VistaLab Ovation M User manual

Operator’s Guide for
Mechanical Volume-Set Pipettes
(Ovation M)
L070-0001-001 Rev. B

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide
Product Description & Specifications 1-1
Pipette Components 1-2
Introduction & Ergonomics 2-1
Ovation pipetting 2-3
Picking Up & Holding 2-3
Selecting Liquid Handling Functions 2-3
Acquiring Tips 2-3
Aspirating and Dispensing 2-4
Ejecting Tips 2-4
Pipetting Hints for Optimal Performance 2-5
Introduction 3-1
Cleaning Exterior 4-1
Disinfecting Nozzles 4-1
Replacing a Nozzle 4-1
Replacing a Nozzle Filter 4-2
Plunger Assembly Seals 4-2
Autoclaving 4-2
Tips 5-1
Accessories 5-2
Warranty, Safety Compliance & Contact Information A-1
eneral Product Information A-2
TABLE OF CONTENTS
Introduction
BioNatural
ipetting
Calibration
Maintenance &
Troubleshooting
Tips & Accessories
Troubleshooting
Appendix A

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide 1 - 1
Ovation BioNatural™pipettes are the ideal ergonomic solution for liquid handling
tasks that contribute to repetitive stress injuries in today's laboratory. Ovation
pipettes increase laboratory efficiency through improved liquid handling routines,
while reducing fatigue and the effect of poor postures.
The Ovation M is intended for use as a liquid transfer device, capable of aspirating
and dispensing precise fluid volumes.
This manual describes how to use and care for your Ovation pipette. As you can see
from its appearance, it is different from every pipette that you have used before,
therefore please read the instructions carefully.
Six models of the Ovation pipette are available to cover liquid dispensing needs
ranging from 0.2µL to 1000µL.
Please activate the pipette’s warranty on the VistaLab Technologies web site –
www.vistalab.com. The required on-line form can be found in the “service” menu.
Retain all packing materials in the event that the pipette is to be sent back to VistaLab
Technologies for calibration verification or service.
roduct Description
Specifications
1
MECHANICAL VOLUME-SET I ETTES
Volume Dispensing
Range Increments
Model (µL) (µL) Accuracy recision
Ovation M 2µL 0.2 – 2 .002 ±1.5% t 2µL 0.9% t 2µL
(1070-0002) ±2.7% t 1µL 1.8% t 1µL
±9% t 0.2µL 7.6% t 0.2µL
Ovation M 10µL 1 – 10 .01 ±1% t 10µL 0.4% t 10µL
(1070-0010) ±1.5% t 5µL 0.6% t 5µL
±2.5% t 1µL 1.2% t 1µL
Ovation M 20µL 2 – 20 .02 ±1% t 20µL 0.3% t 20µL
(1070-0020) ±1.5% t 10µL 0.5% t 10µL
±7% t 2µL 2% t 2µL
Ovation M 100µL 10 – 100 .1 ±0.8% t 100µL 0.15% t 100µL
(1070-0100) ±0.8% t 50µL 0.24% t 50µL
±3.5% t 10µL 1% t 10µL
Ovation M 200µL 20 – 200 .2 ±0.8% t 200µL 0.15% t 200µL
(1070-0200) ±0.8% t 100µL 0.25% t 100µL
±2.5% t 20µL 1% t 20µL
Ovation M 1000µL 100 – 1000 1.0 ±0.8% t 1000µL 0.15% t 1000µL
(1070-1000) ±0.8% t 500µL 0.2% t 500µL
±3% t 100µL 0.6% t 100µL
Note: Perform nce d t is b sed on the use of Ov tion tips from Vist L b Technologies. If using
tips from nother m nuf cturer, the bove perform nce cl ims m y not be chieved.
Specific tions subject to ch nge. See www.vist l b.com for current inform tion.

