Wren Kitchens FRONTALS Parts list manual

FRONTALS
Drawer Frontal Replacement Guide
For Internal Use: FI.WR.INS.076_WKIN0066_Drawer_ReplaceFRTL_Rev6
Grass Drawer Box Removal
Grass Drawer Box Insertion
Grass Standard Drawer
Grass Deep Drawer
Grass Glass Drawer
TM Drawer Box Removal
TM Drawer Insertion
TM Standard Drawer
TM Mid Drawer
TM Deep Drawer
TM Mid Glass Drawer
TM Deep Glass Drawer
TM Drawer Side Cover Cap
Pg 1.
Pg 2.
Pg 3.
Pg 4.
Pg 5-6.
Pg 7.
Pg 8.
Pg 9.
Pg 10.
Pg 11.
Pg 12.
Pg 13.
Pg 14.

Page 1
FRONTALS
Drawer Frontal Replacement Guide
Step 2.
In one smooth motion, lift the front of the drawer,
this will disconnect the runner from the connectors
on the base of the drawer.
Once properly separated a click will be heard and the
drawer will be separate from the runner.
If this motion is not done with enough force then
the drawer may need to be lifted again.
Be careful not to lift the runners whilst lifting the
drawer.
Step 3.
The drawer is free to remove from the unit
Simply remove the loose drawer from the unit,
making sure not to damage the unit in the
process.
GRASS DRAWER BOX REMOVAL
Step 1.
Open the drawer that is required to be removed.
Pull out the drawer until the runners are at full
extension.
Removing a drawer is the same process for
Standard, Deep and Glass Drawers

Page 2
For Internal Use: FI.WR.INS.076_WKIN0066_Drawer_ReplaceFRTL_Rev6
Step 1.
Fully extend the drawer runners out of the unit
(for the drawer you are inserting).
Step 3.
Once the drawer is placed onto the runners,
pull forward the protruding lips on the ends
of the runners until a click is heard. Once the
click is heard the drawer is properly located and
secured to the runner.
Push the drawer back into the Unit.
Step 2.
Place the drawer onto the runners, making sure
that the groove of the drawer sides and the
runner mechanism are aligned.
GRASS DRAWER BOX INSERTION
Inserting a drawer is the same process for
Standard, Deep and Glass Drawers

Page 3
FRONTALS
Drawer Frontal Replacement Guide
GRASS STANDARD DRAWER
Frontal fixing
Step 1.
Attach the frontal xings to the drawer
frontal using 3 x 15mm screws per bracket
using the screw hole positions as shown.
50mm 50mm
68mm 68mm
100mm 100mm
Standard
Drawer
38.5mm 38.5mm
Step 2.
Attach the drawer front by
pushing the frontal onto the
sides, aligning the mechanism
with the xings.
Step 4.
Fit drawer cover caps over drawer side adjustment screws. Cover caps
Drawer
underside view
Drawer
inside view
Step 3. Drawer frontal adjustment
A. Loosen top screw. Turn the bottom screw to adjust drawer frontal height, once in desired position re-tighten the
top screw.
B. Press in the xing clips half way, located at the bottom of the frontal on both sides of the drawer. Adjust the
position of the drawer frontal, left or right. Release the frontal xing clips on both sides of the drawer to secure the
frontal in the new position.
B.
2.1.
A.

Page 4
For Internal Use: FI.WR.INS.076_WKIN0066_Drawer_ReplaceFRTL_Rev6
GRASS DEEP DRAWER
Drawer
side
Step 1.
Attach the frontal xings standard and deep to the draw frontal
using 5 x 15mm screws using the screw hole positions as shown.
Drawer
frontal
Drawer front
xing standard
Drawer
front xing
deep
Deep
fixing
Drawer
frontal
Step 2.
Attach the drawer front by pushing
the frontal onto the sides, aligning the
mechanism with the xings.
Step 4.
Fit drawer cover caps over drawer side adjustment.
Step 3. Drawer frontal adjustment
A. Loosen top two screws. Turn the bottom screw to adjust frontal height, once in desired position re-tighten the
top screws.
B. Turn the screw to adjust rear elevation of the drawer.
C. Press in the xing clips half way, located at the bottom of the frontal on both sides of the drawer. Adjust the
position of the drawer frontal, left or right. Release the frontal xing clips on both sides of the drawer to secure the
frontal in the new position.
Deep drawer
Drawer
Front Fixing
Standard
Drawer
Front Fixing
Standard
Drawer
Front
Fixing Deep
Drawer
Front
Fixing Deep
100mm 100mm
164mm 164mm
196mm 196mm
68mm 68mm
50mm 50mm
38.5mm 38.5mm
A. B. C.
Drawer
frontal
Drawer
side Drawer
side
Drawer
underside view
Drawer
back
Cover caps

