VeriFone MX 760 User manual

Secure PumpPAY
MX 760 Configuration Guide
Revision: B
Software Version 2.00.07

Secure PumpPAY MX 760 Configuration Guide
November 10, 2011
VeriFone®, Inc.
2099 Gateway Place
Suite 600
San Jose, CA 95110
Telephone: [phone]
http://www.verifone.com
Printed in the United States of America.
© 2011 by VeriFone, Inc.
No part of this publication covered by the copyrights herein may be reproduced or
copied in any form or by any means — graphic, electronic, or mechanical, including
photocopying, taping, or information storage and retrieval systems — without written
permission of the publisher.
The contents of this document and all features and specifications are subject to
change without notice. The information contained herein does not represent a
commitment on the part of VeriFone, Inc.
Publications are not stocked at the address given above. Requests for VeriFone
publications should be made to your VeriFone representative.
VeriFone, the VeriFone logo, and Ruby SuperSystem are registered trademarks of
VeriFone, Inc. Sapphire, Topaz, HPV-20, Ruby Manager, Everest, EASY ID, Electronic
Journal On-site, and Ruby Card are trademarks of VeriFone, Inc. in the U.S. and/or
other countries. All other trademarks or brand names are the properties of their
respective holders.

Secure PumpPAY MX 760 Configuration Guide Revision History
Software
Version. Rev. Date Description
1.00.00 A June 01, 2010 Initial documentation
release.
2.00.03 B November 10, 2011 Updated for new software
version, which provides
PAYMEDIA audio and video
support.

November 10, 2011 i
Contents
Configuring the Secure PumpPAY Software . . . . . . . . . . 1
Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Setting Up the MX 760 for Use on a LAN . . . . . . . . . . . . . . . . . 2
Entering System Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Setting the Terminal IP Address . . . . . . . . . . . . . . . . . . . . . . 4
Other System Mode Functions . . . . . . . . . . . . . . . . . . . . . . . 6
Entering Manager Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Debit Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
No Debit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Poll DCR Options Configuration . . . . . . . . . . . . . . . . . . . . . 13
Printer Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Idle Time Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Enabling/Disabling the Network Connection . . . . . . . . . . . . 21
Enabling/Disabling Broadcast. . . . . . . . . . . . . . . . . . . . . . . . 23
RFID Configuration (Not Available) . . . . . . . . . . . . . . . . . . 24
Audio Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Video Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Media Proxy Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . 30
Changing the Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
VVES Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Setting Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Displaying a Log File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Clearing Log and Poll Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Entering Manager Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Running Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Diagnostics MENU1 Tests . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Diagnostics MENU2 Tests . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Running the Demo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Entering Manager Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Running the Demo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Secure PumpPAY Retrofit Kit Configuration Guide
ii November 10, 2011
Configuring the Ruby or Sapphire System . . . . . . . . . . . . 63
Running Gemstall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Running Gemstall for Shell Sites . . . . . . . . . . . . . . . . . . . . . . . . 64
Enabling Debit on the Ruby . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Enabling Fueling Image Animation on the Ruby . . . . . . . . . . . . 65

November 10, 2011 1
1Configuring the Secure PumpPAY Software
This chapter describes how to configure Secure PumpPAY MX 760 terminal after the Retrofit Kit has
been installed.
Important:Before you begin, be sure the switch on the RS232/RS485 Converter (P/N 13976-01) is
set to 2W (2-wire). If the switch is not set correctly, DCR communications between
Secure PumpPAY and the Ruby will fail. Also, make sure the converter is connected to
the power port of the Ruby.
Using the Keypad
The keys you use to configure the MX 760 terminal are described in the following illustration.
Note: Press [*]on the keypad to move the cursor to the left. Press [#] on the keypad to move the
cursor to the right.
Scroll ahead
through
options.
ENTER. Select options
and accept numeric entries.
CLEAR.
Go back to
previous
menu.
Scroll back
through
options.
Enter
numeric
data.
CANCEL.
Reject or delete
entries.

Secure PumpPAY Retrofit Kit Configuration Guide
2November 10, 2011
Setting Up the MX 760 for Use on a LAN
Use the following procedure for setting up the MX 760 terminal for use on the network.
To set up the MX 760 terminal for use on the network, you must enter System Mode.
Note: Before entering System Mode and selecting the functions to perform, verify that the
MX 760 terminal has been installed as described in one of the Secure PumpPAY MX 760
Installation Guides. Make sure that the terminal is connected to a power source,
connected to the network, and is turned on.
Entering System Mode
Note: If no application has been installed on the MX 760 terminal, the terminal will
automatically start in System Mode on power up.
If an application is running on the MX 760, do the following to enter System Mode:
1. At the main welcome screen, press the [1], [5], and [9] keys simultaneously on the keypad and
release the keys immediately.
2. After a 10 – 20 second wait, the system will prompt for the System Mode password. Enter the
password on the keypad and press [ENTER]. The default System Mode password is 166831.
3. If the password is entered correctly, the System Mode main menu screen displays. (If the
password is entered incorrectly, the system restarts the application.)