Ejector Sleeve
Nozzle
Volume Di play Body
Tip Eject Button
Adju table
Hook
Plunger
Calibration Ring
Volume Label
Cap Opener
Serial Number
(under ide)
Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide 1 - 2
Description Function
Plu ger Initiates pipetting action and changes volume setting
Tip Eject Butto Ejects disposable pipette tips with minimal thumb force
Adjustable Hook Accommodates left and right handed users
Ejector Sleeve Stored energy from tip installation releases tips
Nozzle Tapered, chemically resistant coupling that secure pipette tips
Body Contoured grip surface for comfort, eliminating tight hand grip
Volume Label Identifies volume range
Calibratio Ri g Used to adjust pipette calibration
Cap Ope er Used to easily open PCR and microtubes
Serial Number Provides positive identification for the pipette
ipette Components

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide 2 - 1
2
BIONATURAL I ETTING
Studies have shown that pipetting is the #1 cause of musculoskeletal disorders in the
laboratory – it is, by nature, a repetitive process that puts strain on the body. While
we can’t change how repetitive pipetting is, we can and did change how comfortable
you are while doing it.
The Ovation BioNatural Pipette is the only pipette designed to keep your hand in the
neutral position recommended by ergonomics experts. We call this BioNatural™
pipetting – it allows a lower hand location to ease stress in the shoulder, and a
relaxed wrist angle eliminates uncomfortable extension and radial deviation
movements in the arm. Force, velocity and exertion from repetition or duration have
also been neutralized because of the Ovation pipette’s unique working position and
reduced forces required during operation.
Some practice may be required to change years of posture and habits developed
using standard axial pipettes; the physical benefits of BioNatural pipetting are worth
the practice! When using the Ovation pipette, arm/hand elevation should remain low
to the work surface, wrist rotation should not exceed 90º, and hand posture should
remain relaxed with the wrist and back of hand slightly flexed.
Introduction
osture
Arm elevation remains low,
minimizing stress to elbow,
shoulder and neck
A loose, relaxed grip increases
available strength in the hand,
improving endurance and
productivity during pipetting
Wrist remains in a neutral
range of motion throughout
all pipetting operations

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide 2 - 2
Ergonomics experts recommend establishing a “comfort zone” of
movement for the task of pipetting. Position your body within 9” of the
counter surface, and keep the items needed within easy reach. Ideally this
should be 14” or less, and should not exceed 24” of occasional reaching.
Wrist rotation should not exceed 90˚ from the work surface, and arm/hand
elevations should remain low to the counter surface.
Keep a “comfort zone”
for pipetting
14”
Maximum
Reach
“Comfort Zo e”
14”
24”
24”
5. Low arm and
elbow height
4. Neutral forearm
and wrist rotation
3. Relaxed hand grip
2. Low thumb forces
1. Relaxed shoulders
and upper arms
Ovation comfort-zone benefits:
1. Minimized tension and fatigue
2. Minimized exertion and contact stress
3. Low contact pressure
4. Lowest pressure in carpal tunnel and to median nerve
5. Minimized tension to shoulder and elbow

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide 2 - 3
The Ovation M has been designed to
allow the body of the pipette to fill your
palm. Rotate the adjustable
hook to rest
comfortably on your forefinger. The
texture of the unit’s back helps reinforce
correct hand positioning.
The unique ergonomic design and
adjustable hook is compatible for both
right and left-handed use.
Keep hand posture relaxed – there’s no
need for a “firm grip” when using an
Ovation pipette.
Changing the volume setting on the
Ovation M is easy. Simply rotate the
plunger to display the desired volume.
Turn clockwise to decrease the volume,
counter-clockwise to increase.
DO NOT rotate beyond the pipette’s
volume limits! This will damage the
pipette and void its warranty.
While maintaining a flat wrist-hand
posture, insert the Ovation pipette
nozzle into a tip. Press down until you
hear or feel a “click”. This “click”
indicates that the tip is properly seated
and ready for use.
Disposable pipette tips are to be used
once, then discarded. For proper fit and
to achieve stated precision and accuracy
specifications, use the VistaLab pipette
tips recommended in this manual. Use of
other manufacturer’s tips can cause the
pipette performance to differ from stated
specifications, can damage the nozzle or
ejector sleeve, or impede the performance
of the tip ejection system.
icking Up the
ipette
Changing
Volume Setting
Acquiring Tips

