Wren Kitchens Vogue WALL UNIT 1000 Tall 2 Door User manual

WALL UNIT
1000 Tall 2 Door Assembly Guide
For Internal Use: FI.WR.INS.047_WKIN00132_WALL_1000_2Dr_Tall.Rev6
1000 Tall

Page 1
WALL UNIT
1000 Tall 2 Door Assembly Guide
HANGING BRACKET
x2 Inc Screws
(F) x8
Wooden
Dowel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x4
30mm
Screw
(P) x4
45mm
Screw
(L) x8
15mm
Screw
(S) x4
20mm
Screw
(M) x4
Cover Cap
(N) x2
Door
Buer
(Z) x10
Shelf Peg
Plastic
(T) x12
Back Panel
Support Clip
HANGING
BRACKET PLATE
x2 (Screws NOT included)
HINGE
MOUNTING PLATE
x4 Inc Screws
HINGE
x4 Inc Screws
CORNER
GUSSET
x2
HANGING BRACKET
COVER CAP
x2
Panel A
x1 Back Panel
Panel B
x2 End Panel
Panel C
x2 Base Panel
Frontal
(packed separately)
x2
Muntin D
x1
Loose
Shelf
x3
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.047_WKIN00132_WALL_1000_2Dr_Tall.Rev6
Step 1.
Seat dowel (F) into holes in
end panel (B) as shown.
Step 2.
Seat cam dowel (G)
into holes in end panel
(B) as shown.
Step 3.
Attach panels x2 (C) to panel
(B), using cam dowels (G)
(in blue) and also using
dowels (F) (in orange) in
positions as shown.
Step 4.
Slide panel (A) into the
groove of panels (B) and
x 2 (C).
NB. All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening. Do not use power tools with
cam dowel (G) or cam lock (H)
B
Dowel (F)
& Cam Dowel (G)
location detail
Seat (G)
Cam Dowel
into hole as
shown.
View from underside
B
CC
H
H
G
G
View from underside
G
G
F
F
F
F
G
G
B
Step 5.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and tighten
the unit together.
C
C
A
B

Page 3
WALL UNIT
1000 Tall 2 Door Assembly Guide
Step 6.
Seat dowel (F)
into holes in
both panels (B)
as shown. Step 7.
Seat cam dowel (G)
into holes in
both end panels (B)
as shown.
Step 8.
Attach panel (B) to panels
(C) using cam dowels (G)
(in blue) and also using
dowels (F) (in orange) in
positions as shown. Ensure
panel (A) is seated into the
groove of panel (B).
Step 9.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and tighten
the unit together.
NB. All cam locks (H) are to be positioned facing the outside
of the unit carcase, for ease of tightening.
B
B
A
C
C
Dowel (F)
& Cam Dowel (G)
location detail
Do not use power tools with
cam dowel (G) or cam lock (H)
Seat (G)
Cam Dowel
into hole as
shown.
View from underside
B
CC
H
H
G
G
View from underside
G
G
F
F
F
F
G
G
B

Page 4
For Internal Use: FI.WR.INS.047_WKIN00132_WALL_1000_2Dr_Tall.Rev6
BA
B
B
C
C
P
P
Step 10.
Ensure unit is square.
C
126mm
126mm
94mm
94mm
B
L
L
from base
from top
T
T
T
T
T
TT
TT
TT
Step 13.
Attach hinge mounting plates onto
end panels (B) in locations shown using
screws already in the hinge plates.
Hinge side or sides to be mounted
in accordance to Customer Specic
Kitchen Plan.
Step 11.
Slide the back panel
clips (T) into the groove
of both panels (B) & (A).
The back panel clips (T)
should be evenly spaced
as shown and positioned
to allow the hanging
bracket and corner
gussets to be tted.
Once in place, tighten
screw.
Step 12.
Join muntin panel (D), to both panels
(C) using 4 x 45mm screws (P) as
shown.
B
A
T
T
A
B
T

Page 5
WALL UNIT
1000 Tall 2 Door Assembly Guide
A
B
Step 15.
Secure corner gussets
to the bottom left and
right hand side of the
wall unit using 4 x 15mm
screws (L) per plate.
Step a
Insert hanging
bracket into pre-drilled holes
Step c
Secure with provided
2 x 20mm screws (S) per bracket
Step b
Rotate locking
lever 180 degrees
Detail A Detail A
S
S
Detail A
View through
Back Panel
Pilot
hole
M
Detail B
Step 14. Hanging Brackets steps a,b & c to be carried out on both sides as shown
Care to be taken. Hanging procedure is necessary for a safe installation.
L
L
L
L
Detail B
Step 16.
Drill a small pilot hole through the centre of the corner gussets,
through the back of the unit. Use this hole at the end of the
process to screw through and into the wall. Cover the screw
heads using the cover caps (M) provided.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction. Ensure
appropriate xings for wall constructions are used.

Page 6
For Internal Use: FI.WR.INS.047_WKIN00132_WALL_1000_2Dr_Tall.Rev6
K
Step 17.
Measure appropriately and
attach the 2 x hanging bracket
plates onto the wall screwing
through the provided holes into
your wall.
Step 18.
Hang the unit using the
brackets to hook onto the
plate as shown
Hanging Bracket
Plate
Step 19.
Using points a, b & c adjust the unit to suit.
Step a.
Rotate the screw clockwise
to move the unit up.
Anti-clockwise for down.
Step b.
Adjust the depth
using centre screw.
Step c.
Screw the red screw until it
touches the plate to lock
in position.
Hanging
Bracket
viewed through
Back Panel
b
C
c
a
a
b
Step 20.
Screw into any side units using the provided 2x 30mm screws (K) to secure the
unit. Screw just to the rear of the hinge plate then place a cover cap (M) on the
head to conceal it.
Screws for attaching to walls are not provided as these vary depending on materials,
thickness and construction. Ensure appropriate xings for wall construction are used.

Page 7
WALL UNIT
1000 Tall 2 Door Assembly Guide
Step 20.
Insert hinge in top & bottom holes as shown below.
Step 21.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 22.
Attach the door to unit
where required. To attach
door, clip hinge onto hinge
plate and click to secure.
Hinge Cover Caps
Step 24.
Fit cover caps to hinge.
Adjust Soft close to suit.
Step 23.
Adjust hinge to suit. As shown below.
To adjust hinge using
a screw driver, tighten
or loosen as required at
points 1& 2.
Point 1- In - Out
Point 2- Left - Right
12
FRONTAL
HINGE
ADJUSTMENT
Hinge Plates
View from inside of unit
To release door,
pull catch as shown,
to release hinge from
the hinge plate.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
To Move the
hinge up/down,
loosen screws
A + B,
Manoeuvre
the door, then
re-tighten the
screws
A
B