Secure PumpPAY Retrofit Kit Configuration Guide
November 10, 2011 3
4. To navigate through the menu screens and select functions, use one of the following methods:
a. Use the menu keys as follows:
– Press the top, left menu key once to display a hand-shaped cursor. Press the key additional
times to move cursor over icons in a counter-clockwise (forward) direction. When the
cursor is over the function you want to select, press [ENTER].
– Press the top, right menu key once to display a hand-shaped cursor. Press the key
additional times to move cursor over icons in a clockwise (backward) direction. When the
cursor is over the function you want to select, press [ENTER].
b. Use the numeric keypad as follows:
– Press 1 to select Information.
– Press 2 to select Configure.
– Press 3 to select Diagnostics.
– Press 4 to select File Transfer.
– Press 5 to select File Manager.
– Press 6 to select Security.
– Press 7 to select the Left Arrow (if visible)
– Press 8 to navigate up (when applicable).
– Press 9 to select the Right Arrow (if visible).
– Press 0 to navigate down (when applicable).
–Press
*to move cursor counter-clockwise.
–Press
#to move cursor clockwise.
Press to Move
Forward Through
Menu
Press to Move
Backwards Through
Menu

Secure PumpPAY Retrofit Kit Configuration Guide
4November 10, 2011
Setting the Terminal IP Address
To set the IP address for the MX 760, do the following.
1. From the System Mode main menu, select the CONFIGURE icon to display the Configure
menu.
2. From the Configure menu, select the NETWORK icon to display the Network Interface
menu.
3. From the Network Interface menu, select the Ethernet round button, and then select the
Ethernet oval button to display the Ethernet Configuration menu.
Select

Secure PumpPAY Retrofit Kit Configuration Guide
November 10, 2011 5
4. From the Ethernet Configuration menu, select the STATIC round button, and then select the
Address oval button to enter the IP Address. (Note that you must enter all digits; for example,
2 would be entered as 002). After you have entered the IP Address, press [ENTER] to return
to the Ethernet Configuration menu.
5. From the Ethernet Configuration menu, select the Netmask oval button to enter the Netmask.
(Note that you must enter all digits; for example, 2 would be entered as 002). After you have
entered the Netmask, press [ENTER] to return to the Ethernet Configuration menu.
6. From the Ethernet Configuration menu, select the Back Arrow icon to return to the Network
Interface menu, and then select Apply to set the new IP Address.
Note: If you do not select Apply, the IP Address will not be set.
7. To return to the System Mode menu, select the Left Arrow twice.
8. After successful completion, exit System Mode by selecting FILE MANAGER and then RUN
APPLICATION.

Secure PumpPAY Retrofit Kit Configuration Guide
6November 10, 2011
Other System Mode Functions
System Mode on the MX 760 terminal has several functions. Some are used with Secure PumpPAY;
others are not.
INFORMATION
From the System Mode main menu, select INFORMATION to display information about the
software and hardware devices connected to the MX 760. From the System Information menu you can
select buttons to display the following: OS Details, Packages, Flash, Cable, COM3, and Ethernet.
CONFIGURE
■NETWORK—Configure the terminal IP Address as described in the previous section
■DISPLAY—Adjusts the brightness of the display screen.
– From the Configure (1) menu, select the Right Arrow to display the Configure (2) menu.
– Select the DISPLAY icon to display the Display Configuration screen. Select the
minus (–) button to darken or the plus (+) button to brighten. As you press [ENTER], the
display will become darker or lighter.
■All other configuration functions are not used.