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide 2 - 4
1. Press the plunger down to the first
stop, and immerse pipette tip in the
sample.
2. Smoothly and slowly, release the
plunger allowing sample to enter the
pipette tip. Wait one second before
withdrawing the tip from the sample.
3. Place the pipette tip against the side
of the receiving vessel close to the
bottom of the vessel, or if it contains
liquid, just above the surface of the
liquid.
4. Smoothly depress the plunger to the
first stop. Wait one second, then fully
depress the plunger to the second
stop to dispense all liquid from the tip.
5. With the plunger depressed, slowly
withdraw the tip.
6. Release the plunger when the tip is
away from the receiving vessel.
If aspirating from PCR or microtubes,
the Ovation M has a built-in cap opener.
Simply insert the cap into the pipette’s
base.
Ovation pipettes store energy captured
during the acquisition of a tip, and use
it to discard tip when the tip eject button
is pressed. Point pipette tip into a
suitable waste container and press the
tip eject button to discard the tip.
To minimize forearm elevation and
“reaching”, position the waste container
below worksurface level or use shallow
containers. Raising the arm to discard
tips into a tall receptacle on the
counter may negate some of the
benefits of Ovation’s low-profile design.
Aspirating and
Dispensing
Ejecting Tips
Tip Immersion Depth
0.2µL to 10µL 1mm
11µL to 100µL 2-3mm
101µL to 1000µL 2-4mm

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide 2 - 5
• When using viscous or volatile reagents, pre-wetting the pipette tip may be
appropriate. To pre-wet, aspirate and dispense the liquid back into the original
vessel. Then fill the tip and dispense contents into receiving vessel.
• If an air bubble forms in the tip during aspiration, return the sample, discard the
tip, and use a fresh tip.
• Smoothly depress and release the plunger when pipetting, maintaining the same
speed of motion for all samples. Do not let the plunger “snap back” to the
uppermost position.
• When finished aspirating, touch the pipette tip against the side of the vessel as it
is being withdrawn to remove any liquid that may have adhered to the outside of
the tip. Wipe the pipette tip ONLY if there is liquid adhering to the outside. Be
careful not to “wick out” any of the contents from the pipette tip.
• Dispense against the side of the receiving vessel or above the liquid surface. To
remove any of the measured liquid that may have adhered to the pipette tip,
touch off the tip against the side of the receiving vessel.
•
Optional Type A nozzles for 100–1000µL models are designed to accommodate
some non-VistaLab tips.
• If aspirating from 15mL or 50mL centrifuge or other tall tubes, an optional Nozzle
Extender accessory is available which lengthens the pipette’s overall reach. If the
optional nozzle extender is being used, calibration verification should be checked.
ipetting Hints for
Optimal erformance
If the pipette is to be used with hazardous fluids, safe
laboratory practice is to be followed. Refer to manufacturer’s
Material Safety Data Sheets for proper handling instructions.
Always use VistaLab filtered tips (see tips table for catalog
numbers) when pipetting potentially caustic, corrosive or
volatile solutions. Failure to do so may result in premature
wear and damage to the internal seals and piston, and void
the pipette’s warranty.
When organic or volatile solutions are routinely used,
VistaLab Technologies recommends the use of VITON seals.
See the chemical compatibility chart in the Ovation
documentation library under “Resources” at
www.vistalab.com for more information.
Ovation pipette with Nozzle Extender

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide 3 - 1
3
CALIBRATION
Each Ovation pipette is factory calibrated to manufacturing specifications at 21.5˚C
(± 2˚) and relative humidity of 45%-75% using distilled wate r. It is recommended that
calibration be verified every six (6) months, when internal maintenance has been
performed, or on an as-needed basis.
The Ovation pipette can be easily in-lab calibrated ±10% for optimum performance at
your operating conditions. To determine volume delivery, VistaLab Technologies
recommends following the procedure “Ovation Performance Verification Protocol”.
This document is available at www.vistalab.com.
In-laboratory calibration can be accomplished by inserting the calibration key into the
calibration ring on the top of the Ovation pipette (see photo below). Volume delivery is
increased by turning the calibration ring in a counter-clockwise direction. Turning the
calibration ring in a clockwise direction decreases volume delivery. Each 1/4 turn
equals 1.7% of the pipette’s volume range. (example: on 100µL model, each 1/4
t rn adj sts the vol me 1.7µL)
It is recommended that whenever calibration is changed, the performance of the
pipette be verified.
Introduction
⤹
⤹
+
_

