Wren Kitchens Vogue BASE UNIT 300 1 Door User manual

BASE UNIT
300 - 600 1 Door Assembly Guide
For Internal Use: FI.WR.INS.020_WKIN00102_BASE_300-600_1Dr_Rev7.indd
350
600 600 Bin
450 500
400
300

Page 1
BASE UNIT
300 - 600 1 Door Assembly Guide
(F) x12
Wooden Dowel
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x7
30mm
Screw
(L) x28
15mm
Screw
(N) x1
Door Buer
(Z) x4
Shelf Peg Plastic
(M) x4
Cover
Cap
Panel B
x2 End Panel
Panel C
x1 Base Panel
Panel E
x2 Rail
Shelf
x1
Legs
x4
Frontal
(Packed separately)
x1
Panel A
x1 Back Panel
REQUIRED TOOLS
NOT to be
used with CAM
DOWEL & CAM
LOCK
L Bracket
x2
Hinge Mounting Plate
x2 Inc Screws
Hinge
x2 Inc Screws
(not used with Bins)
Space Plug
x1
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.020_WKIN00102_BASE_300-600_1Dr_Rev7.indd
All Cam Locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening. Do not use power tools with
Cam Dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
GG
GG
G
G
G
G
FF
F
F
F F
F
F
FF
FF
B
B B
B
C
E
E
B
B
View from underside View from underside
H
G
G
H
Step 1.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Seat (G)
Cam Dowel
into hole as
shown.
Step 3.
Attach panels (C) to panels (B),
using cam dowel (G) (in blue), and
also using dowels (F) (in orange)
in positions as shown.
Step 4.
Insert cam lock (H).
Do NOT tighten until Step 6.

Page 3
BASE UNIT
300 - 600 1 Door Assembly Guide
For the Bin Installation,
Back panel (A) should not be installed
(Skip Steps 5 to 7).
Step 5.
Slide back panel (A) into groove of end
panels (B).
Once back panel (A) is in position, ensure the
panel is ush & square with bottom of end
panels (B).
Step 6.
Hand tighten all cam locks (H), this will expand
cam dowels (G) and tighten the unit together.
Step 7.
Ensure unit is square. Secure back panel (A)
with 3 x 30mm screws (K) equally spaced at the
bottom of back panel (A) into base panel (C), as
shown.
Ensure you screw into the centre of base
panel (C) (9mm from the edge).
B
B
B
C
A
EE
E
A
C
K
K
K
9mm

Page 4
For Internal Use: FI.WR.INS.020_WKIN00102_BASE_300-600_1Dr_Rev7.indd
Step 9.
Secure each of the legs into place with
4 x 15mm screws (L) per leg.
B
B
Front
Front
C
Step 8.
Position legs as shown. Ensure legs are rotated to also
provide support to the end panels (B).
L
L
L
L
B
B
C
C
Step 10.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning unit
upright. Once in situ level accordingly.
Leg position diagram

Page 5
BASE UNIT
300 - 600 1 Door Assembly Guide
600 Bin
600 Bin Unit
Please refer to separate instructions included with your 600 bin.

Page 6
For Internal Use: FI.WR.INS.020_WKIN00102_BASE_300-600_1Dr_Rev7.indd
Securing to Adjacent Units
Screw into any side units using the 30mm screws (K) provided to secure to unit. Screw
just to the rear of the hinge plate at the top and bottom of both sides of the unit, place a
cover cap (M) on the head to conceal it.
L Brackets
Use 2 x 15mm screws (L) to secure each of the L brackets
to the unit at either side. Then screw up through into the
worktop as shown.
Worktop
Screw up through the front rail into your worktop to secure it in place.
Secure Unit to Wall
Using Space-Plug. Drill 1 pilot hole through the back brace into the wall and insert
wall plug. Then unwind space plug until it contacts both surfaces. Finally, tighten the
screws.
LL
Step 11.
Attach hinge mounting plate onto end panels (B) as shown, using
screws which are positioned within the hinge plates.
Hinge side or sides to be mounted in accordance to Customer
Specic Kitchen Plan.
K
126mm
126mm
94mm
94mm
B
From Bottom
From top
Screws for attaching to walls and worktop are not provided as these vary depending on materials,
thickness and construction. Ensure appropriate xings for wall and worktop construction are used.
Please refer to the specialist worktop supplier if these are required for solid surface worktops.

Page 7
BASE UNIT
300 - 600 1 Door Assembly Guide
The following steps are not required for bin units.
Step 12.
Insert hinge in top & bottom
holes as shown below.
Step 13.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 14.
Attach the door to unit
where required.
To attach door, clip hinge
onto hinge plate and click
to secure.
Hinge Cover Caps
Step 16.
Fit cover caps to hinge.
Adjust Soft close to suit.
Step 15.
Adjust hinge to suit. As shown below.
To adjust hinge using
a screw driver, tighten
or loosen as required at
points 1 & 2.
Point 1- In - Out
Point 2- Left - Right
12
FRONTAL
HINGE
ADJUSTMENT
Hinge Plates
View from inside of Unit
To release door,
pull catch as shown,
to release hinge from
the hinge plate.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
To Move the
hinge up/down,
loosen screws
A + B,
Manoeuvre
the door, then
re-tighten the
screws
A
B