Wren Kitchens 200 Tall User manual

WALL UNIT
150 - 600 Tall 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.045_WKIN00130_WALL_150-600_Tall_1Dr_Rev5.indd
150 Tall
400 Tall
300 Tall
450 Tall
600 Tall
350 Tall
500 Tall
200 Tall

WALL UNIT
150 - 600 Tall 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.045_WKIN00130_WALL_150-600_Tall_1Dr_Rev5.indd
Page 1
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Panel A
x1 Back Panel
HANGING BRACKET
x2 Inc Screws
(F) x8
Wooden Dowel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x2
30mm
Screw
(L) x8
15mm
Screw
(S) x4
20mm
Screw
(M) x2
Cover Cap
(N) x1
Door
Buer
(Z) x12
Shelf Peg
Plastic
(T) x10
Back Panel
Support Clip
HANGING BRACKET PLATE
x2 (Screws NOT included)
HINGE MOUNTING PLATE
x2 Inc Screws
HINGE
x2 Inc Screws
CORNER
GUSSET
x2
HANGING BRACKET
COVER CAP
x2
Panel B
x2 End Panel
Panel C
x2 Base Panel
Frontal
(packed separately)
x1
Loose Shelf
x2

WALL UNIT
150 - 600 Tall 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.045_WKIN00130_WALL_150-600_Tall_1Dr_Rev5.indd
Page 2
B
Step 1.
Seat dowel (F)
into holes in end
panel (B)
as shown.
Step 2.
Seat cam dowel (G)
into holes in end panel
(B) as shown.
Step 3.
Attach panels x2 (C) to
panel (B), using cam
dowels (G)
& cam locks (H) (in blue),
and also using dowels (F)
(in orange) in positions as
shown.
Step 4.
Slide panel (A) into the
groove of panels (B) and
x 2 panels (C).
Step 5.
Insert cam lock (H).
Hand tighten all
cam locks (H), this
will expand the
cam dowels (G) and tighten
the unit together.
NB. All Cam Locks (H) are to be positioned facing the
outside of the unit Carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
B
A
C
C
G
G
F
F
F
F
G
G
Seat (G)
cam dowel
into hole as
shown.
View from underside
B
CC
H
H
G
G
View from underside

WALL UNIT
150 - 600 Tall 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.045_WKIN00130_WALL_150-600_Tall_1Dr_Rev5.indd
Page 3
B
G
G
F
F
F
F
G
G
Step 6.
Seat dowel (F) into holes in
both panels (B) as shown.
Step 7.
Seat cam dowel (G) into holes in
both end panels (B) as shown.
Step 8.
Attach panel (B) to panels
(C) using cam dowels (G)
& cam lock (H) (in blue)
and also using dowels (F)
(in orange) in positions as
shown. Ensure panel (A) is
seated into the groove of
panel (B).
Step 9.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and tighten
the unit together.
NB. All Cam Locks (H) are to be positioned facing the
outside of the unit Carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
B
A
C
C
Dowel (F)
& Cam Dowel (G)
location detail
Seat (G)
cam dowel
into hole as
shown.
View from underside
B
CC
H
H
G
G
View from underside

WALL UNIT
150 - 600 Tall 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.045_WKIN00130_WALL_150-600_Tall_1Dr_Rev5.indd
Page 4
Step 11.
Slide the back panel clips (T) into the groove of both
panels (B) & (C)s. The back panel clips (T) should be
evenly spaced as shown and positioned to allow the
hanging bracket and corner gussets to be tted. Once
in place, tighten screw.
Step 10.
Ensure Carcase is
square.
B
A
A
A
C
T
T
126mm
126mm
94mm
94mm
from top
from base
Step 12.
Attach hinge mounting plates
onto both end panels (B) in
locations shown using screws
(L) which are already positioned
within the hinge plates.

WALL UNIT
150 - 600 Tall 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.045_WKIN00130_WALL_150-600_Tall_1Dr_Rev5.indd
Page 5
Step a
Insert Hanging
Bracket into pre-drilled holes
Step 13.
Hanging Brackets steps a,b & c to be carried out on both
sides as shown
Step c
Secure with provided
2 x 20mm screws (S) per bracket
Step b
Rotate locking
lever 180 degrees
Step 14.
Secure Corner Gussets
to the bottom left and
right hand side of the
wall unit using
4 x 15mm screws (L)
per plate.
L
L
L
L
Detail B
View though
Back Panel
Pilot
hole
M
Detail B
A
B
Step 15.
Drill a small pilot hole through the centre of the Corner Gussets.
Use this hole at the end of the process to screw through and
into the wall. Cover the screw heads using the cover caps (M)
provided.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction. Ensure
appropriate xings for wall constructions are used.
S
S
Detail A Detail A Detail A
Care to be taken. Hanging procedure
is neccesary for a safe installation.

WALL UNIT
150 - 600 Tall 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.045_WKIN00130_WALL_150-600_Tall_1Dr_Rev5.indd
Page 6
Step 16.
Measure appropriately and attach the 2 x hanging bracket plates onto the
wall screwing through the provided holes into your wall.
Screws for xing to walls are not provided as these vary depending
on your wall material and construction. Ensure appropriate xings for
wall construction are used.
Step 17.
Hang the cabinet using
the brackets to hook
onto the plate as shown
Step 18.
Using points a, b & c adjust the Cabinet to suit.
Step 19.
Screw into any side units using the
provided 2x 30mm screws (K) to
secure the unit. Screw just to the
rear of the hinge plate then place a
cover cap on the head to conceal it.
Step a.
Rotate the screw clockwise
to move the cabinet up.
Anti-clockwise for down.
Step b.
Adjust the depth
using centre
screw.
Step c.
Screw the red screw until it
touches the plate to lock
in position.
Hanging Bracket
Plate
b
c
a
K
Hanging
Bracket
viewed though
Back Panel
C
a
b

WALL UNIT
150 - 600 Tall 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.045_WKIN00130_WALL_150-600_Tall_1Dr_Rev5.indd
Page 7
Step 20.
Insert hinge in top & bottom
holes as shown.
Step 21.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 22.
Attach the door to unit
where required.
To attach door
clip hinge onto hinge
plate and click to secure.
Step 23.
Adjust hinge to suit. As shown below. Hinge Mounting Plates
Hinge Cover Caps
View from Inside of Carcass
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1- In - Out
Point 2- side - side
12
FRONTAL HINGE
ADJUSTMENT
To Release door
Pull catch as shown,
to release hinge
from the hinge
plate.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
Step 24.
Fit cover caps to hinge.
Adjust Softclose to suit.