Wren Kitchens Vogue BASE UNIT 1000 2 Door User manual

BASE UNIT
1000 2/3 Drawer Assembly Guide
For Internal Use: FI.WR.INS.027_WKIN00111_BASE_1000_2_3Drawer_Rev7.indd
1000
2 Drawer
1000
3 Drawer

Page 1
BASE UNIT
1000 2/3 Drawer Assembly Guide
Standard Drawer (Packed Separately)
Fitting Pack Contents
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
DRAWER
COVER CAP
x2
DRAWER
COVER CAP
x2
DRAWER SIDE
x1 Right Hand
DRAWER SIDE
x1 Right Hand
DRAWER SIDE
x1 Left Hand
DRAWER SIDE
x1 Left Hand
DRAWER
FRONT
FIXING
x 2
DRAWER
FRONT
FIXING
x 2
Deep Drawer (Packed Separately)
Fitting Pack Contents
(Y) x2
Gallery
Head
(J) x16
Drawer Runner
16mm Screws
(J) x16
Drawer Runner
16mm Screws
(N) x1
Door Buer
(N) x1
Door Buer
(Q) x4
21mm
Screw
(Q) x4
21mm
Screw
(L) x2
15mm
Screw
METAL BACK
PANEL
x 1
METAL BACK
PANEL
x 1
DRAWER
BASE
x 1
DRAWER
BASE
x 1
DRAWER
RUNNER
x 1 Right Hand
DRAWER
RUNNER
x 1 Right Hand
FRONTAL
(Supplied separately)
FRONTAL
(Supplied separately)
DRAWER
RUNNER
x 1 Left Hand
DRAWER
RUNNER
x 1 Left Hand
GALLERY
RAIL
x 2
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.027_WKIN00111_BASE_1000_2_3Drawer_Rev7.indd
99mm
67mm
99mm
67mm
Step 2.
Clip on metal back panel to drawer base &
drawer sides.
Step 3.
Screw back panel in position using 2 x 16mm screws (J)
to drawer base in holes provided.
Step 1.
Secure drawer base to drawer side using 4 x 16mm
drawer runner screws (J) in holes provided.
Seat the edge of drawer base tight
into corner of casing, as shown.
The decorative face of drawer base
to be positioned as shown.
Metal back
panel
View from back
Metal
back
panel
Drawer base
white
decorative
face up
J
J
J
J
J
J
J
J
J
Front of drawer
Decorative
face
Drawer
base
J
Step 4.
Frontal Attachment
Secure drawer side xing clips using 2 x 21mm
screws (Q) in pilot holes provided as shown.
Drawer
base
Fixing
clip
& (Q)
Fixing
clip
& (Q)
Standard
drawer
Step 6.
Fit Drawer Cover Caps
over drawer side adjustment.
Drawer
Cover Cap
Drawer
frontal
Drawer side
J
Fixing
clip
Drawer side
xing clip
Q
Q
Drawer
frontal
Repeat step 1 so both drawer
sides are attached to drawer base.
View of drawer side
1
3
2b
2a
Step 5.
Draw Adjustment
Screw point 1as shown
to adjust drawer
frontal right & left.
Screw point 2a as
shown to adjust
drawer frontal
up & down.
Tighten 2b
once in position.
Releasing xing clip. Screw
point 3whilst applying
downward pressure as
shown to release.

Page 3
BASE UNIT
1000 2/3 Drawer Assembly Guide
Fixing
clip
& (Q)
Fixing
clip
& (Q)
2
1
Y & L Y & L
Step 6.
Fit Gallery Rail into the top
corners of Metal Back Panel.
Locate front end of the
Gallery Rail into the opening
of the gallery Head, which
is secured to the frontal as
shown
Deep
drawer
J
J
Metal
back
panel
Drawer base
white decorative
face up
Fixing clip
(Y) Gallery
Head
Drawer side
xing clip
Q
Q
Drawer
frontal
Drawer side
Drawer
frontal
Step 7.
Fit Drawer Cover Caps
over drawer side adjustment.
Drawer
Cover Cap
Step 2.
Clip on metal back panel to drawer base &
drawer sides.
Step 3.
Screw back panel in position using 2 x 16mm screws (J)
to drawer base in holes provided.
Step 1.
Secure drawer base to drawer side using 4 x 16mm
drawer runner screws (J) in holes provided.
Seat the edge of drawer base tight
into corner of casing, as shown.
The decorative face of drawer base
to be positioned as shown.
View from back
Metal
back
panel
Front of drawer
Decorative
face
Drawer
base
J
J
JJ
JJ
Drawer
base
J
Repeat step 1 so both drawer
sides are attached to drawer base.
JJ
Step 5.
Draw Adjustment
Screw point 1as shown to
adjust drawer frontal
right & left.
Drawer Frontal
Adjustment
Screw point 2a
as shown to adjust
drawer frontal up & down.
Tighten 2b
once in position.
Releasing
xing clip.
Screw point 3
whilst applying
downward pressure
as shown to release. View of drawer side
13
2b
2a
Step 4.
Frontal Attachment
Secure drawer side xing clips using 2 x 21mm screws (Q)
&Gallery Head (Y) using 1 x 15mm screw (L) in pilot holes
provided as shown.

