Wine racks America Base Horizontal Display User manual

Base Horizontal Display
Assembly GUIDE
Cordless Drill Finish Nailer
Hammer Nail Setter
Wood Glue
*Please verify that you have the correct number of parts before proceeding.
Depending on the model you purchased, your bundle should contain the following:
Package Contents tools for assembly
Page 1
or visit
wineracksamerica.com
Questions?
888.373.6057
Required
Suggested
ScrewdriverAllen Wrench
*Follow the same assembly procedure for all Base Label Out Display models
WOOD SCREWS FINISH NAILS
TOP PANEL (x1)
BOTTOM PANEL (x1)
TRIM PIECE (x1)
WOOD PUTTY
SIDE PANEL (x2)
METAL RODS (x28)
WOOD SHIM RAIL SCREWS

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Base Horizontal Display
Page 2
1. Find an open, flat area in which to work. Carefully remove all components from the box and remove any packaging
materials. Check the parts list to verify package contents.
1
START WITH
4 CORNERS
2. Begin by attaching 4 metal rods into the pre-drilled holes on the four corners of each side piece. Using an allen wrench
or drill, carefully attach each metal screw to the 4 metal rods. Do not tighten until ALL metail rods have been
attached. Be sure that the notches on the side panels are both facing inwards and at the bottom. (figure 1)
3. Attach the remaining metal rods to the side panels using the provided metal screws. (figure 2)
Do not tighten screws until ALL rods have been attached. After are attached, carefully tighten each metal screw
all the way. *Do not overtighten.
2
ATTACH REMAINING
METAL RODS
Notches

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Base Horizontal Display
Page 3
4. Slide the bottom panel into the two grooves on each side panel. Using the provided wood screws, attach the bottom
panel to each side panel. (figure 3)
5. At this point, there is no specific front of the rack. Choose the side of the rack that you would like to be the front
and secure the bottom trim piece. The bottom trim piece should be flush with the bottom of the rack.
We recommend that you use a finish nailer to drive a nail through the trim piece into each side frame piece.
If you do not have a finish nailer, drive one of the provided finish nails into each side frame piece using a hammer
until it is flush with the surface trim piece. Use wood glue for added support.
Fill the nail holes using the wood putty provided. Push a small amount of putty into each hole and wipe excess putty
off the surface using a damp cloth. (figure 4)
3
ATTACH BOTTOM
PANEL
BOTTOM PANEL
4
ATTACH
TRIM PIECE

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Base Horizontal Display
Page 4
7. To prevent the bottom of the rack from bowing under the weight of your bottles, slide the bottom frame shim
under the back of the rack. (figure 6)
360 North 700 West Suite F • North Salt Lake, UT 84054
(toll free) 888-373-6057
(fax) 801-936-0534
Once again, thank you for your business. Remember, customer
service is available to answer any questions Monday-Friday
7:00 am - 5:00 pm MST. Please feel free to contact us for any
wine storage needs.
We would love to see your wine racks in use! Please feel free to
send any photos of your rack to [email protected]
WINERACKSAMERICA.COM
6. Attach the top panel to the side panels using the wood screws provided. Keep the side panels and top panel held
tightly together when securing. Be sure that the puck light cord comes out towards the back of the rack. (figure 5)
5
AT TA C H
TOP PANEL
6
INSERT
SHIM PIECE
8. If you purchased a solid top, secure it by placing a small amount of wood glue on the top of the box frame. Clamp
the top to the frame using standard wood clamps until fully dry. (figure 7)
7
ATTACH SOLID
TOP (OPTIONAL)