WAREMA 4M230.12 2Down REG User manual

Valid from 1 April 2019
2029825_0•en
Manual
Sun shading actuator
KNX Actuator 4M230.12 2Down

2029825_0•en•2019-04-01
We reserve the right to make technical modifications
2
KNX -Actuator
4M230.12 2Down REG
General information
The publication of this document supersedes all previous corresponding doc-
umentation. We reserve the right to make changes in the interest of technical
progress. Particular care was taken in producing the text and graphics in this
documentation. In spite of this, we cannot accept liability for any existing er-
rors or the consequences thereof.
Legal information
Operating instructions, manuals and software are protected by copyright.
WAREMA and the WAREMA logo are registered trademarks of WAREMA
Renkhoff SE.
All other brand or product names included in this document are registered
trademarks of their respective owners.
Contact
Customer Centre Control Systems
Sales, order acceptance and applied engineering
Tel. [phone] • Fax -3759
[e-mail]
International
Tel. [phone] • Fax -3749
steuerungssyst[email protected]
Control Systems Helpline
Tel. [phone] • Fax -6769
ser[email protected]
Building automation systems sales
Dillberg 33, 97828 Marktheidenfeld
Tel. [phone] • Fax -3719
© 2019, WAREMA Renkhoff SE

2029825_0•en•2019-04-01 We reserve the right to make technical modifications 3
Contents
1 Description ....................................................................................................... 5
1.1 Technical data .......................................................................................................6
2 Installation and commissioning ..................................................................... 7
2.1 Information on installation ...................................................................................7
2.2 Information on installation and commissioning...............................................7
2.3 Instructions for use...............................................................................................8
2.4 Maintenance...........................................................................................................8
2.5 Connection.............................................................................................................9
2.6 Device structure ....................................................................................................9
2.7 Display of operating status through power LED .......................................... 10
2.8 Display of operating status through channel LED....................................... 10
2.9 Connection example ......................................................................................... 11
3 Transmission protocol................................................................................... 12
3.1 List of all group objects.................................................................................... 12
4 Adjustment of parameters............................................................................. 30
4.1 General settings ................................................................................................. 30
4.1.1 Local operation ............................................................................................ 30
4.2 Inputs.................................................................................................................... 31
4.2.1 Input as bus button ..................................................................................... 32
4.3 Outputs ................................................................................................................ 35
4.3.1 Channel settings - Blinds .......................................................................... 35
4.3.1.1 Control..................................................................................................... 36
4.3.1.2 Barriers.................................................................................................... 40
4.3.1.3 External control mode .......................................................................... 43
4.3.1.4 Internal control mode............................................................................ 44
4.3.1.5 Scenes..................................................................................................... 49
4.3.1.6 Push button inputs ................................................................................ 49
5 General section .............................................................................................. 51
5.1 Control modes for drive control ...................................................................... 51
5.2 Connection possibilities for zero position sensors...................................... 53
Table of contents

2029825_0•en•2019-04-01
We reserve the right to make technical modifications
4
Contents KNX Actuator
4M230.12 2Down REG

2029825_0•en•2019-04-01 We reserve the right to make technical modifications 5
1 Description
The KNX Actuator 4M230.12 2Down REG is an electronic control device
for the control of 4 motors with 3 limit switches (2 lower limit switches).
230VAC is required for the power supply to the actuators and the
drives.
The connected drives can be directly operated on the actuator and via con-
nected push buttons.
The control mode can be specified externally or internally. Internally there are
numerous possibilities for barriers, interlocks (e.g. master-slave) and priority
determinations (e.g. manual–control mode). Scenes can be saved and re-
trieved via the bus (scene control with 16 scenes per drive).
Binary inputs can either be used for direct operation (e.g. push button) or as
bus push buttons (or also for alarm messages, for example). The required
behaviour can be determined exactly by selecting the reaction times in stand-
ard, comfort or dead man's mode.
Description

2029825_0•en•2019-04-01
We reserve the right to make technical modifications
6
KNX -Actuator
4M230.12 2Down REG
Functions:
4 outputs for one drive each with 3 limit switches (2 lower limit switches)
Keypad with 4 push button pairs and status LEDs
12 binary inputs for use as manual or as bus push buttons
Position feedback on moving position
Position memory (moving position) via 1 bit object (storage and retrieval via
push button, for example)
Control through internal or external control mode
Integrated shading control for any drive output
Scene control for moving position with 16 scenes per drive
Safety objects of different priority with cyclical monitoring
Activation or deactivation of the automatic inputs (for example sun control,
slat tracking) with parameterizable control mode return function
The device is configured using the KNX software ETS (Engineering Tool Soft-
ware). The product database required for this (.knxprod) can be found in the
online catalogue of the ETS or on the Internet at http://www.warema.de/knx.
Scope of delivery
Actuator
1.1 Technical data
Housing Plastic
Colour White
Installation Series installation on DIN rail
Degree of protection IP 20
Dimensions approx. 107 × 88 × 60 (W × H × D mm), 6 MW
Total weight approx. 340 g
Ambient temperature Operation -20…+70°C, bearing -30…+70°C
Surrounding air humidity max. 95%RH, avoid condensation
Operating voltage 230 V AC, 50 Hz
Power consumption Operation max. approx. 3.5 W
Current On bus: 10 mA
Outputs
4 x drives with 2 bottom lower limit switches (UP/
DOWN1/DOWN2/N/PE), in total max. 10 A and max.
4A per output
Max. line length
Binary inputs 50 m
Data output KNX +/- bus plug terminal
BCU type Own microcontrollers
PEI type 0
Group addresses max. 1024
Allocations max. 1024
Group objects 757
Article number 2029566
The product conforms with the regulations of the EU directives.
Functions