Page 5
FRONTALS
Drawer Frontal Replacement Guide
Step 3. Glass Panel Attachment
Push the button in on the back of the drawer side. Slide the glass panel into the opening at the back of the drawer
side. Push the glass panel forwards into the opening at the front until you hear a click.
Drawer
front fixing
standard
Drawer
front fixing
deep
Step 2.
Attach the drawer front by pushing
the frontal onto the sides, aligning the
mechanism with the xings.
Step 1.
Attach the frontal xings standard and deep to the draw frontal
using 5 x 15mm screws using the screw hole positions as shown.
Deep drawer
Drawer
Front Fixing
Standard
Drawer
Front Fixing
Standard
Drawer
Front
Fixing Deep
Drawer
Front
Fixing Deep
100mm 100mm
164mm 164mm
196mm 196mm
68mm 68mm
50mm 50mm
38.5mm 38.5mm
Drawer
side
Drawer
frontal
Deep
Fixing
Drawer
frontal
GRASS GLASS DRAWER

Page 6
For Internal Use: FI.WR.INS.076_WKIN0066_Drawer_ReplaceFRTL_Rev6
GRASS GLASS DRAWER
Step 4. Drawer frontal adjustment
A. Loosen top two screws. Turn the bottom screw to adjust frontal height,
once in desired position re-tighten the top screws.
B. Turn screw to adjust rear elevation of drawer.
Step 6.
Fit drawer cover caps over drawer side adjustment screws.
5A.
Press in the xing clips half way,
located at the bottom of the frontal
where they meet the runners on
both sides of the drawer.
5B.
Adjust the position of the drawer
frontal, left or right.
5C.
Release the frontal xing clips
on both sides of the drawer to
secure the frontal in the new
position.
Step 5.
Adjust the frontal horizontally
Drawer
Frontal
Cover caps
A. B.
Drawer
Back
DrawerDrawer
sideside
DrawerDrawer
sideside

Page 7
FRONTALS
Drawer Frontal Replacement Guide
Step 2.
In one smooth motion, lift the front of the drawer,
this will disconnect the runner from the connectors
on the base of the drawer.
Once properly separated a click will be heard and
the drawer will be separate from the runner.
If this motion is not done with enough force then
the drawer may need to be lifted again.
Be careful not to lift the runners whilst lifting
the drawer.
Step 3.
The drawer is free to remove from the unit
Simply remove the loose drawer from the unit,
making sure not to damage the unit in the
process.
Step 1.
Open the drawer that is required to be removed.
Pull out the drawer until the runners are at full
extension.
TM DRAWER BOX REMOVAL
Removing a drawer is the same process for
Standard, Mid, Deep and Glass Drawers

Page 8
For Internal Use: FI.WR.INS.076_WKIN0066_Drawer_ReplaceFRTL_Rev6
Step 1.
Fully extend the drawer runners out of the unit
(for the drawer you are inserting).
Step 3.
Once the drawer is placed onto the runners,
pull forward the protruding lips on the ends
of the runners until a click is heard. Once the
click is heard the drawer is properly located and
secured to the runner.
Push the drawer back into the Unit.
Step 2.
Place the drawer onto the runners, making sure
that the groove of the drawer sides and the
runner mechanism are aligned.
TM DRAWER BOX INSERTION
Inserting a drawer is the same process for
Standard, Mid, Deep and Glass Drawers

Page 9
FRONTALS
Drawer Frontal Replacement Guide
TM STANDARD DRAWER
Drawer
front
Drawer side
Drawer side
xing clip
DRAWER FRONTAL ADJUSTMENT
Screw point 1as shown to adjust
drawer frontal left & right.
Releasing xing clip.
Screw point 3whilst applying
downward pressure as shown
to release.
Screw point 2a as shown to adjust
drawer frontal up & down.
Tighten 2b once in position.
12b 2a
3
Fixing clip
Step 2.
Push t drawer side xing clips onto drawer side.
Step 1.
Secure drawer side xing clips using 2 x 21mm screws in
pilot holes provided as shown below.
99mm
67mm
99mm
67mm
Standard
Drawer
36.5mm
36.5mm
Step 3.
Fit drawer cover caps over drawer side adjustment.
See page 14 for more details.
Drawer cover cap