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide 4 - 1
The Ovation pipette requires minimal maintenance. Always store it in its “standing”
position or on the Ovation Pipette Stand (Catalog No. 9058-4003) when not in use.
Clean outer surfaces as needed with a soft cloth dampened with warm water. To
decontaminate outer surfaces, wipe with a 70% aqueous solution of ethanol or
isopropranol, or use a 10% bleach solution followed by water.
WARNING! Only wipe the volume display with water.
The replaceable nozzle contains an internal aerosol/liquid barrier filter to prevent liquid
from being aspirated into the pipette. Additionally, the nozzle filter offers protection to
internal parts from routine exposure to hazardous liquids and vapors. If this filter
becomes wet, the pipette will not aspirate fluid until a new nozzle is installed or the
nozzle filter is replaced.
Wipe the exterior surface of nozzles with disinfectant or a 10% bleach solution. Care
should be taken not to get the barrier filter inside the nozzle wet, as the pipette will
not aspirate and dispense properly until corrective action is taken.
If the pipette is not aspirating and dispensing properly, it could be caused by
(a) poor fitting alternate source tip, (b) nozzle is loose and needs to be tightened by
turning it clockwise, or (c) a nozzle or nozzle filter needs to be replaced as liquid
has been aspirated into it.
NOTE: Wear gloves when doing this procedure.
1. Remove ejector sleeve by pulling it away from the pipette body to expose the
nozzle assembly.
2. Place silicone tubing provided on nozzle, and unscrew nozzle in a counter-
clockwise direction. ently wipe the exposed end of the extension tube with a
slightly dampened, lint-free tissue, then dry it off.
Note: Do not block or dislodge anything at the end of the extension tube.
3. Place silicone tubing on a new nozzle, and screw the nozzle onto the extension
tube in a clockwise direction. Firmly tighten and remove silicone tubing.
4. Slide the ejector sleeve over the nozzle assembly.
5. Push the sleeve firmly into place while using a slight rocking or twisting motion.
Cleaning Exterior
Disinfecting Nozzles
Replacing a Nozzle
4
MAINTENANCE & TROUBLESHOOTING
Ejector Sleeve Nozzle
Exte sio Tube
Silico e Tubi g

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide 4 - 2
The internal aerosol/liquid barrier filter in the nozzle can be replaced as needed.
Refer to the Nozzle Filter replacement instructions on www.vistalab.com or in the
package with replacement nozzle filters.
VistaLab Technologies suggests that the Ovation Pipette’s seals be replaced
annually, or if any of the following symptoms are evident:
• Accuracy and precision claims cannot be achieved (not res lt of techniq e or method)
• The pipette does not aspirate or dispense (even after nozzle or filter has been replaced)
• The pipette leaks (when sing the recommended Ovation tips)
Repl cement Se ls:
9070-1001 Seal Kit for Ovation M 0.2-2µL
9070-1002 Seal Kit for Ovation M 1-10µL
9070-1003 Seal Kit for Ovation M 2-20µL
9070-1004 Seal Kit for Ovation M 10-100µL
9070-2005 Seal Kit for Ovation M 20-200µL
9070-3006 Seal Kit for Ovation M 100-1000µL
See the Support area of the VistaLab Technologies web site – www.vistalab.com –
for complete instructions about replacing plunger assembly seals. Information is
also available on the web site indicating the procedure for returning the pipette to
VistaLab Technologies for in-factory replacement of the plunger assembly seals.
Set the Ovation M to its highest volume setting and place it in the autoclave at
121˚C for 15 minutes, followed by a 15 minute drying cycle. Allow the pipette to
cool to room temperature for at least 2 hours before use. Calibration should be
verified after each autoclave treatment.
Note: The Ovation M nozzle should be replaced after 3 autoclave cycles as it will
lose its liquid blocking capability.
Replacing a Nozzle Filter
lunger Assembly Seals
Autoclaving

