –28/08/2013 4 ©Velleman nv
Keep this manual for future reference.
DO NOT use this product to violate privacy laws or perform other illegal activities.
4. Overview
Refer to the illustrations on page 2 of this manual.
Front panel
LED
indicators
HDD is reading or recording.
DVR is powered on.
NAVIGATE
Press one of the four positions on the navigate button to move the cursor
up ( ), down ( ), left ( ) or right ( ).
In playback mode, press the buttons to play/pause ( ), stop ( ),
fast rewind ( ) or fast forward ( ).
In setting mode, press the up ( ) or down ( ) button to change the
setting in the menu.
MENU
Press MENU to enter the main menu.
ENTER
Press ENTER to confirm the setting.
LIST
Press to quickly search the recorded files by event lists: RECORD / MOTION / ALARM / TIME, or
select FULL to show all the event logs.
To quickly search the time you want, select QUICK SEARCH. For more details, refer to the full
user manual.
PLAY
Press to play the recorded video.
SLOW
In playback mode, press to play the recorded file slowly.
ZOOM
In live or playback mode, press to enlarge the image of the selected channel.
SEQ
Press to show all screens sequentially in full screen mode. Press again to quit.
Press to show the multiple channel display mode.
1 –8
Press a button to select the corresponding channel.
AUDIO
= SLOW + ZOOM
Press SLOW and ZOOM simultaneously to select live or playback audio.
P.T.Z.
= SEQ. +
Press SEQ. and simultaneously to enter or exit PTZ control mode.
USB port
(2x)
Connect a USB flash drive for video backup to the left USB port ( ); connect a USB mouse
to the right port ( ).
Note: Do not connect two USB mice or two USB flash drives simultaneously.
Note: For a list of compatible USB flash drives, please refer to the appendices in the full user
manual.
Rear panel
VIDEO IN
8 video input channels to connect 8 external video sources e.g. cameras
MONITOR
1 video output channel to connect the DVR to the main monitor (composite)
Note: You can use the MONITOR, HDMI, and VGA output ports simultaneously.
CALL
connector for monitor specific for sequence display
AUDIO IN
4 audio input channels to connect four external audio sources, e.g. from cameras with audio
AUDIO OUT
1 audio output to connect to an audio device, e.g. a speaker (mono)
LAN port
Connect the DVR to a local network by plugging a network cable into this port.
HDMI
Connect to the HDMI port of a monitor that supports HDMI video output.
Note: You can use the MONITOR, HDMI, and VGA output ports simultaneously.
VGA
Connect to the VGA port of a monitor that supports HDMI video output.
Note: You can use the MONITOR, HDMI, and VGA output ports simultaneously.

CCTVPROM17
V. 02 –28/08/2013 5 ©Velleman nv
Rear panel
PUSH VIDEO
Alarm In
Connect an alarm device for event notifications to your smart phone (push video). The
alarm input 1 corresponds with video input 1.
DC 19V
power supply input
power switch
5. Hardware Setup
Connecting a Video Monitor
Obtain a suitable monitor (not included) and connect it to the MONITOR, HDMI, or VGA video output port on the
back of the DVR.
Note: You can use the MONITOR, HDMI, and VGA output ports simultaneously.
Connecting the Power Supply
1. Plug the DC output connector of the included power adaptor into the 19 VDC power input at the back of the
DVR.
Caution: Only use the included adaptor.
2. Plug the included power cable into the adaptor input connector and plug the other end into the mains. Do
not switch the DVR on yet.
Connecting a Camera
1. Obtain up to 8 suitable cameras (not included). Each camera needs its own power supply.
2. Connect the video output of the camera to either video input at the back of the DVR. The number next to
the input connectors represents the channel number. Connector type is BNC.
Connecting Audio
1. The DVR supports four audio inputs. Connect the audio output of an audio source to an audio input of the
DVR. Make sure to connect the audio channel to the corresponding video channel. Connector type is BNC.
2. There is also an audio output connector. Connect an audio device, e.g. a speaker, to this connector when
desired. Connector type is BNC.
Connecting Local Area Network (LAN)
Connect the DVR to a local network by plugging a network cable into the LAN port at the back of the DVR.
Connector type is 8P8C (RJ45). Setup is done through the OSD.
Connecting a USB Mouse
Connect a USB mouse to the right USB input port ( ) of the front panel.
6. Preliminary Settings
Make sure the connected cameras are on and set the power switch at the rear of the device to the on position.
The device takes about 15 to 30 seconds to start up.
Menu Overview
1. Press the MENU button and enter the password to open the menu.
Note: The default admin password is “0000” (4 times zero).
2. Right-click anywhere on the screen to open the main menu. Right-click again to close.

