WAREMA KNX secure Series User manual

1
warema_2048815_alhb_en_v1•2022-02-01 We reserve the right to make technical modifications
General information
Fig. 1 WAREMA KNXsecure8M230.16I pro AP
The KNXsecure2/4/6/8M230.xIpro AP/REG sun shading
actuator is a device for the central operation of up to eight
230VAC sun shading drives (the following uses the sun
shading actuator for eight motors with 16 binary inputs as
an example).
The device is operated using a KNX bus system. The
drives and the motor control unit are supplied via a
230VAC control line.
KNX secure can be used with the actuator. A device certifi-
cate (preset key at the factory) is required for this. This is
located on the side of the device as a sticker and is also
included as a device card.
Store the device card separately and also remove
the sticker from the device to ensure maximum
security.
The device certificate is unique to each device and
cannot be changed or deleted.
Recovery of the device certificate is NOT possib-
le in the event of loss!
KEEP IN A SAFE PLACE FOR COMMISSIONING!
Affix the KNX secure actuator ID label here/
note installation location if necessary
VGVKXL-FNV2XS
Device Certification
SNR: 08154711
KNX secure 8M230.16I AP pro
AAFC4Z-YWCGQK-
DIVDUS-S2NJ5I-
Intended use
The KNXsecure2/4/6/8M230.xI pro AP/REG is an
electronic device for controlling sun shading devices. The
approval of the manufacturer must be obtained for any use
of the device other than its intended purpose specified in
these instructions.
Safety instructions
ARNINGW
The electrical installation (assembly)/dis-
mantling must be performed by a certified
electrician in accordance with VDE0100
and/or with the standards and legal require-
ments pertaining to the respective country.
The electrician must observe the installa-
tion notes and instructions included with
the electrical devices supplied.
ARNINGW
If hazard-free operation cannot be
assumed, the device must not be started
or must be deactivated. This assumption is
justified if:
the housing or the connecting lines show signs of
damage,
the device is no longer working.
ARNINGW
It is important to comply with the following
points in the interest of personal safety.
 Children must not play with the operating elements
of the control unit or the remote control. Store remote
controls out of reach of children.
 Make sure that no persons or objects are in the path of
the driven parts (internal and external venetian blinds,
etc.).
 Disconnect the device from the operating voltage if
cleaning or other maintenance work must be per-
formed!
Function
The software functions of the KNXsecure2/4/6/8M230.
xIpro AP/REG are described in detail in the software
manual (article number 2048818). You can download
the manual and the product database of the sun shading
actuator from www.warema.de/knx.
The device can be updated via the WAREMA service app
(ETS app).
The KNX secure2/4/6/8M230.xI pro AP/REG is equipped
with automatic current monitoring.
Installation instructions
WAREMA KNX secure
2/4/6/8M230.xI pro AP/REG
Valid from
1st February 2022
Keep for future use.

warema_2048815_alhb_en_v1•2022-02-01We reserve the right to make technical modifications
2
The actuator makes it possible to automatically detect the
run times of the connected sun shading products via the
electronic or mechanical limit switch-off of the motors. The
detection of the run time can be triggered automatically in-
dividually for each output after commissioning or manually.
Different run times of the sun shading products are thus
possible and are recognised. The automatic run time detec-
tion can be switched off separately per output or altogether.
Installation
Insert a slotted screwdriver (recommendation: 3.0 - 4.0mm
blade) into the respective cover opening (Fig. 3) and care-
fully pry open the hinged cover. Repeat the procedure for
the second opening of the cover. After both latches have
been unlatched, the cover can be removed. Open the
second cover in the same way. Alternatively, the AP prod-
uct variant, like the REG product variant (article number
2040768), can also be mounted on a DIN rail (TH35-15).
Electrical connection
An on-site overload current protection device (fuse) and a
disconnecting and isolating switch to switch off the entire
unit must be provided.
The electrical connection is made as shown in the wiring
diagram on the reverse side (Fig. 5), the connection to the
KNX bus system and the drives is made using spring termi-
nals, the connecting lines are designed as screw terminals.
ARNINGW
After installation, all terminals and connec-
tions under current must be completely
closed by the latched cover to prevent acci-
dental contact. It should not be possible to
open the latched cover without using tools.
Commissioning
After the installation has been completed and the operating
voltages have been applied, the connected drives can be
checked via Bluetooth using an app.
You will find a detailed description on the further commis-
sioning in the KNX secure software manual
(art. no. 2048818).
Local operation
You will find the app for operating the KNX sun shading ac-
tuator in the Apple AppStore and in the Google Play Store.
Download this to your smartphone.
