Wine racks America Wall Display User manual

Cordless Drill Utility Knife
Finish Nailer Hammer
Nail Setter
Wood Glue
*Please verify that you have the correct number of parts before proceeding.
Depending on the model you purchased, your bundle should contain the following:
Wall Display
Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Package Contents tools for assembly
Page 1
SCREWLESS BASE CONNECTOR (X1)
STANDARD CONNECTOR (X2)
SCREWLESS CONNECTOR (X4)
STANDARD BASE CONNECTOR (X1)
END LADDER
(X2)
MIDDLE LADDER
(X2)
Screwless Connectors
Screwless Base Connector
Trim Piece
Small Bottle Support
Large Bottle Support
End Ladder
Trim Piece Standard Connectors
Middle Ladder
Standard Base
Connector
Screwless Connectors
Top Supports
TRIM PIECE (X2)
TOP SUPPORT (X2)
LARGE BOTTLE
SUPPORT (X18)
SMALL BOTTLE
SUPPORT (X18)
*DEPENDING ON MODEL
WOOD SCREWS
FINISH NAILS
WOOD PUTTY
SHELF
SUPPORT (x18)

ATTACHING YOUR RACK TO THE WALL
Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Page 2
Wall Display
Step 1: Place parts on a flat surface. Begin by attaching the back connectors to the ladders with a cordless drill. The trim
piece will need to be attached with provided finish nails, a brad nailer or wood glue.
BACK FRONT
Step 2: Flip rack over. Use brad nailer or provided finish nails to attach front connectors to the ladders.
Use wood glue for added support.
16 1/2"
31"
Base connectors
are 2" tall
Measurements are from
the bottom of the rack to
the top of the connector
IMPORTANT!
Trim Piece
Step 3: Attach top screwless connectors and top supports using brad nailer or provided finish nails.
*NOTE: If you are planning on adding a top to your wall display, you will need to remove the front and back trim pieces, as
well as the top supports before installing.
TOP
Screwless Connectors Top Supports
Step 4: Insert large and small bottle supports into notched slots.
Large Bottle Supports
Small Bottle Supports
*NOTE: If you purchased a liquor wall display,
place shelf supports into notched slots.
Shelf Supports

ATTACHING YOUR RACK TO THE WALL
Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Page 3
Wall Display
Step 5: Use a screwdriver or cordless drill to attach vertical supports to the bottom and middle supports. Drive screw
through pre-drilled holes on the back of the vertical supports. Wood glue is highly suggested for added support.
Left Side Middle Right Side
Step 6: Use a screwdriver or cordless drill to attach vertical bottle holders to the wall display rack. Place vertical bottle
holder so the bottom is resting on the connector. Drive screws through pre-drilled holes on the sides of the
vertical supports.
*NOTE: Unless you are stacking multiple units, you will only need one right side vertical bottle holder.
ATTACHING VERTICAL BOTTLE HOLDERS
Vertical Bottle Holder Parts List:
VERTICAL SUPPORT
MIDDLE (X3)
VERTICAL SUPPORT
LEFT/RIGHT (X4)
BOTTOM SUPPORT
MIDDLE (X3)
BOTTOM SUPPORT
LEFT (X2)
BOTTOM SUPPORT
RIGHT (X2)
NECK SUPPORT
MIDDLE (X3)
NECK SUPPORT
LEFT/RIGHT (X4)

ATTACHING YOUR RACK TO THE WALL
Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Page 4
Depending on how many bottles you store, your wine cellar rack could weigh as much as 540 lbs.
To avoid tipping attach your racking to the wall using one of the following methods.
1. Put the rack in the desired location.
2. Shim the front of the rack so it is
parallel with the wall behind it.
3. Locate a wall stud behind the rack.
4. Drive a 2 1/2" wood screw through a
back spacer bar to attach to the stud.
1. Use "L" brackets (located at any hardware store).
2. Attach to both the rack and the wall in any out of
the way spot.
ATTACHING YOUR RACK TO THE WALL
Wall Display