2029825_0•en•2019-04-01 We reserve the right to make technical modifications 7
2 Installation and commissioning
2.1 Information on installation
WARNING
Only certified electricians (according to VDE0100) may install, examine,
commission and troubleshoot the device.
CAUTION
Electrical voltage!
There are unprotected live components inside the device.
Comply with the VDE regulations.
Connect all lines in a de-energised state and take safety precautions against
accidental switch-on.
Do not commission the device if it is damaged.
Deactivate the device or unit and secure against accidental operation if
hazard-free operation cannot be guaranteed.
The device is intended for proper use only. All warranties expire if the device
is subjected to any improper adjustment or if the operating instructions are
not complied with.
 The device must be inspected for potential mechanical damage immediately
after being unpacked. If damage has taken place during transport, the suppli-
er must be notified of this immediately.
 The device may only be used as a fixed installation, i.e. only when fully as-
sembled, after all installation and commissioning procedures are completed,
and only in the intended surroundings.
WAREMA Renkhoff SE cannot be held liable for any changes to the norms
and standards after publication of the operating instructions.
2.2 Information on installation and commissioning
 Never expose the device to water (rain). This can damage the electronics.
The relative humidity may not exceed 95%. Avoid condensation.
After the bus voltage is applied, the device performs an initialising phase
lasting a few seconds. No information can be received or sent by the bus
during this time.
 In the case of KNX devices with safety functions (for example a wind or rain
barrier), cyclical monitoring of the safety objects must be set up.
Technical data

2029825_0•en•2019-04-01
We reserve the right to make technical modifications
8
KNX -Actuator
4M230.12 2Down REG
2.3 Instructions for use
WARNING
Risk of injury due to automatically moved components!
The automatic control may cause system parts to start up and put people
in danger.
• Keep movement range of drives/curtains clear.
• Ensure that the return path/access is not blocked when outside the
building (risk of being locked out).
• Put unit properly out of operation during maintenance and cleaning
work.
NOTICE The system cannot function if the power fails. For this reason, shading should
for example be moved into a safe position in good time when bad weather
conditions are pending, unless this has already been carried out due to the
control function (product protection).
NOTICE If the 230VAC operating voltage fails, the connected drive is switched off. If
the operating voltage returns, the consumer remains switched off until a new
move command is received from the actuator.
2.4 Maintenance
The device must be regularly examined for proper function. There are no
parts inside the device requiring maintenance.
Installation / commissioning

2029825_0•en•2019-04-01 We reserve the right to make technical modifications 9
2.5 Connection
The device is suitable for operation in dry interiors. Connection in accord-
ance with the wiring diagram. Access to the drive for maintenance purposes
must be guaranteed at all times.
CAUTION
During installation and line routing on the KNX connection and the inputs,
observe the regulations and standards applicable for SELV power circuits!
The connections of the binary inputs including the auxiliary voltage
output comply with the requirements for SELV power circuits. A mixed
installation with non-SELV circuits or the mixing of different auxiliary
voltages is not permitted
2.6 Device structure
WAREMA KNX Aktor 4M230.12 2Tief REG
①②
③④
⑥
⑦
⑧⑨ ⑩ ⑪ ⑫
⑤
Fig. 1 View with frame and support plate
① Output 12 V GND
② Internal auxiliary voltage 12 V DC, only for binary inputs
③ Binary inputs 1-12 (1 to 4: per 2 connections)
④ Programming LED and programming button (PRG)
⑤ Slot, bus terminal (KNX+/-)
⑥ Power LED (mains), for display of operating status see Chapter below
⑦Push button pairs Up/Down and LEDs channels A-D, for meaning of LEDs
see Chapter below
⑧ Input operating voltage 230 V AC L/N/PE
⑨ Output A: UP-DOWN1-DOWN2, max. 4 A
⑩ Output B: UP-DOWN1-DOWN2, max. 4 A
⑪ Output C: UP-DOWN1-DOWN2, max. 4 A
⑫ Output D: UP-DOWN1-DOWN2, max. 4 A
⑨-⑫ together max. 10 A!
A mixture of different auxiliary voltages for the binary inputs is not permitted
Installation / commissioning