After starting the app, the surrounding area is scanned for
WAREMA sun shading actuators. Available actuators are
shown and can be operated.
Operation via app has the same priority as manual opera-
tion via group objects. The operating behaviour is as
follows:
Brief push of the button = Stop/step move command
Long push of the button = Up/Down move command.
A detailed description of the operation is integrated in the
app and can also be found in the associated KNX secure
software manual (art. no. 2048818).
The communication between the smartphone and
the KNX devices is established via Bluetooth. This
function can be switched off using the ETS (in de-
fault mode, the function is always "On").
During parameterisation, change the default pass-
word in accordance with your specifications and
memorise your password in order to prevent ope-
ration by unauthorised persons.
ARNINGW
Never randomly press the push button on
the app without having a line of sight to the
sun shading system.
Programming
You can perform programming either in the app or directly
on the device.
There is a Prog button for programming and a display LED
both in the app and on the keypad (see Fig. 2).
The procedure here is basically the same:
 Press the programming button in the app or on the
device (Fig. 2) to put the device into programming
mode. The red LED lights up when programming mode
is active. Programming is performed using the ETS on
the PC. This software ends the programming mode
automatically. The red LED goes out.
 If the programming mode is to be ended earlier, press
the programming button again. The red LED goes out.
Fig. 2 Keypad view
Maintenance
There are no parts inside the device that require mainte-
nance. In the event of a malfunction, the built-in miniature
fuses should only be replaced by a certified electrician.
Cleaning
Clean the housing with a soft, dry cloth. Do not use deter-
gents, cleaning agents, solvents, abrasive substances or
steam cleaners!
Liability
Failure to comply with the product information in these in-
structions and any use of the device other than its intended
use may result in the manufacturer refusing to honour
warranty claims for product damage. In this case, liability
for secondary harm to persons or damage to property will
also be excluded. Observe the information in the operating
instructions for your sun shading system. The automatic
or manual operation of the sun shading system while iced
over and the use of the sun shading system during severe
weather may cause damage and must be prevented by the
operator through suitable precautions.

3
warema_2048815_alhb_en_v1•2022-02-01 We reserve the right to make technical modifications
Obligations for the disposal of electrical devices
A marking with this symbol indicates the following
obligations under the scope of legal regulations:
 The owner of this electrical device must dispose of it
separately from unsorted municipal waste for further
recycling.
 Used batteries and accumulators that are not enclosed
in the old device, as well as lamps/bulbs that can be
removed from the old device without breaking, must be
disposed of separately.
 Distributors of electrical devices and disposal companies
are obliged to take back the equipment free of charge.
 The owner must take it upon themselves to delete any
personal data contained on the electrical device prior to
disposal
After use, the device must be disposed of according to
legal regulations or turned in to your local recycling centre.
Technical data
KNXsecure 2/4/6/8M230.xI pro
AP/REG min. typ. max. Unit
Operating voltage 198 230 253 VAC
Mains frequency 50 50 60 Hz
Power consumption at 230VAC for
2M230.xl pro AP/REG 0.9 - 1.7 W
4M230.xl pro AP/REG 0.9 - 2.5 W
6M230.xl pro AP/REG 0.9 - 2.8 W
8M230.xl pro AP/REG 0.9 - 3.4 W
Output per drive*
Switching capacity 230VAC/
cosφ = 0.6
500 VA
*The total power per fuse must not exceed 1000 VA.
KNX Interface TP 1
Current consumption KNX 3.5 13 mA
Voltage 29 VDC
Inputs on local operating elements (sunblind push buttons,
1-pin) and signal inputs
Voltage, active 8 24 36 VDC
Current, active 0.5 1 1.5 mA
Voltage, inactive -0.5 0 1 VDC
Bluetooth transceiver
Transmission frequency 2.402 2.480 GHz
Transmission power 0 dBm
Input sensitivity -90 dBm
Operating range (environment
without interference)
5 m
Ambient conditions
Operating temperature 0 50 °C
Storage temperature 0 70 °C
Humidity
(not condensing)
10 40 85 %Frel
Degree of soiling 2
Connection
Connecting line Screw terminals
KNX bus system, drives, push
button inputs
Spring terminals
Wire cross sections
Connecting line max. 2.5mm²
KNX bus system 0.6 - 0.8mm∅
Motor outputs, push button inputs max. 1.5mm²
Housing
Surface-mounted housing
degree of protection
IP30
Safety class (PE is looped through) I
Miscellaneous
Conformity Specified under
www.warema.de/ce
This device complies with the EMC directives for use in
residential and commercial areas.
