Wren Kitchens Vogue TOWER UNIT Boiler Housing User manual

TOWER UNIT
Boiler Housing Assembly Guide
For Internal Use: FI.WR.INS.059_WKIN00180_Tower_600_2DrBoilerHoising_Guide_Rev5
2070 x 600
50/50 2070 x 600 70/30
2250 x 600 Tall
50/50 2250 x 600 Tall 70/30

Page 1
TOWER UNIT
Boiler Housing Assembly Guide
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
Panel B
x2 End Panel x1 Base Panel x1 Top Panel
Panel C Btm Panel C Top Panel E
x2 Rail
Legs
x5
Frontal (packed separately)
x2
70/30 OPTION
50/50 OPTION
L Bracket SML
(FF) x4
Hinge
Mounting Plate
x5 Inc Screws
Hinge
x5 Inc Screws
(U) x2
Fixing Plate
(F) x16
Wooden
Dowel
(L) x24
15mm
Screw
(G) x16
Cam Dowel
(Expanding)
(H) x12
Cam lock
(M) x4
Cover Cap
(K) x10
30mm
Screw
(N) x2
Door Buer
L Bracket LGE
x2
(Z) x24
Shelf Peg
Plastic
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.059_WKIN00180_Tower_600_2DrBoilerHoising_Guide_Rev5
NB. All Cam Lock (H) are to be positioned facing
the outside of the unit carcase, for ease of tightening.
Step 4.
Insert cam lock (H).
Do NOT tighten until Step 6.
Do not use power tools with
cam dowel (G) or cam lock (H)
Seat (G)
Cam Dowel
into hole as
shown.
B
B
View from underside View from underside
H
G
GH
C Top C Top
B
E
E
C Btm
C Top
B
GFF G
G F F G Btm
Top
B
RHLH
GFFG
GFFG
B
G
F
F
G
F
F
G
F
F
G
F
F
Dowel (F)
& Cam Dowel (G)
location detail
Step 2.
Seat dowel (F) into
holes in both end
panels (B)
as shown.
Step 1.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Step 3.
Attach panels (C Top, Btm) and (E) to panels (B),
using cam dowel (G) (in blue) and also using
Dowels (F) (in orange) in positions as shown.

Page 3
TOWER UNIT
Boiler Housing Assembly Guide
B
B
Front
Front
C
Leg position diagram
Step 5.
Position legs as shown.
Ensure legs are rotated to also provide
support to the end panels (B).
Step 6.
Secure each of the legs into place with
4 x 15mm screws (L) per leg.
B
LL
L
L
C
B
C
Step 7.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning unit upright.
Once in situ level accordingly.
It is important to lift unit
onto its legs. Do not tilt as
depicted in image.

Page 4
For Internal Use: FI.WR.INS.059_WKIN00180_Tower_600_2DrBoilerHoising_Guide_Rev5
70/30
HINGE
POSITION
50/50
HINGE
POSITION
70/30
1826mm
846mm
1336mm
626mm
126mm 126mm
866mm
1086mm
1826mm
1794mm
814mm
1304mm
594mm
94mm 94mm
834mm
1054mm
1794mm
50/50
BB
From Bottom From Bottom
L
L
FrontFront
INSIDE
FACE
INSIDE
FACE
Step 8.
Attach hinge plates onto end panels (B) to suit as shown using screws already located in the hinge
plates.
Hinge side or sides to be mounted in accordance to Customer Specic Kitchen Plan.

Page 5
TOWER UNIT
Boiler Housing Assembly Guide
70/30
HINGE
POSITION
50/50
HINGE
POSITION
70/30
2006mm 2006mm
1426mm
846mm
626mm
126mm 126mm
806mm
1026mm
1516mm
1974mm 1974mm
1394mm
814mm
594mm
94mm 94mm
774mm
994mm
1484mm
50/50
B B
From Bottom From Bottom
FrontFront
INSIDE
FACE
INSIDE
FACE
Step 9.
Attach hinge plates onto end panels (B) to suit as shown using screws already located in the hinge
plates.
Hinge side or sides to be mounted in accordance to Customer Specic Kitchen Plan.

Page 6
For Internal Use: FI.WR.INS.059_WKIN00180_Tower_600_2DrBoilerHoising_Guide_Rev5
Secure tower to the wall using L brackets LGE. Use 2 x 15mm screws (L) to secure each of the L
bracket LGE to the unit at either side. Then screw through into the wall as shown.
Screw into any side units using the 30mm screws (K)
provided to secure to unit.
Screw just to the rear of the hinge mounting plates,
at the top and bottom of both sides of the unit, place
cover caps (M) on the heads to conceal them.
K
Screws for attaching to walls are not provided as these vary depending on materials,
thickness and construction. Ensure appropriate xings for wall construction are used.

Page 7
TOWER UNIT
Boiler Housing Assembly Guide
Hinge cover caps
UU
See Customer Specic Kitchen Plan
For Tower Frontals
Fixing plates
Step 12.
Align doors to join together using 2 x xing plates (U) to the back
of both frontals ensure a 4mm gap is maintained between each
frontal once xed together.
Screw in place using 4 x 15mm screws (L) per xing plate.
Step 10.
Insert hinge where required
in holes as shown.
Step 11.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 14.
Fit cover caps to hinge.
Adjust Soft close to suit.
Step 13.
Adjust hinge to suit. As shown below.
View from Inside of unit
To adjust hinge using a
screw driver, tighten or
loosen as
required at points 1& 2.
Point 1- In - Out
Point 2- Left - Right
12
FRONTAL HINGE
ADJUSTMENT
To Release door
Pull catch as shown,
to release hinge
from the hinge
plate.
To Move the
hinge up/down,
loosen screws
A + B,
Manoeuvre
the door, then
re-tighten the
screws
A
B
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.

Page 8
For Internal Use: FI.WR.INS.059_WKIN00180_Tower_600_2DrBoilerHoising_Guide_Rev5