2029825_0•en•2019-04-01
We reserve the right to make technical modifications
10
KNX -Actuator
4M230.12 2Down REG
2.7 Display of operating status through power LED
Behaviour Colour
On Green Normal operation.
Bus connection/bus voltage available.
Flashes Green Normal operation.
No bus connection/bus voltage available.
On Orange Device starts or is programmed via the ETS.
No control functions are executed.
Flashes
Green (on)
Orange (flash-
es)
Programming mode active.
2.8 Display of operating status through channel LED
On Top Drive in upper limit position.
On Bottom Drive in lower limit position.
Flashes
slowly Top Drive moving upwards.
Flashes
slowly Bottom Drive moving downwards.
Flashes fast Top Drive in upper limit position, barrier active.
Flashes fast Bottom Drive in lower limit position (AB2), barrier active.
Flashes fast Both at the
same time Drive in intermediate position, barrier active.
Off Both Drive in intermediate position.
"Running
light" across
all LEDs
All channels The wrong application version has been loaded.
Use the version appropriate for the device.
Installation / commissioning

2029825_0•en•2019-04-01 We reserve the right to make technical modifications 11
2.9 Connection example
L
N
PE
connecting line
230 V AC,
50/60 Hz, 16 A,
3 x 1.5 mm2
1 2 3 N PE
MA
230 V AC
Motor B, C and D
accordingly
to output B, C and D
Up
Up
Down
Down
[[ [[
push button for
motor A
e.g.
central button
KNX- KNX+
-
+-
+
WAREMA KNX Aktor 4M230.12 2Tief REG
Attention:
Only one motor can be connected
per motor terminal set.
If interconnected, the motor will
be damaged.
Motor lines for motors with 2 lower limit switches
H05-RR-F 5 G 0.75 bk
The following applies for Switzerland:
H05-RR-F 5 G 1.5 bk
or alternatively
LiHH 5x1.5 JZ gy 600/1000V flexible, halogen-free
(not UV-resistant)
All bus lines
YCYM 2×2×0.8mm
KNX BusKNX Bus
Fig. 2 Connection example KNX Actuator 4M230.12 2Down REG
Installation / commissioning

2029825_0•en•2019-04-01
We reserve the right to make technical modifications
12
KNX -Actuator
4M230.12 2Down REG
3 Transmission protocol
3.1 List of all group objects
Flag abbreviations:
K Communication
L Read
S Write
Ü Transmit
A Update
No. Text Function Flags DPT type Size
1 Software version Readable L-K- [217.1] DPT_Version 2 bytes
50 Input 1 - Long-term Input/out-
put
LSKÜ [1.8] DPT_UpDown 1 bit
51 Input 1 - Short-term Input L-KÜ [1.8] DPT_UpDown 1 bit
52 Input 1 - Switching Input LSKÜ [1.1] DPT_Switch 1 bit
53 Input 1 - Dimming
relative
Input LSKÜ [3.7] DPT_Control_
Dimming
4 byte
54 Input 1 - 8 bit sensor Input L-KÜ [5] 5.xxx 1 byte
55 Input 1 - Tempera-
ture sensor
Input L-KÜ [9.1] DPT_Value_
Temp
2 bytes
56 Input 1 - Brightness
sensor
Input L-KÜ [9.4] DPT_Value_Lux 2 bytes
57 Input 1 - Scene Input L-KÜ [18.1] DPT_Scene-
Control
1 byte
58 Input 1 - Disable
object
Input LSK- [1.1] DPT_Switch 1 bit
60 Input 2 - Long-term Input LSKÜ [1.8] DPT_UpDown 1 bit
61 Input 2 - Short-term Input/out-
put
L-KÜ [1.8] DPT_UpDown 1 bit
62 Input 2 - Switching Output LSKÜ [1.1] DPT_Switch 1 bit
63 Input 2 - Dimming
relative
Input/out-
put
LSKÜ [3.7] DPT_Control_
Dimming
4 bit
64 Input 2 - 8 bit sensor Input/out-
put
L-KÜ [5] 5.xxx 1 byte
65 Input 2 - Tempera-
ture sensor
Output L-KÜ [9.1] DPT_Value_
Temp
2 bytes
66 Input 2 - Brightness
sensor
Input/out-
put
L-KÜ [9.4] DPT_Value_Lux 2 bytes
67 Input 2 - Scene Input/out-
put
L-KÜ [18.1] DPT_Scene-
Control
1 byte
68 Input 2 - Disable
object
Output LSK- [1.1] DPT_Switch 1 bit
70 Input 3 - Long-term Input/out-
put
LSKÜ [1.8] DPT_UpDown 1 bit
71 Input 3 - Short-term Output L--KÜ [1.8] DPT_UpDown 1 bit
72 Input 3 - Switching Output LSKÜ [1.1] DPT_Switch 1 bit
73 Input 3 - Dimming
relative
Input/out-
put
LSKÜ [3.7] DPT_Control_
Dimming
4 byte
74 Input 3 - 8 bit sensor Input L-KÜ [5] 5.xxx 1 byte
75 Input 3 - Tempera-
ture sensor
Output L-KÜ [9.1] DPT_Value_
Temp
2 bytes
Transmission protocol