CCTVPROM17
V. 02 –28/08/2013 6 ©Velleman nv
QUICK START
GENERAL –TIME SETUP
DATE SETUP
DATE INFO –DAYLIGHT
SYSTEM
TOOLS –SYSTEM INFO
EVENT
INFORMATION
QUICK SEARCH –EVENT SEARCH –HDD INFO –EVENT LOG
ADVANCED
CONFIG
CAMERA –DETECTION –ALERT –NETWORK –SNTP –DISPLAY –RECORD –
REMOTE
SCHEDULE
SETTING
RECORD –DETECTION
For more information, refer to the full user manual.
Date and Time Setting
Before operating your DVR, please set the date and time on your DVR first.
Note: DO NOT change the date or time of your DVR after the recording function is activated. Otherwise, the
recorded data will be disordered and you will not be able to find the recorded file from backup by time search.
If users change the date or time accidentally when the recording function is activated, it is recommended to
clear all HDD data, and start recording again.
Note: When using the DVR for the first time, leave it powered on for at least 48 hours continuously after the
date and time is set correctly. It prevents DVR time from resetting if the DVR power is disconnected. If the DVR
time resets after power disconnection (for example caused by a power outage), the internal battery may run
down. In that case, you have to replace the internal battery. Please refer to the appendices in the full user
manual for more information.
1. Press the MENU button and enter the admin password to open the menu.
2. Select the QUICK START menu item.
3. Use the NAVIGATION button to move to the TIME SETUP menu item. Select it to set date and time.
Password Setting
1. Press the MENU button and enter the password to open the menu.
2. Select the SYSTEM menu item.
3. Go to TOOLS. Select ADMIN PASSWORD (or OPERATOR PASSWORD) and press the ENTER button to set the
password.
Note: An operator can not access the main menu, only the quick menu bar (see below).
4. Press the cursor up ( ) or down ( ) button to select the value of the first number and press enter
to save and go to the next character, or use the mouse to select the desired value. Repeat this for all four
password numbers.
Note: The default admin password is “0000” (4 times zero).
Record Settings
1. Press the MENU button and enter the password to open the menu.
2. Select the QUICK START menu item.
3. Select the GENERAL menu item using the NAVIGATION button.
4. Set the image size, image quality, and images per second for recording.
Refer to the full user manual on the included CD-ROM for more details.
Audio Playback
Press the SLOW and ZOOM button simultaneously to select the desired audio channel or use the quick menu
bar (see further in this manual). The current audio channel is indicated in the status bar.
Switching Users
1. The DVR can be accessed as administrator ( ) or operator ( ), icons are indicated in the status bar.
2. To switch between users, click on the user icon ( or ) to lock the current session ( ).
3. Press on the key lock icon ( ) then enter the password of the desired profile.

CCTVPROM17
V. 02 –28/08/2013 7 ©Velleman nv
7. Operation
Display
The following image shows the screen layout.
A
system date and time
B
general system status
C
available HDD capacity
D
channel status
live audio from audio channel 1-4
(indicated in white)
playback audio from audio channel 1-4
(indicated in yellow)
audio channel unselected
timer recording on
digital zoom on (yellow) / off
USB mouse connected
LAN connected / internet connected / no network connection
USB flash drive connected
overwrite on (default)
key lock on
PTZ mode
sequence mode
motion mode
recording mode
alarm mode
administrator logged on
operator logged on
Note that actual screen icons might differ slightly from the ones shown above.
Quick Menu Bar
Note: Only available when USB mouse is connected.
Move the mouse pointer to the left of the screen to extend the quick menu bar and show the functions:
Open channel switch panel.
Show playback control panel.
Zoom-in mode (select desired channel first before entering zoom mode).
Select audio channel (live mode only live channels can be selected).
Enter PTZ mode and show PTZ control panel.
Recording
1. Check whether the camera(s) is (are) properly connected and a HDD is present inside the device.
2. If the auto-recording and pre-alarm functions are enabled, the device will start recording images.
oBy default, the recording icon ( ) is displayed.
oIf the motion or alarm detection is activated and a motion or alarm is detected, the motion ( ) resp.
alarm ( ) icon is displayed.

