Wren Kitchens WALL UNIT 672 L Corner User manual

WALL UNIT
672 L Corner Assembly Guide
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr.Rev6

Page 1
WALL UNIT
672 L Corner Assembly Guide
Panel A
x1 Back Panel
Panel S
x1 Back Panel
Hanging Bracket
X3 Inc Screws
(F) x16
Wooden
Dowel
REQUIRED TOOLS
NOT to be
used with CAM
DOWEL & CAM
LOCK
(G) x8
Cam Dowel
(Expanding)
(W) x8
Cam Dowel
(H) x16
Cam Lock
(K) x4
30mm
Screw
(L) x8
15mm
Screw
(P) x8
45mm
Screw
(S) x6
20mm
Screw
(M) x4
Cover Cap
(N) x2
Door
Buer
(Z) x12
Shelf Peg
Plastic
(T) x10
Back Panel
Support Clip
Hanging Bracket
Plate X3 (Screws Not
Included)
Hinge Mounting Plate
X4 Inc Screws
Hinge
X4 Inc Screws
Corner
Gusset
X2
Hanging
Bracket
Cover Cap
X3
Panel B
x2 End Panel
Panel C
x2 Fixed Shelf
(Top & Bottom)
Panel D
x2 Fixed Shelf
Loose Shelf
x2 Large
Loose Shelf
x2 Small
Corner Post
x1
(packed
separately)
Frontal
(packed
separately)
x2
(U) Fixing
Plate
X2
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr.Rev6
Step 3.
Attach panels x2 (C) to panel
(B), using cam dowels (G)
(in blue),and also using
dowels (F) (in orange) in
positions as shown.
Step 4.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and tighten
the unit together.
All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening. Do not use power tools with
cam dowel (G) or cam lock (H)
B
C
C
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B
View from underside
B
C
G
GC
H
H
View from underside
Step 1.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Seat (G)
cam dowel
into hole as
shown.

Page 3
WALL UNIT
672 L Corner Assembly Guide
Step 5.
Seat dowel (F)
into holes in
both panels (B)
as shown. Step 6.
Seat expanding
cam dowel (G) into
holes in
both end panels (B)
as shown.
Step 7.
Attach panel (B) to
panels (D) using cam
dowels (G) (in blue)
and also using dowels
(F) (in orange) in
positions as shown.
All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening. Do not use power tools with
cam dowel (G) or cam lock (H)
B
D
D
Seat (G)
Cam Dowel
into hole as
shown.
Step 8.
Insert cam lock (H).
Hand tighten all cam locks (H), this
will expand the cam dowels (G) and
tighten the unit together.
View from underside
B
CC
H
H
G
G
View from underside
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B

Page 4
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr.Rev6
Step 9.
Seat dowel (F) into holes
in both panels (D) as
shown.
Step 10.
Seat cam dowel (W)
into holes in panel (D)
as shown.
Step 12.
Insert and hand tighten
all cam locks (H).
Step 11.
Attach panels x 2 (D) to panels (C)
using cam dowels (W) (in blue) and
also using dowels (F) (in orange) in
positions as shown.
All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
B
C
D
D
C
C
C
D
C
H
HBB
D
D
Seat (W)
Cam Dowel
into hole as
shown.
W
W
FF

Page 5
WALL UNIT
672 L Corner Assembly Guide
B
C
S
Step 13.
Slide back panel (S) into groove of panels (C).
Step 14.
Slide back panel (A) into groove of side panel (B)
while also allowing panel (S) slide into the groove
of panel (A).
Step 16.
Slide 9 x back panel clips
(T) into the groove of both
panels (A), (B) & (C).The
back panel clips (T) should
be evenly spaced as shown
and positioned to allow the
hanging bracket and corner
gussets to be tted. Once
in place, tighten screw.
Step 15.
Ensure all panels are
square. Screw back
panel (A) to panels (C)
& (D) with 8 x screws
(P) using provided pilot
holes.
T
A
T
A
B
C
A
S
P
S
A
C
D

Page 6
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr.Rev6
A
B
A
A
Step 18.
Secure corner
gussets to the
bottom left and
right hand side
of the wall unit
using 4 x 15mm
screws (L) per
plate.
Step a
Insert hanging
bracket into pre-drilled holes
Step c
Secure with provided
2 x 20mm screws (S) per bracket
Step b
Rotate locking
lever 180 degrees
Detail A Detail A
S
S
Detail A
View through
Back Panel
Pilot
hole
M
Detail B
L
L
LL
Detail B
Step 19.
Drill a small pilot hole through the centre of the corner gussets,
through the back panel. Use this hole at the end of the process
to screw through and into the wall. Cover the screw heads using
the cover caps (M) provided.
Step 17. Hanging Brackets steps a,b & c to be carried out on both sides as shown
Care to be taken. Hanging procedure is necessary for a safe installation.
Screws for attaching to walls are not provided as these vary depending on materials,
thickness and construction. Ensure appropriate xings for wall construction are used.

Page 7
WALL UNIT
672 L Corner Assembly Guide
K
Step 20.
Measure appropriately and attach the 3 x hanging bracket plates onto the wall screwing through the provided holes
into your wall.
Step 21.
Hang the unit using the brackets to
hook onto the plate as shown
Hanging Bracket
Plate
Step a.
Rotate the screw clockwise
to move the unit up.
Anti-clockwise for down.
Step b.
Adjust the depth using
centre screw.
Step c.
Screw the red screw until
it touches the plate to
lock in position.
b
c
a
Hanging
Bracket
viewed through
Back Panel
C
a
b
Step 23.
Screw into any side units using the provided 2 x 30mm screws (K) to secure the
unit. Screw just to the rear of the hinge plate then place a cover caps (M) on the
head to conceal it.
Screws for attaching to walls are not provided as these vary depending on materials,
thickness and construction. Ensure appropriate xings for wall construction are used.
Step 22.
Using points a, b & c adjust the unit
to suit.

Page 8
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr.Rev6
Step 24.
Align corner post to frontal. Equally space 2 x xing
plates (U) to the back of frontal & corner post. Ensure a 4
mm gap is maintained between frontal & post once xed
together. Screw in place using 4 x 15mm screws (L) per
xing plate (U).
U
U
L
L
L
L
L
L
L
L
Step 25.
Insert hinge in top & bottom holes as shown
below.
Step 26.
Secure hinges by
tightening
2 x screws with hinge
dowels attached. These
are already positioned
within the hinges.
Step 27.
Attach the door to unit
where required. To attach
door, clip hinge onto hinge
plate and click to secure.
Hinge Cover Caps
Step 29.
Fit cover caps to hinge.
Adjust Soft close to suit.
Step 28.
Adjust hinge to suit. As shown below.
To adjust hinge using
a screw driver, tighten
or loosen as required at
points 1& 2.
Point 1 - In - Out
Point 2- Left - Right
12
FRONTAL
HINGE
ADJUSTMENT
Hinge Plates
View from inside of unit
To release door,
pull catch as shown,
to release hinge from
the hinge plate.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
To Move the
hinge up/down,
loosen screws
A + B,
Manoeuvre
the door, then
re-tighten the
screws
A
B

Page 9
WALL UNIT
672 L Corner Assembly Guide

Page 10
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr.Rev6