Secure PumpPAY Retrofit Kit Configuration Guide
November 10, 2011 7
DIAGNOSTICS (Not Supported)
The Diagnostics function in System Mode is not supported. Diagnostic functions should be performed
only in Manager Mode.
FILE TRANSFER (Not Supported)
The File Transfer menu is not supported.
FILE MANAGER
You can use the following functions from the File Manager menu.
■RUN APPLICATION—Exits System Mode and starts the application without rebooting the
MX 760.
■RESTART—Reboots the terminal and starts the application if an application is loaded.
Otherwise, it will reboot the terminal and return to System Mode.
■EXPLORE FILES—Displays the files on the system.
■The remaining File Manager options are not supported.
SECURITY
The Security menu is not supported. Use Manager Mode to display debit key status and key type. The
Secure PumpPAY Installer is used to load key packages.
Entering Manager Mode
The MX 760 terminal has a Manager Mode to access the menus. You must enter Manager Mode each
time you want to configure the terminal or change the configuration.
Important:After you finish making configuration settings, you must exit all the way out of
Manager Mode to save the settings.
To access Manager Mode
1. At the main welcome screen, press the [#] key and [1] almost simultaneously, pressing the [#]
key first and then quickly pressing the [1] key. The following screen is displayed.
Address Mode
Clear to exit

Secure PumpPAY Retrofit Kit Configuration Guide
8November 10, 2011
2. Press the [#] key and [1] almost simultaneously again. If a password has been set, the
following screen is displayed. Note that this screen does not display the first time you enter
Manager Mode.
3. Enter the password and press [ENTER]. The screen displays the current settings. For
example:
Note that the ENC (encryption type), is viewed in System Mode.
Note that the IP address will show one of the following statuses (which may be truncated
depending on the length of the field):
–Enabled:Indicates that the Ethernet port is enabled.
– Disabled: Indicates that the Ethernet port is disabled.
–Error:Ignore this status. Not detrimental to the software.
The final two digits for the IP address must be in the range of 41 - 72 and must be incremented
for each MX 760 terminal at the site.
The MP IP is the address for the media proxy. The default address is 192.168.31.1.
Enter Password
DCR:02
Press ENT key
Mode: DEBIT SET
Printer: CUSTOM
ENC: (see IKSN)
Printer Speed: 115200
Min/Max poll: 10/1270
IP: 169.254.196.41 Ena
Ver: v20007 26 Oct 2011
MP IP 192.168.31.1

Secure PumpPAY Retrofit Kit Configuration Guide
November 10, 2011 9
4. Press the [ENTER] key again to display the following:
Debit Configuration
Use the following procedure to configure DUKPT debit on the MX 760.
Note: If debit payment is not allowed, go to the section “No Debit Configuration.”
1. Enter Manager Mode.
FUNCTION CONFIG
<-- ACCEPT -->
FUNCTION CONFIG
<-- ACCEPT -->

Secure PumpPAY Retrofit Kit Configuration Guide
10 November 10, 2011
2. Press [ENTER] to display the CONFIG menu.
3. Press [ENTER] to define what TYPE, or mode, of operation the debit/credit terminal will be
performing. Use the right scroll key to display the DEBIT option.
4. Press [ENTER] to define the card reader as a debit card reader. The following displays briefly
on the screen.
CONFIG TYPE
<-- ACCEPT -->
TYPE DEBIT
<-- ACCEPT -->
DEBIT TYPE SET

Secure PumpPAY Retrofit Kit Configuration Guide
November 10, 2011 11
5. Press [*] to display the following screen.
No Debit
Use the following procedure to configure the MX 760 to allow credit cards only. No encryption is
needed.
1. Enter Manager Mode.
2. Press [ENTER] to display the Debit/Credit CONFIG menu.
CONFIG TYPE
<-- ACCEPT -->
CONFIG TYPE
<-- ACCEPT -->

Secure PumpPAY Retrofit Kit Configuration Guide
12 November 10, 2011
3. Press [ENTER] to define what type, or mode, of operation the MX 760 terminal will be
performing.
4. Press the right scroll key to move forward through the options until NO DEBIT is displayed.
5. Press [ENTER] to accept the NO DEBIT option. A confirmation screen displays.
TYPE DEBIT
<-- ACCEPT -->
TYPE NO DEBIT
<-- ACCEPT -->
NO DEBIT SET

Secure PumpPAY Retrofit Kit Configuration Guide
November 10, 2011 13
6. Press [*]to return to the CONFIG menu.
Poll DCR Options Configuration
1. On the CONFIG screen, press the right scroll key until POLL DCR is displayed.
CONFIG TYPE
<-- ACCEPT -->
CONFIG POLL DCR
<-- ACCEPT -->

Secure PumpPAY Retrofit Kit Configuration Guide
14 November 10, 2011
2. Press [ENTER] to display the following screen. Then, press the numeric keys to specify the
fuel position, which must be a unique number. If the fuel position is 2, press [0] then [2].
3. Press [ENTER] to accept the fuel position and return to the CONFIG menu.
Printer Configuration
1. On the CONFIG screen, press the right scroll key until PRINTER is displayed.
DCR poll Adr: 02
Enter to Accept
CONFIG POLL DCR
<-- ACCEPT -->
CONFIG PRINTER
<-- ACCEPT -->