2029825_0•en•2019-04-01 We reserve the right to make technical modifications 13
No. Text Function Flags DPT type Size
76 Input 3 - Brightness
sensor
Output L-KÜ [9.4] DPT_Value_Lux 2 bytes
77 Input 3 - Scene Input/out-
put
L-KÜ [18.1] DPT_Scene-
Control
1 byte
78 Input 3 - Disable
object
Input LSK- [1.1] DPT_Switch 1 bit
80 Input 4 - Long-term Output LSKÜ [1.8] DPT_UpDown 1 bit
81 Input 4 - Short-term Output L-KÜ [1.8] DPT_UpDown 1 bit
82 Input 4 - Switching Input/out-
put
LSKÜ [1.1] DPT_Switch 1 bit
83 Input 4 - Dimming
relative
Input LSKÜ [3.7] DPT_Control_
Dimming
4 bit
84 Input 4 - 8 bit sensor Output L-KÜ [5] 5.xxx 1 byte
85 Input 4 - Tempera-
ture sensor
Output L-KÜ [9.1] DPT_Value_
Temp
2 bytes
86 Input 4 - Brightness
sensor
Output L-KÜ [9.4] DPT_Value_Lux 2 bytes
87 Input 4 - Scene Output L-KÜ [18.1] DPT_Scene-
Control
1 byte
88 Input 4 - Disable
object
Input LSK- [1.1] DPT_Switch 1 bit
100 Channel A - Control
mode or manual
status
Output LSK- [1] 1.xxx 1 bit
101 Channel A - Manual
long-term shading
position
Input LSK- [1.8] DPT_UpDown 1 bit
102 Channel A - Manual
long-term closed
position
Input LSK- [1.8] DPT_UpDown 1 bit
103 Channel A - Manual
short-term
Input LSK- [1.8] DPT_UpDown 1 bit
104 Channel A - Manual
moving position
Input LSK- [5.1] DPT_Scaling 1 byte
106 Channel A - Manual
move to shading
position
Input LSK- [1.1] DPT_Switch 1 bit
107 Channel A - Manual
move to closed po-
sition
Input LSK- [1.1] DPT_Switch 1 bit
108 Channel A - Control
mode long-term
shading position
Input LSK- [1.8] DPT_UpDown 1 bit
109 Channel A - Control
mode long-term
closed position
Input LSK- [1.8] DPT_UpDown 1 bit
110 Channel A - Control
mode short-term
Input LSK- [1.8] DPT_UpDown 1 bit
111 Channel A - Control
mode moving po-
sition
Input LSK- [5.1] DPT_Scaling 1 byte
113 Channel A - Control
mode move to shad-
ing position
Input LSK- [1.1] DPT_Switch 1 bit
Transmission protocol

2029825_0•en•2019-04-01
We reserve the right to make technical modifications
14
KNX -Actuator
4M230.12 2Down REG
No. Text Function Flags DPT type Size
114 Channel A - Con-
trol mode move to
closed position
Input LSK- [1.1] DPT_Switch 1 bit
115 Channel A - Control
mode move to posi-
tion memory
Input LSK- [1.1] DPT_Switch 1 bit
116 Channel A - Control
mode position mem-
ory learning object
Input LSK- [1.1] DPT_Switch 1 bit
117 Channel A - Change
from manual to con-
trol mode
Input LSK- [1] 1.xxx 1 bit
118 Channel A - Control
mode disable object
Input LSK- [1.1] DPT_Switch 1 bit
119 Channel A - Current
moving position
Output L-KÜ [5.1] DPT_Scaling 1 byte
121 Channel A - Status
object
Output L-KÜ [1] 1.xxx 1 bit
122
Channel A - Retrieval
/ storage of scenes
Input LSK- [18.1] DPT_Scene-
Control
1 byte
123
Channel A - Outside
temp. disable object
Input LSK- [1.1] DPT_Switch 1 bit
124 Channel A - Outside
temperature barrier
measuring value
Input LSK- [9.1] DPT_Value_
Temp
2 bytes
125 Channel A - Outside
temperature barrier
status
Output L-KÜ [1.1] DPT_Switch 1 bit
126 Channel A - Dusk
object
Input LSK- [1.1] DPT_Switch 1 bit
127 Channel A - Dusk
measuring value
Input LSK- [9.4] DPT_Value_Lux 2 bytes
128 Channel A - Dusk
status
Output L-KÜ [1.1] DPT_Switch 1 bit
129 Channel A - Time
control
Input LSK- [1.1] DPT_Switch 1 bit
130 Channel A - Inside
temperature enable
object
Input LSK- [1.1] DPT_Switch 1 bit
131 Channel A - Inside
temperature enable
measuring value
Input LSK- [9.1] DPT_Value_
Temp
2 bytes
132 Channel A - Inside
temperature enable
set value
Input LSK- [9.1] DPT_Value_
Temp
2 bytes
133 Channel A - Inside
temperature enable
status
Output L-KÜ [1.1] DPT_Switch 1 bit
134 Channel A - Shading
object
Input LSK- [1.1] DPT_Switch 1 bit
135 Channel A - Shading
brightness measur-
ing value 1
Input LSK- [9.4] DPT_Value_Lux 2 bytes
136 Channel A - Shading
brightness measur-
ing value 2
Input LSK- [9.4] DPT_Value_Lux 2 bytes
137 Channel A - Shading
brightness measur-
ing value 3
Input LSK- [9.4] DPT_Value_Lux 2 bytes
Transmission protocol