Page 4
For Internal Use: FI.WR.INS.027_WKIN00111_BASE_1000_2_3Drawer_Rev7.indd
Panel A
x1 Back Panel
Panel B
x2 End Panel
Panel E
x2 Rail Panel
Panel C
x1 Base Panel
(F) x12
Wooden Dowel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x7
30mm
Screw
(L) x30
15mm
Screw
L Bracket LGE
x2
Space Plug
x2
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
1000 Drawer Unit Contents

Page 5
BASE UNIT
1000 2/3 Drawer Assembly Guide
B
37mm 261mm
431mm
74mm
From Front
646mm
74mm
503mm
360mm
From Front
From Bottom
From Bottom
From Bottom
B
74mm
646mm
360mm
From Front
View from underside
2 drawer
4 drawer
600 units used as
reference
Step 1.
To attach drawer runner
screw into end panels (B)
using 2 x 16mm screws (J)
per drawer runner, into
pilot holes provided,
3rd hole from front,
as shown.
B
B
B
Drawer runner bracket screw position
JJ
J
J
3 drawer

Page 6
For Internal Use: FI.WR.INS.027_WKIN00111_BASE_1000_2_3Drawer_Rev7.indd
Step 4.
Attach panels (C) & (E) to panels (B),
using cam dowel (G)(in blue),and also
using dowels (F) (in orange) in positions
as shown.
Step 5.
Insert cam lock (H).
Do NOT tighten until Step 7.
NB. All Cam Locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
B
B
E
E
C
B
B
C
C
View from underside
H
G
G
View from underside
H
FFGFF
F
FF
F
G
G
GG FF FF
BB
GGG
Step 2.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 3.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Seat (G)
cam dowel
into hole as
shown.

Page 7
BASE UNIT
1000 2/3 Drawer Assembly Guide
Step 6.
Slide back panel (A) into groove of end panels
(B).
Once back panel (A) is in position, ensure the
panel is ush & square with bottom of end
panels (B).
Step 7.
Hand tighten all cam locks (H), this will expand
cam dowels (G) and tighten the unit together.
Step 8.
Ensure unit is square. Secure back panel (A)
with 4 x 30mm screws (K) equally spaced at the
bottom of back panel (A) into base panel (C), as
shown.
Ensure you screw into the centre of base panel
(C) (9mm from bottom edge).
B
C
A
B
E
B
C
K
K
K
K
A
9mm
E

Page 8
For Internal Use: FI.WR.INS.027_WKIN00111_BASE_1000_2_3Drawer_Rev7.indd
Leg position diagram
C
BB
Front Front
Step 10.
Secure each of the legs into place with 4 x 15mm screws (L)
per leg.
Step 9.
Position legs as shown. Ensure legs are
rotated to also provide support to the
end panels (B).
L
L
L
L
B
C
B
Step 11.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning unit upright. Once in situ
level accordingly.
C

Page 9
BASE UNIT
1000 2/3 Drawer Assembly Guide
Use 2 x 15mm screws (L) to secure each of the
L brackets to the unit at either side.
Then screw up through into the worktop as
shown.
Screw up through the front rail into your worktop to secure it in place.
L
L
Screw into any side units using the 30mm screws (K) provided to secure to
the unit. Screw just to the rear of the indentations at the top and bottom on
sides of the unit where applicable. Place a cover caps (M) on the head of the
screw to conceal it.
K
Screws for attaching to walls and worktop are not provided as these vary depending
on materials, thickness and construction. Ensure appropriate xings for wall and
worktop construction are used. Please refer to the specialist worktop supplier if
these are required for solid surface worktops.
Secure unit to wall using space plugs.
Drill pilot holes through the back brace into the wall
and insert wall plugs. Then unwind space plugs until it
contacts both surfaces.
Finally, tighten the screws.

Page 10
For Internal Use: FI.WR.INS.027_WKIN00111_BASE_1000_2_3Drawer_Rev7.indd