Wren Kitchens Vogue BASE UNIT 150 Pull Out User manual

BASE UNIT
150 - 300 Pull Out Assembly Guide
For Internal Use: FI.WR.INS.029_WKIN00101_BASE_PullOut_150-300_1Dr_Rev6.indd
150 Pull Out
300 Pull Out

Page 1
BASE UNIT
150 - 300 Pull Out Assembly Guide
(F) x8
Wooden
Dowel
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x6
30mm
Screw
(L) x20
15mm
Screw
(N) x1
Door
Buer
(J) x6
16mm
Runner
Screw
(X) x8
19mm
Screw
(M) x4
Cover
Cap
Panel A
x1Back Panel
Panel C
x2 Base Fixed Panel
Legs
x4
Frontal
(Packed separately)
x1
Panel B
x2 End Panel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
L Bracket LGE
x2
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.029_WKIN00101_BASE_PullOut_150-300_1Dr_Rev6.indd
Step 3.
Attach panels (C) to panels (B),
using cam dowel (G) (in blue), and
also using dowels (F) (in orange) in
positions as shown.
Step 4.
Insert cam lock (H).
Do NOT tighten until Step 6.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening. Do NOT use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
G
G
G
G
G
G
G
G
F
F
F
F
F
F
F
F
B B
B
B
View from underside View from underside
H
G
G
H
Step 1.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Seat (G)
cam dowel
into hole as
shown.

Page 3
BASE UNIT
150 - 300 Pull Out Assembly Guide
Step 5.
Slide back panel (A) into
groove of end panels (B).
Once back panel (A) is in position, ensure
the panel is ush & square with bottom
of end panels (B).
Step 6.
Ensure unit is square.
Hand tighten all cam locks (H), this will
expand cam dowels (G) and tighten the
unit together.
Step 7.
Secure back panel (A) with 2 x 30mm
screws (K) equally spaced at the top &
bottom of back panel (A) into both xed
panels (C), as shown.
Ensure you screw into the centres of the
base panels (C) (9mm from the edge).
B
C
A
B
A
C
K
K
B
9mm
9mm

Page 4
For Internal Use: FI.WR.INS.029_WKIN00101_BASE_PullOut_150-300_1Dr_Rev6.indd
Step 9.
Secure each of the legs into place with 4 x 15mm screws
(L) per leg.
B
B
Front
Front
C
Step 8.
Position legs as shown. Ensure legs are
rotated to also provide support to the end
panels (B).
L
L
L
L
B
B
C
Step 10.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning unit upright. Once in situ
level accordingly.
Leg position diagram
View from front
View from Back

Page 5
BASE UNIT
150 - 300 Pull Out Assembly Guide
Pull Out Pack
Please refer to separate installation instructions
included with your pull out contents.
For Step 1 in pull
out instructions.
Use 16mm screws.
For Step 2 in pull
out instructions.
Use 16mm screws.
For Step 4 in pull out instructions.
Use 16mm screws.
Step 1 of pull out
instructions
Step 2 of pull out
instructions
Step 4 of pull out
instructions
Step 4 of pull out
instructions
150 Pull Out
300 Pull Out

Page 6
For Internal Use: FI.WR.INS.029_WKIN00101_BASE_PullOut_150-300_1Dr_Rev6.indd
Worktop
Screw up through panel (C) into your worktop to secure it in place.
Screw to Adjacent Unit
Screw through side panels (B) where appropriate, into any side units,
using the 30mm screws (K) provided to secure to unit. Place a cover cap
(M) on the head to conceal it.
L Brackets
Where applicable, secure unit to the wall using 2 x 15mm
screws (L) to secure each of the L brackets LGE to the units
at either side. Then screw through into the wall as shown.
L
L
C
K
Screws for attaching to walls and worktop are not provided as these vary depending on materials,
thickness and construction. Ensure appropriate xings for wall and worktop construction are used.
Please refer to the specialist worktop supplier if these are required for solid surface worktops.