Wren Kitchens Vogue BASE UNIT 800 2 Door User manual

BASE UNIT
700 - 800 2 Door Assembly Guide
For Internal Use: FI.WR.INS.021_WKIN00103_BASE_700-800_2Dr_Rev6.indd
700
800

Page 1
BASE UNIT
700 - 800 2 Door Assembly Guide
REQUIRED TOOLS
NOT to be
used with CAM
DOWEL & CAM
LOCK
(F) x12
Wooden
Dowel
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x8
30mm
Screw
(L) x32
15mm
Screw
(N) x2
Door Buer
(Z) x5
Shelf Peg
Plastic
(M) x4
Cover Cap
Panel B
x2 End Panel
Panel D
x2 Rail
Panel C
x1 Base Panel
Shelf
x1
Legs
x5
Frontal
(Packed separately)
x2
Panel A
x1 Back Panel
(800 only folded)
L Bracket
x2
Hinge Mounting Plate
x4 Inc Screws
Hinge
x4 Inc Screws
Space Plug
x2
(J) x4
45mm
Screw Black
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.021_WKIN00103_BASE_700-800_2Dr_Rev6.indd
Step 1.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening. Do NOT use power tools with
cam dowel (G) or cam lock (H)
B
B
C
D
B
B
View from underside View from underside
H
G
G
H
D
Dowel (F)
& Cam Dowel (G)
location detail
G G
G G
G GF F
F
F F
FFF F
BB
F
GFFG
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Seat (G)
cam dowel
into hole as
shown.
Step 3.
Attach panels (C) to panels (B),
using cam dowel (G) (in blue), and
also using dowels (F) (in orange)
in positions as shown.
Step 4.
Insert cam lock (H).
Do NOT tighten until Step 6.

Page 3
BASE UNIT
700 - 800 2 Door Assembly Guide
(800 used as reference image)
Step 5.
Slide back panel (A) into
groove of end panels (B).
Once back panel (A) is in position, ensure the
panel is ush & square with bottom of
end panels (B).
Step 6.
Hand tighten all cam locks (H), this will
expand cam dowels (G) and tighten the
unit together.
Step 7.
Ensure unit is square. Secure back panel (A)
with 4 x 30mm screws (K) equally spaced at the
bottom of back panel (A) into base panel (C), as
shown.
Ensure you screw into the centre of the base
panels (C) (9mm from the edge).
B
D
C
A
K
B
C
A
9mm
D

Page 4
For Internal Use: FI.WR.INS.021_WKIN00103_BASE_700-800_2Dr_Rev6.indd
(800 used as reference image)
Leg position diagram
C
BB
Front Front
Step 9.
Secure each of the legs into place with 4 x 15mm screws (L)
per leg.
Step 8.
Position legs as shown. Ensure legs are
rotated to also provide support to the
end panels (B).
L
L
L
L
B
C
B
Step 10.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning unit upright. Once in situ
level accordingly.
C

Page 5
BASE UNIT
700 - 800 2 Door Assembly Guide
Securing to Adjacent Units
Screw into any side units using the 30mm screws (K) provided to secure to unit.
Screw just to the rear of the hinge plate at the top and bottom of both sides of the
unit, place a cover cap (M) on the head to conceal it.
Step 11.
Attach hinge mounting plate onto both End Panels (B) as
shown, using screws which are already positioned within the
hinge plates.
Hinge side or sides to be mounted in accordance to
Customer Specic Kitchen Plan.
Worktop
Screw up through the front rail into your worktop to secure it in place.
LL
Space Plugs
Secure unit to wall using space plugs. Drill 2 pilot holes through the back rail into the
wall and insert wall plug. Then unwind space plug until it contacts both surfaces. Finally,
tighten the screws.
L Brackets
Use 2 x 15mm screws (L) to secure each of the L brackets
to the unit at either side. Then screw up through into the
worktop as shown.
126mm
126mm
94mm
94mm
B
From Bottom
From Top
Hinge Plates
K
Screws for attaching to walls and worktop are not provided as these vary depending on materials,
thickness and construction. Ensure appropriate xings for wall and worktop construction are used.
Please refer to the specialist worktop supplier if these are required for solid surface worktops.

Page 6
For Internal Use: FI.WR.INS.021_WKIN00103_BASE_700-800_2Dr_Rev6.indd
Step 12.
Insert hinge in top & bottom
holes as shown below.
Step 13.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 14.
Attach the door to unit
where required.
To attach door, clip hinge
onto hinge plate and click
to secure.
Hinge Cover Caps
Step 16.
Fit cover caps to hinge.
Adjust Soft close to suit.
Step 15.
Adjust hinge to suit. As shown below.
To adjust hinge using
a screw driver, tighten
or loosen as required at
points 1 & 2.
Point 1- In - Out
Point 2- Left - Right
12
FRONTAL
HINGE
ADJUSTMENT
Hinge Plates
View from inside of unit
To release door,
pull catch as shown,
to release hinge from
the hinge plate.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
To Move the
hinge up/down,
loosen screws
A + B,
Manoeuvre
the door, then
re-tighten the
screws
A
B