VistaLab Ovation 9060-1011 Guide

Multicha el Nozzle
Reco ditio i g Kit
Note: Wear gloves
1. Push the ejector slide in until it clicks
to fully expose the pipette’s nozzles.
2. Remove an existing seal y slipping
the end of a very small screwdriver or
tweezers under the edge of seal,
taking care not to score or scratch
nozzle surface. Stretch it up and over
the end of the nozzle.
3. Place a new seal on the countertop,
with the ri line closest to counter
surface.
4. Pick up the pipette and align the
nozzle with the new seal. Press down
to ease the seal over the end of the
nozzle and into place.
Proced re:
Nozzle Seal Replaceme t I structio s
L060-0100-001 Rev. B
2 Geneva Road
Brewster, NY 10509 USA
1-888-652-6520 • www.vistalab.co
The Nozzle Reconditioning Kit contains
complete nozzles and components that
can e replaced as needed.
Applicable Catalog Nu bers:
9060-1011
9060-2011
9060-3011
Package includes:
• 2 complete nozzle assem lies
• 24 replacement filters
• 24 replacement seals
• Filter insertion tool
• Tu ing
• Instructions
Note: Same nozzle filter is used for all models
When to replace Nozzles:
If a nozzle is leaking or does not aspirate, a complete nozzle can e replaced.
When to replace Nozzle Filters:
Nozzle filters are made of a cellulose material which prevents liquid from
entering the interior of the pipette. If the filter ecomes wet, the channel will
not aspirate or dispense until the filter is replaced.
When to replace Nozzle Seals:
Nozzle seals may need to e replaced when a channel leaks during pipetting,
or the seal is visi ly worn or torn.
1. Push the ejector slide in until it clicks to
fully expose the pipette’s nozzles.
(For 0.5-20µL models, see note on reverse)
2. Remove the affected nozzle(s) y placing
the ru er tu ing provided onto nozzle,
and unscrew it in a counterclockwise
direction.
3. Place ru er tu ing ack onto a new or
reconditioned nozzle, and screw the
nozzle onto the pipette in a clockwise
direction. Firmly tighten and remove
tu ing from nozzle.
Nozzle Replaceme t I structio s
Note: Wear gloves

Note: Wear gloves
1. Push the ejector slide in until it clicks
to fully expose the pipette’s nozzles.
(For 0.5-20µL models, see note on reverse)
2. Remove the affected nozzle(s) y
placing the ru er tu ing provided
onto nozzle, and unscrew it in a
counterclockwise direction.
3. Remove the filter inside the nozzle(s)
y inserting a straightened paperclip
into the small hole in the tip end of
the nozzle, and push the filter out
through the wide (threaded) opening.
4. Pick up a new nozzle filter with
tweezers and place it into the wide
(threaded) end of the nozzle.
NOTE: Make sure the narrow end is
inserted first
5. Use the filter insertion tool to push
the filter into position. Press down
until the end of the tool makes
contact with the inside ottom of the
nozzle.
Proced re:
Nozzle Filter Replaceme t I structio s
6. Tap the nozzle on the counter to
remove any loose cellulose material.
7. Place ru er tu ing ack onto the
nozzle, and screw the nozzle onto the
pipette in a clockwise direction. Firmly
tighten and remove tu ing from nozzle.
Special Note for 0.5–20µL Models:
To remove a nozzle(s) on 0.5–20µL
models, the rear panel of the ejector
sleeve needs to e removed.
Remove two screws on the panel, and
slide it away as shown. Remove springs
from posts, and remove affected nozzle(s)
with tu ing provided.
After filter(s) has een replaced, reinstall
springs, rear panel and screws.
2–125µL
0.5–20µL 5–250µL 25–850µL
Nozzle Reco ditio i g Kit 9060-1011 9060-2011 9060-3011
Contains 2 nozzles, 24 seals, 24 filters & tool
MU L T I C H A N N E L MO D E L
Applicable Nozzle Reconditioning Kits
9060-1011
Catalog Number