2029825_0•en•2019-04-01 We reserve the right to make technical modifications 15
No. Text Function Flags DPT type Size
138 Channel A - Shading
limit value
Input/out-
put
LSKÜ [9.4] DPT_Value_Lux 2 bytes
139 Channel A - Shading
limit value
1 = + | 0 = -
Input LSK- [1]1.xxx 1 bit
140 Channel A - Shading
limit value +
Input LSK- [1]1.xxx 1 bit
141 Channel A - Shading
limit value -
Input LSK- [1]1.xxx 1 bit
142 Channel A - Shading
status
Input L-KÜ [1.1] DPT_Switch 1 bit
143 Channel A - Shading
position learning
object
Input/out-
put
LSK- [1]1.xxx 1 bit
144 Channel A - Azimuth Output LSK- [9]9 xxx 2 bytes
145 Channel A - Eleva-
tion
Input/out-
put
LSK- [9]9 xxx 2 bytes
161 Channel A - Zero
position reached
Input LSK- [1.1] DPT_Switch 1 bit
162 Channel A - Zero po-
sition sensor faulty
Output L-KÜ [1.1] DPT_Switch 1 bit
163 Channel A - Master
zero position status
Output L-KÜ [1.1] DPT_Switch 1 bit
164
Channel A - Master
zero position command
Output L-KÜ [1.1] DPT_Switch 1 bit
165 Channel A - Slave
zero position status
Input LSK- [1.1] DPT_Switch 1 bit
166 Channel A - Master
zero position status
Input LSK- [1.1] DPT_Switch 1 bit
167
Channel A - Master
zero position command
Input LSK- [1.1] DPT_Switch 1 bit
168 Channel A - Slave
zero position status
Output L-KÜ [1.1] DPT_Switch 1 bit
171 Channel A - Barrier
1 - Disable object
Input LSK- [1.1] DPT_Switch 1 bit
172
Channel A - Barrier 1
- Wind disable object
Input LSK- [1.1] DPT_Switch 1 bit
173 Channel A - Barrier
1 - Wind barrier
measuring value
Input LSK- [9.5] DPT_Val-
ue_Wsp
2 bytes
174
Channel A - Barrier 1
- Wind barrier status
Output L-KÜ [1.1] DPT_Switch 1 bit
175
Channel A - Barrier 1
- Rain disable object
Input LSK- [1.1] DPT_Switch 1 bit
176 Channel A - Barrier
2 - Disable object
Input LSK- [1.1] DPT_Switch 1 bit
177
Channel A - Barrier 2
- Wind disable object
Input LSK- [1.1] DPT_Switch 1 bit
178 Channel A - Barrier
2 - Wind barrier
measuring value
Input LSK- [9.5] DPT_Val-
ue_Wsp
2 bytes
179
Channel A - Barrier 2
- Wind barrier status
Output L-KÜ [1.1] DPT_Switch 1 bit
180 Channel A - Barrier
2 - Rain disable
object
Input LSK- [1.1] DPT_Switch 1 bit
Transmission protocol