Article numbers
KNXsecure2M230.8I AP pro 2040 737
KNXsecure4M230.8I AP pro 2040 739
KNXsecure4M230.8I REG
pro
2040 767
KNXsecure6M230.16I AP pro 2040 761
KNXsecure8M230.16I AP pro 2040 763
WAREMA Renkhoff SE
Hans-Wilhelm-Renkhoff-Str. 2
97828 Marktheidenfeld, Germany
Fuse protection
KNXswitch actuator type Quan-
tity Fuse protection
KNXsecure2M230.8I AP pro 1 x 6.3 AT H
KNXsecure4M230.8I AP pro 1 x 6.3 AT H
KNXsecure4M230.8I REG pro 1 x 6.3 AT H
KNXsecure6M230.16I AP pro 2 x 6.3 AT H
KNXsecure8M230.16I AP pro 2 x 6.3 AT H
210 mm *
119 mm
184 mm *
180 mm
60 mm
3 ‒ 4 mm
*KNX secure 2M230.8I AP: 158 mm / 132 mm 9MW
KNX secure 4M230.8I AP: 158 mm / 132 mm 9MW
KNX secure 6M230.16I AP: 210 mm / 184 mm 12MW
KNX secure 8M230.16I AP: 210 mm / 184 mm 12MW
Fig. 3 Dimensions
60 mm
95 mm 90 mm
157 mm / 9 MW
60 mm
Fig. 4 Dimensions of 9 MW DIN rail-mounted housing for
KNX secure 4M230.8I REG.

warema_2048815_alhb_en_v1•2022-02-01We reserve the right to make technical modifications
4
1.1
1.1
1.2
1.2
2.1
2.1
2.2
2.2
3.1
3.1
3.2
3.2
4.1
4.1
4.2
4.2
In+
In+
In1
In1
In+
In+
In2
In2
In+
In+
In3
In3
In+
In+
In4
In4
X20:
X20:
5.1
5.1
5.2
5.2
In+
In+
In5
In5
6.1
6.1
6.2
6.2
In+
In+
In6
In6
7.1
7.1
7.2
7.2
In+
In+
In7
In7
8.1
8.1
8.2
8.2
In+
In+
X50:
X50:
KNX
KNX
-
-
+
+
X40:
X40:
L
L
L
L
N
N
N
N
1
1
2
2
3
3
4
4
5
5
6
6
All push button lines JY(St)Y 2×2×0.8 mm Max. line length 200m for interference-proof routing, use a twisted paired line.
Binary inputs freely usable in KNX
PE N L
231
BU BK BN GNYE
M∼
Motor 1
sun shading system
231
BU GNYE
M∼
Motor 2
sun shading system
NPE N
BK BN
PE
231
BU BK BN GNYE
M∼
Motor 3
sun shading system
231
BU BK BN GNYE
M∼
Motor 4
sun shading system
NPE NPE
ATTENTION: Only one motor can be connected per motor terminal set! If interconnected, the motor will be damaged. The total power per fuse must not exceed 1000VA.
All motor lines H05-RR-F 4 G 0.75 BK type WAREMA
Connecting line 230 V AC, 50/60 Hz, 16 A, 3 x 1.5 mm2
231
BU BK BN GNYE
M∼
Motor 5
sun shading system
231
BU BK BN GNYE
M∼
Motor 6
sun shading system
NPE NPE
231
BU BK BN GNYE
M∼
Motor 7
sun shading system
231
BU BK BN GNYE
M∼
Motor 8
sun shading system
NPE NPE
KNX secure 8M230.16I AP F1
6,3 AT H
6,3 AT H
F2
X1:
X1:
Motor 1
Motor 1
N
N
N
N
X3:
X3:
X2:
X2:
X4:
X4:
X6:
X6:
X8:
X8:
N
N
X5:
X5:
N
N
N
N
N
N
X7:
X7:
N
N
M1.1
M1.1
M1.2
M1.2
Motor 2
Motor 2
N
N
M2.1
M2.1
M2.2
M2.2
Motor 3
Motor 3
M3.1
M3.1
M3.2
M3.2
Motor 4
Motor 4
N
N
M4.1
M4.1
M4.2
M4.2
Motor 5
Motor 5
M5.1
M5.1
M5.2
M5.2
Motor 6
Motor 6
M6.1
M6.1
M6.2
M6.2
Motor 7
Motor 7
M7.1
M7.1
M7.2
M7.2
Motor 8
Motor 8
M8.1
M8.1
M8.2
M8.2
-
+
-
+
All bus lines YCYM 2×2×0.8 mm
KNX Bus KNX Bus
Fig. 5 Connection example KNXsecure8M230.16 AP