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide 5 - 1
5
TI S & ACCESSORIES
Whether your pplic tion requires tips th t re sterile, RN se/DN se certified, Pyrogen-free, Tr ce
Met l certified or filtered, there’s genuine Ov tion tip to meet your needs.
See the tip ch rt
(below) or visit our web site–www.vistalab.com for complete inform tion on
ll the tip options
for the Ov tion M Pipette, plus ccessories nd c libr tion nd rep ir services.
Example catalog number
4060-1002
VistaRak™
VistaStak™
Stacked Rack
0.2-2µL
Ovation M mechanical volume-set models: 1.0-10µL 10-100µL
2.0-20µL 20-200µL 100-1000µL
T I S I Z E : M I C R O S M A L L L A R G E
Notes: 1. Not for use with Ovation M .02-2µL .
N O N - S T E R I L ES T E R I L EF I L T E R E D
VistaRak
192 tips/rack, 5 racks 4060-1002 4060-2004 4060-3004
VistaRak, Low Retention
192 tips/rack, 5 racks
4070-1002LR 4070-2004LR 4070-3004LR
VistaStak, 192 tips/layer, 5 layers (small size)
or 3 layers (micro and large size) 4060-9024 4060-9025 4060-9026
Stacked Rack, 200 tips/layer,
5 layers (small size) or 3 layers (large size) 9025 9026
Stacked Rack, Trace Metal Certified, 200 tips/layer
5 layers (small size) or 3 layers (large size) 9022 9023
VistaBulk™, 1000 tips/ ag, or
250 tips/ ag (5mL) or 100 tips/ ag (10mL) 4058-1000 4058-2000 4058-3000
Protectainer™Bulk Pack,
1000 tips (small) or 750 tips (large) 4025 4026
Econo-Pak™Bulk Pack,
1000 tips 4225 4226
VistaRak, Sterile, Pyrogen-free,
RNase/DNase certified, 192 tips/rack, 5 racks 4060-1032 4060-2132 4060-3132
VistaRak, Sterile, Pyrogen-free, Low Retention,
RNase/DNase certified, 192 tips/rack, 5 racks
4070-1032LR 4070-2132LR 4070-3132LR
VistaTip™Individually Wrapped
Sterile, 200 tips
2025 2026
VistaTip Individually Wrapped, Sterile,
Pyrogen-free, 200 tips
2027 2028
VistaRak, Filtered, Sterile,
Pyrogen-free,
RNase/DNase certified,
192 tips/rack, 5 racks 4060-13321
4060-2332 4060-3332
†2µL tip for Ovation 0.2-2µL
4060-1333†
VistaRak, Filtered, Sterile, Pyrogen-free,
RNase/DNase certified,
192 tips/rack, 5 racks
4070-1332LR1
4 070-2332LR 4070-3332LR
192 tips/rack, 5 racks († 2µL tip for Ovation 0.2-2µL)
4070-1333LR†
Nozzle, 5/box (0.2–2µL) or 10/box 9057-1013†9057-2010 9057-3010
† for Ovation 0.2-20µL only
9057-1010
Nozzle Replacement Filters, 25/ba n/a 9057-2009 9057-3009
Type A Nozzle, 5/box n/a n/a 9057-1016
Nozzle Extender (except 0-2-2µL) 9057-1012 9057-3012
Ejector Sleeve 9057-1011 9057-3011
Calibration Labels, 5/box 9057-4002
Ovation Pipette Stand 9057-4003
A C C E S S O R I E S