2029825_0•en•2019-04-01
We reserve the right to make technical modifications
16
KNX -Actuator
4M230.12 2Down REG
No. Text Function Flags DPT type Size
181 Channel A - Barrier
3 - Disable object
Input LSK- [1.1] DPT_Switch 1 bit
182
Channel A - Barrier 3
- Wind disable objec t
Input LSK- [1.1] DPT_Switch 1 bit
183 Channel A - Barrier
3 - Wind barrier
measuring value
Input LSK- [9.5] DPT_Val-
ue_Wsp
2 bytes
184 Channel A - Barrier
3 - Wind barrier
status
Output L-KÜ [1.1] DPT_Switch 1 bit
185
Channel A - Barrier 3
- Rain disable object
Input LSK- [1.1] DPT_Switch 1 bit
186 Channel A - Barrier
4 - Disable object
Input LSK- [1.1] DPT_Switch 1 bit
187
Channel A - Barrier 4
- Wind disable object
Input LSK- [1.1] DPT_Switch 1 bit
188 Channel A - Barrier
4 - Wind barrier
measuring value
Input LSK- [9.5] DPT_Val-
ue_Wsp
2 bytes
189
Channel A - Barrier 4
- Wind barrier status
Output L-KÜ [1.1] DPT_Switch 1 bit
190
Channel A - Barrier 4
- Rain disable object
Input LSK- [1.1] DPT_Switch 1 bit
191 Channel A - Barrier
5 - Disable object
Input LSK- [1.1] DPT_Switch 1 bit
192
Channel A - Barrier 5
- Wind disable object
Input LSK- [1.1] DPT_Switch 1 bit
193 Channel A - Barrier
5 - Wind barrier
measuring value
Input LSK- [9.5] DPT_Val-
ue_Wsp
2 bytes
194
Channel A - Barrier 5
- Wind barrier status
Output L-KÜ [1.1] DPT_Switch 1 bit
195
Channel A - Barrier 5
- Rain disable object
Input LSK- [1.1] DPT_Switch 1 bit
249
Channel A - Local op-
eration disable object
Input LSK- [1.1] DPT_Switch 1 bit
250 Input 5 - Long-term Input/out-
put
LSKÜ [1.8] DPT_UpDown 1 bit
251 Input 5 - Short-term Output L-KÜ [1.8] DPT_UpDown 1 bit
252 Input 5 - Switching Input/out-
put
LSKÜ [1.1] DPT_Switch 1 bit
253 Input 5 - Dimming
relative
Input/out-
put
LSKÜ [3.7] DPT_Control_
Dimming
4 bit
254 Input 5 - 8 bit sensor Output L-KÜ [5] 5.xxx 1 byte
255 Input 5 - Tempera-
ture sensor
Output L-KÜ [9.1] DPT_Value_
Temp
2 bytes
256 Input 5 - Brightness
sensor
Output L-KÜ [9.4] DPT_Value_Lux 2 bytes
257 Input 5 - Scene Output L-KÜ [18.1] DPT_Scene-
Control
1 byte
258 Input 5 - Disable
object
Input LSK- [1.1] DPT_Switch 1 bit
260 Input 6 - Long-term Input/out-
put
LSKÜ [1.8] DPT_UpDown 1 bit
261 Input 6 - Short-term Output L-KÜ [1.8] DPT_UpDown 1 bit
Transmission protocol

2029825_0•en•2019-04-01 We reserve the right to make technical modifications 17
No. Text Function Flags DPT type Size
262 Input 6 - Switching Input/out-
put
LSKÜ [1.1] DPT_Switch 1 bit
263 Input 6 - Dimming
relative
Input/out-
put
LSKÜ [3.7] DPT_Control_
Dimming
4 bit
264 Input 6 - 8 bit sensor Output L-KÜ [5] 5.xxx 1 byte
265 Input 6 - Tempera-
ture sensor
Output L-KÜ [9.4] DPT_Value_
Temp
2 bytes
266 Input 6 - Brightness
sensor
Output L-KÜ [9.4] DPT_Value_Lux 2 bytes
267 Input 6 - Scene Output L-KÜ [18.1] DPT_Scene-
Control
1 byte
268 Input 6 - Disable
object
Input LSK- [1.1] DPT_Switch 1 bit
449
Channel B - Local op-
eration disable object
Input LSK- [1.1] DPT_Switch 1 bit
649
Channel C - Local op-
eration disable object
Input LSK- [1.1] DPT_Switch 1 bit
849
Channel D - Local op-
eration disable object
Input LSK- [1.1] DPT_Switch 1 bit
120 Channel A - Current
slat position
Output L-KÜ [5.1] DPT_Scaling 1 byte
196 Channel A - Short-
term limitation
Input LSK- [1.1] DPT_Switch 1 bit
105 Channel A - Manual
slat position
Input LSK- [5.1] DPT_Scaling 1 byte
112 Channel A - Control
mode slat position
Input LSK- [5.1] DPT_Scaling 1 byte
321 Channel B - Status
object
Output L-KÜ [1] 1.xxx 1 bit
319 Channel B - Current
moving position
Output L-KÜ [1.1] DPT_Switch 1 bit
320 Channel B - Current
slat position
Output L-KÜ [5.1] DPT_Scaling 1 byte
361 Channel B - Zero
position reached
Output LSK- [1.1] DPT_Switch 1 bit
364
Channel B - Master
zero position command
Input L-KÜ [1.1] DPT_Switch 1 bit
365 Channel B - Slave
zero position status
Output LSK- [1.1] DPT_Switch 1 bit
366 Channel B - Master
zero position status
Input LSK- [1.1] DPT_Switch 1 bit
367 Channel B - Master
zero position com-
mand
Input LSK- [1.1] DPT_Switch 1 bit
363 Channel B - Master
zero position status
Output L-KÜ [1.1] DPT_Switch 1 bit
368 Channel B - Slave
zero position status
Output L-KÜ [1.1] DPT_Switch 1 bit
396 Channel B - Short-
term limitation
Input LSK- [1.1] DPT_Switch 1 bit
317 Channel B - Change
from manual to con-
trol mode
Input LSK- [1] 1.xxx 1 bit
Transmission protocol

