Volvo 30739998 User manual

Instruction No Version Part. No.
30739998 1.1
Cruise control
Instruction No Version Part. No.
30739998 1.1
Cruise control
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Cruise control- 30739998 - V1.1
Page 1 / 13

Equipment
A0000162 A0000161 A0801178
D8802049
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Cruise control- 30739998 - V1.1
Page 2 / 13

M8802108
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Cruise control- 30739998 - V1.1
Page 3 / 13

IMG-223164
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Cruise control- 30739998 - V1.1
Page 4 / 13

IMG-213320
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Cruise control- 30739998 - V1.1
Page 5 / 13

INTRODUCTION
Read through all of the instructions before starting installation.
Notifications and warning texts are for your safety and to
minimise the risk of something breaking during installation.
Ensure that all tools stated in the instructions are available
before starting installation.
Certain steps in the instructions are only presented in the form
of images. Explanatory text is also given for more complicated
steps.
In the event of any problems with the instructions or the
accessory, contact your local Volvo dealer.
Note!
This accessory requires software unique to the car.
1
IMG-237320
Turn the ignition key to position I to release the steering wheel
lock.
Disconnect the battery negative lead.
Note!
The SRS system remains active for a brief period after power
is cut off. Thus, wait 3 minutes before starting work.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Cruise control- 30739998 - V1.1
Page 6 / 13

2
IMG-217441
Turn the steering wheel a quarter turn so that the holes on the
reverse of the steering wheel are accessible.
3
IMG-217560
Insert a screwdriver in the hole (2) on the reverse of the steering
wheel, at right angles to the rear surface of the steering wheel.
Insert the screwdriver as far as possible to determine the
position of the end of the spring clip (1).
Position the end of the screwdriver on the top of the spring clip
as illustrated.
Pry the screwdriver upwards towards the upper edge of the hole
(2) so that the end of the screwdriver presses the spring clip
down (1) until one side of the steering wheel module springs out
and releases from the mounting.
Turn the steering wheel a half turn in the opposite direction.
Carry out the same operation on the other side.
Turn the steering wheel to a neutral position.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Cruise control- 30739998 - V1.1
Page 7 / 13

4
IMG-217442
Fold the steering wheel module out.
Remove the two connectors (1) for the ignition cables for the
airbag. First press in the catches on the sides. Then pull the
connectors straight out.
Note!
The connectors are tightly secured. However, tools must not
be used when removing.
Place the steering wheel module to one side.
Warning!
Position the steering wheel module with the front upwards in a
secure position while carrying out the work.
5
IMG-217520
Applies to vehicles without pre-drawn wiring harness
Remove the left and right keypad dummy from the steering
wheel by carefully prying it off using a plastic weatherstrip tool.
Twist the weatherstrip tool to pry them out. They are firmly held
in place by three lugs in the steering wheel, so some force is
required to remove them.
Unplug the connector and put the left keypad dummy aside. It
will not be reinstalled.
Applies to vehicles with pre-drawn wiring harness
Remove the left keypad/keypad dummy as described above. Put
it aside. It will not be reinstalled.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Cruise control- 30739998 - V1.1
Page 8 / 13

6
IMG-222884
Applies to vehicles with pre-drawn wiring harness
Take the new keypad from the kit. Plug in the connector and
press the keypad into the steering wheel.
7
IMG-222885
Applies to vehicles without pre-drawn wiring harness
Remove the three screws (1) and pull out the horn ring slightly
so that the connector (2) can be unplugged.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Cruise control- 30739998 - V1.1
Page 9 / 13

8
IMG-222886
Detach the ground cable (1) and connector (2) and remove the
signal ring from the steering wheel. Put it aside.
9
IMG-222886
Take the new signal ring from the kit and check that the three
springs on its underside are in place.
Connect the ground cable (1) and connector (2).
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Cruise control- 30739998 - V1.1
Page 10 / 13

10
IMG-222888
Insert the ignition cables in the holder (1).
Position the horn ring in the steering wheel.
Install the three screws (2) in the horn ring. Tighten the screws
to 8±2 Nm (6 ±1.5 lbf.ft.) in a crisscross pattern.
Note!
The screws are self tapping which may mean that it is difficult
to screw in.
Check the function of the horn by press the horn around its
entire circumference. A metallic noise should be heard when the
three contact points come into contact.
11
IMG-222920
Plug in the connector for the keypad/keypad dummy on the right
and left side and press them into the steering wheel.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Cruise control- 30739998 - V1.1
Page 11 / 13

12
IMG-217522
Check that the two springs (1) are in position.
Check that the ignition cables are correctly positioned in the
holder (2).
Press the two connectors for the ignition cables for the airbag
into the steering wheel module.
Insert the two pins on the reverse of the steering wheel module
in the two springs. Ensure that the ignition cables are not
trapped
Press the steering wheel module into the mountings. (Two clicks
should be heard).
13
IMG-236182
Installing the negative lead after working with SRS
components
Warning!
Make sure that no one is in the vehicle when this is done.
Activate the SRS system as described in "VIDA Vehicle
communication, SRS, powering the SRS system" before turning
the ignition key.
Initiating the windows
Initiate window position as described in "VIDA Vehicle
communication, Initiating window position".
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Cruise control- 30739998 - V1.1
Page 12 / 13

14
A0801178
Programme the software in accordance with the service
information in VIDA.
Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden
© Volvo Car Corporation Cruise control- 30739998 - V1.1
Page 13 / 13