CCTVPROM17
V. 02 –28/08/2013 8 ©Velleman nv
oIf timer recording is enabled, the timer recording icon ( ) is displayed.
oBy default, the device is in HDD overwrite mode and the icon ( ) is displayed.
Playback
Make sure the control panel is not locked and press the PLAY button on the control panel or use the quick menu
bar to open the playback control panel:
A
progress bar
D
information bar
B
control bar
E
close
C
event search
Note: There must be at least 8192 images of recorded data for playback to work properly. If not, the device
will stop playback. For example, if the IPS is 30, the recording time should be at least 273 seconds
(8192 images / 30 IPS) for the playback to work properly.
Increase or decrease the playback speed using the fast forward ( ) and fast rewind ( ) buttons. Click
once to get 4x speed forward/backward, click twice to get 8x speed, etc. Maximum speed is 32x.
Press the pause button ( ) to pause playback.
Press the stop button ( ) to return to live monitoring.
Press the SLOW button once to get 1/4x speed playback, and click twice to get 1/8x speed playback.
Search
There are four ways to search recorded files: by record list, motion list, alarm list or by timer list.
1. To search an event, press the LIST button on the front panel (make sure the control panel is not locked).
An overview of the recorded file types (ALARM, MANUAL, MOTION, SYSTEM and FULL LIST) is shown.
2. Select the desired list and recording from the list.
3. Press ENTER to start playback.
Note: The recorded files can also be searched via the included Video Viewer software.
8. Push Video Configuration
8.1 Pin Connection
This DVR can send notifications to your mobile devices, such as iPhone, iPad, and Android mobile devices, if an
alarm event occurs (push video). However, only certain alarm-in pins support this function.
Push Video Alarm-In Terminal
A push video alarm-in terminal is provided on the DVR rear panel. Refer to the table below for the pin
connections that support push video and their corresponding video channels.
Alarm
Corresponding video channel
Alarm 1
CH1

CCTVPROM17
V. 02 –28/08/2013 9 ©Velleman nv
Alarm Sensor Connection
Connect the alarm sensor, such as magnetic contacts, to the push video alarm-in terminal on the DVR rear
panel.
8.2 Configuration
Before configuring push video, make sure that:
The DVR system is set up as described in Hardware Setup and Preliminary Settings.
The DVR is connected to internet.
You have installed the EagleEyes app on your iPhone, iPad, or Android mobile devices.
For details, please refer to Mobile Surveillance via EagleEyes.
To configure push video:
1. Right-click to show the main menu and select ADVANCED CONFIG > NOTIFY.
2. Set GUARD to ON.
3. Configure your alarm sensor type (normal open or normal closed).
Careful! You have to select the opposite type for push video to work correctly.
If your alarm sensor is N.C. (normal closed, alarm goes off when the contact opens), then select
ALARM N.O.
If your alarm sensor is N.O. (normal open, alarm goes off when the contact closes), then select
ALARM N.C.
ADVANCED CONFIG
CAMERA
PUSH VIDEO
PUSH MESSAGE
MESSAGE MAIL
VIDEO MAIL
DETECTION
GUARD
ON
ALERT
CH01
ALARM OFF / INTERNAL ALARM

CH1
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
EXIT
4. Open EagleEyes and add this DVR to the EagleEyes address book.
Note: For more information on EagleEyes operation, please visit www.eagleeyescctv.com.

CCTVPROM17
V. 02 –28/08/2013 10 ©Velleman nv
5. Enable push video.
6. Trigger the input alarm.
7. Receive an event notification and see video.
9. Mobile Surveillance via EagleEyes
EagleEyes is a powerful mobile surveillance program developed by AV TECH Corporation.
Note: For more operations details about EagleEyes, visit http://www.eagleeyescctv.com.
For any comment or question about this program, contact Velleman. Visit www.velleman.eu for contact details.
9.1 Prerequisite
Before installing EagleEyes on your mobile phone for remote surveillance, make sure you have checked the
following:
Your mobile platform is iPhone, iPad, BlackBerry, or Android.
You have subscribed to mobile internet services on your phone; the service is available for use on your
phone.
Note: You may be charged for internet access via wireless or 3G networks. For the internet access rates,
contact your local network operator or service provider.
You have noted down the IP address, port number, user name, and password used to access your network
camera via internet.
9.2 Downloading EagleEyes
1. Connect to www.eagleeyescctv.com from your mobile device.
Note: Do not download EagleEyes from your computer.
2. Select Products > Software > Mobile app to access the EagleEyes introduction page.
3. Select your platform (iOS, BlackBerry, or Android) and download the program you need.
Note: This DVR is compatible only with iPhone, iPad, BlackBerry, and Android mobile devices.
4. Follow the on-screen instructions for downloading.
When the download is completed, EagleEyes is installed automatically on your mobile device.
Note: For more information about the configuration of this program, read the related instructions on the
download page.