2029825_0•en•2019-04-01
We reserve the right to make technical modifications
18
KNX -Actuator
4M230.12 2Down REG
No. Text Function Flags DPT type Size
318 Summer compen-
sation: Barrier (1 =
disable)
Input LSK- [1.1] DPT_Switch 1 bit
371
Adjusting variable
comparator 1: Input 1
Input LSK- [1.1] DPT_Switch 1 bit
372
Adjusting variable
comparator 1: Input 2
Input LSK- [1.1] DPT_Switch 1 bit
374 Adjusting variable
comparator 1: Input 3
Output L-KÜ [1.1] DPT_Switch 1 bit
373
Adjusting variable
comparator 1: Input 4
Input LSK- [9.5] DPT_Val-
ue_Wsp
2 bytes
375
Adjusting variable
comparator 1: Input 5
Input LSK- [1.1] DPT_Switch 1 bit
376 Adjusting variable
comparator 1: Output
Input LSK- [1.1] DPT_Switch 1 bit
377 Adjusting variable
comparator 1: Barri-
er (1 : barriers)
Input LSK- [1.1] DPT_Switch 1 bit
379
Adjusting variable
comparator 2: Input 1
Output L-KÜ [1.1] DPT_Switch 1 bit
378
Adjusting variable
comparator 2: Input 2
Input LSK- [9.5] DPT_Val-
ue_Wsp
2 bytes
380
Adjusting variable
comparator 2: Input 3
Input LSK- [1.1] DPT_Switch 1 bit
381
Adjusting variable
comparator 2: Input 4
Input LSK- [1.1] DPT_Switch 1 bit
382
Adjusting variable
comparator 2: Input 5
Input LSK- [1.1] DPT_Switch 1 bit
384
Adjusting variable
comparator 2: Output
Output L-KÜ [1.1] DPT_Switch 1 bit
383 Adjusting variable
comparator 2: Barri-
er (1 : barriers)
Input LSK- [9.5] DPT_Val-
ue_Wsp
2 bytes
385
Adjusting variable
comparator 3: Input 1
Input LSK- [1.1] DPT_Switch 1 bit
386 Adjusting variable
comparator 3: Input 2
Input LSK- [1.1] DPT_Switch 1 bit
387
Adjusting variable
comparator 3: Input 3
Input LSK- [1.1] DPT_Switch 1 bit
389
Channel B - Barrier 4
- Wind barrier status
Output L-KÜ [1.1] DPT_Switch 1 bit
388
Channel B - Barrier 4
- Wind barrier status
Input LSK- [9.5] DPT_Val-
ue_Wsp
2 bytes
390
Channel B - Barrier 4
- Rain disable object
Input LSK- [1.1] DPT_Switch 1 bit
391 Channel B - Barrier
5 - Disable object
Input LSK- [1.1] DPT_Switch 1 bit
392
Channel B - Barrier 5
- Wind disable object
Input LSK- [1.1] DPT_Switch 1 bit
394
Channel B - Barrier 5
- Wind barrier status
Output L-KÜ- [1.1] DPT_Switch 1 bit
393 Channel B - Barrier
5 - Wind barrier
measuring value
Input LSK- [9.5] DPT_Val-
ue_Wsp
2 bytes
395 Channel B - Barrier
5 - Rain disable
object
Input LSK- [1.1] DPT_Switch 1 bit
Transmission protocol