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide 5 - 2
Maintenance & Repair Items for Ovation ipettes – Ovation M Models
Hook & Top Cover Kits
Catalog No. Description
9070-4008 Hook & Top Cover Kit for Ovation M models dispensing 0.2-2µL
9070-4009 Hook & Top Cover Kit for Ovation M models dispensing 1-10µL
9070-4010 Hook & Top Cover Kit for Ovation M models dispensing 2-20µL
9070-4011 Hook & Top Cover Kit for Ovation M models dispensing 10-100µL
9070-4012 Hook & Top Cover Kit for Ovation M models dispensing 20-200µL
9070-4013 Hook & Top Cover Kit for Ovation M models dispensing 100-1000µL
lunger Button Kits
Catalog No. Description
9070-4014 Plunger Button Kit for Ovation M models dispensing 0.2-2µL
9070-4015 Plunger Button Kit for Ovation M models dispensing 1-10µL
9070-4016 Plunger Button Kit for Ovation M models dispensing 2-20µL
9070-4017 Plunger Button Kit for Ovation M models dispensing 10-100µL
9070-4018 Plunger Button Kit for Ovation M models dispensing 20-200µL
9070-4019 Plunger Button Kit for Ovation M models dispensing 100-1000µL
Replacement Nozzles and Nozzle Filters
Catalog No. Description
9057-1013 Replacement Nozzles (Qty = 5) for Ovation M models dispensing 0.2-2µL
9057-1010 Replacement Nozzles (Qty = 10) for Ovation M models dispensing 1-10µL and 2-20µL
9057-2010 Replacement Nozzles (Qty = 10) for Ovation M models dispensing 10-100µL and 20-200µL
9057-3010 Replacement Nozzles (Qty = 10) for Ovation M models dispensing 100-1000µL
9057-3016 Replacement Type A Nozzles (Qty = 5) for Ovation M models dispensing 100-1000µL
9057-2009 Replacement Nozzle Filters (Qty = 25) for Ovation M models dispensing 10-100µL and 20-200µL
9057-3009 Replacement Nozzle Filters (Qty = 25) for Ovation M models dispensing 100-1000µL
Replacement Seal Kits
Catalog No. Description
9070-1001 Replacement Seal Kit for Ovation M models dispensing 0.2-2µL
9070-1002 Replacement Seal Kit for Ovation M models dispensing 1-10µL
9070-1003 Replacement Seal Kit for Ovation M models dispensing 2-20µL
9070-1004 Replacement Seal Kit for Ovation M models dispensing 10-100µL
9070-2005 Replacement Seal Kit for Ovation M models dispensing 20-200µL
9070-3006 Replacement Seal Kit for Ovation M models dispensing 100-1000µL
Miscellaneous
Catalog No. Description
9070-4020 Air Tube Cleaning Kit for all Ovation M models
9070-4006 Replacement Base Hex Screws for all Ovation M models
9070-4007 Calibration Tool for all Ovation M models

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide A - 1
A
A ENDIX
VistaLab Technologies, Inc. warrants the Ovation BioNatural Pipette against defects
in materials and workmanship for one year from the date of purchase. To register
your pipette and activate the warranty, register on the VistaLab Technologies web
site at www.vistalab.com.
This warranty is void if failure or damage is the result of improper handling,
unauthorized modification, or use of ancillary products not supported by VistaLab
Technologies. This warranty is exclusive; no other warranty is expressed or implied.
Should the pipette need to be returned for calibration verification or service, go to
support area of www.vistalab.com and follow the instructions for sending the
pipette to VistaLab Technologies. Repack the pipette in its original packaging.
Customer is responsible for shipping and insurance charges. If original packaging
is unavailable, contact VistaLab Technologies for alternative packaging instructions.
Note: Damage to the pipette as a result of improper packaging is the responsibility
of the customer.
Ovation pipettes have been tested and approved for safety labels:
EN 61010-1:1992 Safety Requirements CSA C22.2, No. 1010.1-92
EN 61326 EMC Requirements UL 3111-1
Note: Use of the Ovation pipette not specified in this manual may impair protection
provided by the equipment.
To place an order or to send in your pipette for factory maintenance and/or calibration
verification, see the service area of www.vistalab.com. Pipettes should be sent to:
VistaLab Technologies, Inc.
Attn: ipette Repair Department
2 Geneva Road
Brewster, NY 10509 USA
For additional assistance with warranty repairs or other technical assistance, contact
us at: 1-914-244-6226 (Worldwide) or [phone] (North America only), or
send an email to [email protected]
Warranty
Safety Compliance
Contact Information

Ovation BioNatural Pipette – Mechanical Volume-Set Operator’s uide A - 2
Operating Temperature & Environment Conditions
Indoor use / Pollution Degree 2
Altitude up to 2000m
Temperature Range: 15˚–35˚C
Relative Humidity Range, non-condensing: 10%–85%
Atmospheric Pressure: 70–106kPa
ipette Body Chemical Compatibility
Water, diluted ethanol or isopropanol, diluted bleach. For more information about chemical
compatibility with internal seals or pipette tips, see the documentation library in the support
area of our web site – www.vistalab.com.
General
roduct
Information