2029825_0•en•2019-04-01 We reserve the right to make technical modifications 19
No. Text Function Flags DPT type Size
316 Channel B - Control
mode position mem-
ory learning object
Input LSK- [1.1] DPT_Scaling 1 bit
315 Channel B - Control
mode move to posi-
tion memory
Input LSK- [1.1] DPT_Scaling 1 bit
308 Channel B - Control
mode long-term
shading position
Input LSK- [1.8] DPT_UpDown 1 bit
309 Channel B - Control
mode long-term
closed position
Input LSK- [1.8] DPT_UpDown 1 bit
310 Channel B - Control
mode short-term
Input LSK- [1.8] DPT_UpDown 1 bit
311
Channel B - Control
mode moving position
Input LSK- [5.1] DPT_Scaling 1 byte
312 Channel B - Control
mode slat position
Input LSK- [5.1] DPT_Scaling 1 byte
313 Channel B - Control
mode move to shad-
ing position
Input LSK- [1.1] DPT_Switch 1 bit
314 Channel B - Con-
trol mode move to
closed position
Input LSK- [1.1] DPT_Switch 1 bit
323 Channel B - Outside
temperature disable
object
Input LSK- [1.1] DPT_Switch 1 bit
325 Channel B - Outside
temperature barrier
status
Output L-KÜ [1.1] DPT_Switch 1 bit
324 Channel B - outside
temperature barrier
measuring value
Input LSK- [9.1] DPT_Value_
Temp
2 bytes
326 Channel B - Dusk
object
Input LSK- [1.1] DPT_Switch 1 bit
328 Channel B - Dusk
status
Output L-KÜ [1.1] DPT_Switch 1 bit
327 Channel B - Dusk
measuring value
Input LSK- [9.4] DPT_Value_Lux 2 bytes
329 Channel B - Time
control
Input LSK- [1.1] DPT_Switch 1 bit
330 Channel B - Inside
temperature enable
object
Output L-KÜ [1.1] DPT_Switch 1 bit
331 Channel B - Inside
temperature enable
measuring value
Input LSK- [9.1] DPT_Value_
Temp
2 bytes
332 Channel B - Inside
temperature enable
set value
Input LSK- [9.1] DPT_Value_
Temp
2 bytes
334 Channel B - Shading
object
Input LSK- [1.1] DPT_Switch 1 bit
339 Channel B - Shading
limit value
1 = + | 0 = -
Input LSK- [1] 1.xxx 1 bit
340 Channel B - Shading
limit value +
Input LSK- [1] 1.xxx 1 bit
341 Channel B - Shading
limit value -
Output LSK- [1] 1.xxx 1 bit
Transmission protocol

2029825_0•en•2019-04-01
We reserve the right to make technical modifications
20
KNX -Actuator
4M230.12 2Down REG
No. Text Function Flags DPT type Size
338 Channel B - Shading
limit value
Input/out-
put
LSKÜ [9.4] DPT_Value_Lux 2 bytes
342 Channel B - Shading
status
Output L-KÜ [1.1] DPT_Switch 1 bit
335 Channel B - Shading
brightness measur-
ing value 1
Input LSK- [9.4] DPT_Value_Lux 2 bytes
336 Channel B - Shading
brightness measur-
ing value 2
Input LSK- [9.4] DPT_Value_Lux 2 bytes
337 Channel B - Shading
brightness measur-
ing value 3
Input LSK- [9.4] DPT_Value_Lux 2 bytes
344 Channel B - Azimuth Input LSK- [9] 9.xxx 2 bytes
345 Channel B - Eleva-
tion
Input LSK- [9] 9.xxx 2 bytes
343 Channel B - Shading
position learning
object
Input LSK- [1] 1.xxx 1 bit
322 Channel B - Re-
trieval / storage of
scenes
Input LSK- [18.1] DPT_Scene-
Control
1 byte
452 Input 7 - Switching Input/out-
put
LSKÜ [1.1] DPT_Switch 1 bit
458 Input 7 - Disable
object
Input LSK- [1.1] DPT_Switch 1 bit
450 Input 7 - Long-term Input/out-
put
LSKÜ [1.8] DPT_UpDown 1 bit
451 Input 7 - Short-term Output L-KÜ [1.8] DPT_UpDown 1 bit
453 Input 7 - Dimming
relative
Input LSKÜ [3.7] DPT_Control_
Dimming
4 bit
454 Input 7 - 8 bit sensor Output L-KÜ [5] 5.xxx 1 byte
455 Input 7 - Tempera-
ture sensor
Output L-KÜ [9.1] DPT_Value_
Temp.
2 bytes
456 Input 7 - Brightness
sensor
Output L-KÜ [9.4] DPT_Value_Lux 2 bytes
457 Input 7 - Scene Output L-KÜ [18.1] DPT_Scene-
Control
1 bit
362 Channel B - Zero po-
sition sensor faulty
Output L-KÜ [1.1] DPT_Switch 1 bit
462 Input 8 - Switching Input/out-
put
LSKÜ [1.1] DPT_Switch 1 bit
468 Input 8 - Disable
object
Input LSK- [1.1] DPT_Switch 1 bit
460 Input 8 - Long-term Input/out-
put
LSKÜ [1.8] DPT_UpDown 1 bit
461 Input 8 - Short-term Output L-KÜ [1.8] DPT_UpDown 1 bit
463 Input 8 - Dimming
relative
Input/out-
put
LSKÜ [3.7] DPT_Control_
Dimming
4 bit
464 Input 8 - 8 bit sensor Output L-KÜ [5] 5.xxx 1 byte
465 Input 8 - Tempera-
ture sensor
Output L-KÜ [9.1] DPT_Value_
Temp.
2 bytes
466 Input 8 - Brightness
sensor
Output L-KÜ [9.4] DPT_Value_Lux 2 bytes
Transmission protocol