Wren Kitchens TOWER UNIT 600 2 Door Fridge/Freezer Series User manual

2070 x 600
50/50
2070 x 600
70/30
2250 x 600 Tall
50/50
2250 x 600 Tall
70/30
For Internal Use: FI.WR.INS.041 | WKIN00141_TOWER_600_2DrFridgeFreezer_Rev2.psd
TOWER UNIT
600 2 Door
Fridge/Freezer
Assembly Guide

(F) x16
Wooden Dowel
(L) x24
15mm
Screw
(G) x12
Cam Dowel
(Expanding)
(H) x12
Cam lock
(M) x4
Cover Cap
(K) x10
30mm
Screw
(N) x2
Door Buer
(N) x24
Shelf Peg
Plastic
LGE L BRACKET
x2
HINGE MOUNTING PLATE
x4 Inc Screws
HINGE
x4 Inc Screws
(M) x2
Fixing Plate
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
Panel B
x2 End Panel
Panel C
x2 Base Panel
Panel E
x2 Rail Appliance Shelf
x1
Legs
x5
Frontal (packed separately)
x2
SML L BRACKET
(W) x4
70/30 OPTION
50/50 OPTION
For Internal Use: FI.WR.INS.041 | WKIN00141_TOWER_600_2DrFridgeFreezer_Rev2.psd
Page 1
TOWER UNIT
600 2 Door
Fridge/Freezer
Assembly Guide

Step 1.
Dowel (F)
Seat dowel (F) into holes in
both end panels (B) as shown.
Step 2.
Cam dowel (G)
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
DOWEL (F)
& CAM DOWEL (G)
LOCATION DETAIL
Step 3.
Carcass construction
Attach panels (C) and (E) to panels (B),
using cam dowel (G) and also using Dowels (F) (in orange)
in positions as shown.
NB. All CAM LOCK (H) are to be positioned facing
the outside of the unit carcass, for ease of tightening.
Step 4.
Cam lock (H)
Join panels (C) & (E) to (B).
Insert cam lock (H). Do NOT
tighten until Step 6.
Seat (G)
cam dowel
into hole
as shown
Do not use power tools with
cam dowel (G) or cam lock (H)
B
E
E
C
B
C
G F F G
G F F G
B
GFFG
GFFG
B
G
F
F
G
F
F
G
F
F
G
F
F
View from underside
B
G
G
C
View from underside
C
H
H
For Internal Use: FI.WR.INS.041 | WKIN00141_TOWER_600_2DrFridgeFreezer_Rev2.psd
Page 2
TOWER UNIT
600 2 Door
Fridge/Freezer
Assembly Guide

FRONT
Step 5.
Secure each of the legs into
place with 2 x 15mm Screws (L).
Ensure legs are
rotated as shown
so that part of it is
supporting the end
panels (B).
Front legs should
have the at edge
to the front.
LEG POSITON
DIAGRAM
Step 7.
Push leg rmly down into leg base.
Adjust legs to 155mm before
turning carcass upright.
Once in situ level accordingly.
L
FRONT
FRONT
Step6.
Lightly hit centre peg of leg
base with hammer until ush.
C
B
C
B
LC
B
C
B
For Internal Use: FI.WR.INS.041 | WKIN00141_TOWER_600_2DrFridgeFreezer_Rev2.psd
Page 3
TOWER UNIT
600 2 Door
Fridge/Freezer
Assembly Guide

Hinge mounting plate
Attach hinge plates onto end panels (B) In
locations shown using 8 x 15mm screws (L)
hinge side to be mounted in accordance to
customer kitchen plan.
N.B. L Bracket
For appliance shelf, secure to panel (B)
using 4 x brackets (W) locate according to
customer appliance requirements.
70/30
HINGE
POSITION
50/50
HINGE
POSITION
Example
locations
ONLY
70/30 50/50
Example
locations
ONLY
B B
L
L
L
L
L
L
L
L
W W W W
For Internal Use: FI.WR.INS.041 | WKIN00141_TOWER_600_2DrFridgeFreezer_Rev2.psd
Page 4
TOWER UNIT
600 2 Door
Fridge/Freezer
2070
Assembly Guide

Hinge mounting plate
Attach hinge plates onto end panels (B) In
locations shown using 8 x 15mm screws (L)
Hinge side to be mounted in accordance to
customer kitchen plan.
N.B. L Bracket
For appliance shelf, secure to panel (B)
using 4 x brackets (W) locate according to
customer appliance requirements.
70/30
HINGE
POSITION
50/50
HINGE
POSITION
Example
locations
ONLY
70/30 50/50
Example
locations
ONLY
B B
L
L
L
L
L
L
L
L
W W
For Internal Use: FI.WR.INS.041 | WKIN00141_TOWER_600_2DrFridgeFreezer_Rev2.psd
Page 5
TOWER UNIT
600 2 Door
Fridge/Freezer
2250
Assembly Guide

L
L
E
E
Secure tower to the wall using the
L brackets use 2 x 15mm screws (L)
to secure each of the L brackets to the
cabinets at either side. Then screw
through into the wall as shown.
Screws for xing to walls are not
provided as these vary depending on
your wall material and construction.
Ensure appropriate xings for wall
constructions are used.
Secure tower to the wall using
screws through rail panel (E) into the
Wall as shown.
Screws for xing to walls are not
provided as these vary depending
on your wall material and
construction. Ensure appropriate
xings for wall constructions are
used.
For Internal Use: FI.WR.INS.041 | WKIN00141_TOWER_600_2DrFridgeFreezer_Rev2.psd
Page 6
TOWER UNIT
600 2 Door
Fridge/Freezer
Assembly Guide

FOR TOWER FRONTALS
SEE CUSTOMER SPECIFIC
KITCHEN PLAN
Step 8
Insert hinge in top & bottom frontal
holes as shown.
Step 9
Secure hinges by tightening 2 x screws
with plastic grommet attached. These are
already positioned within the hinges.
Step 10.
Align doors to join together using 2 xing
plates (M) to the back of both frontals ensure a
3mm gap is maintained between each frontal
once xed together. Screw in place using
4 x 15mm screws (L) per xing plate (M).
To adjust hinge using a
screwdriver, tighten or
loosen as required at
points 1 & 2.
Point 1- Left - Right
Point 2- Side - Side
To release door,
pull catch as shown,
to release hinge
from the hinge plate.
Step 11.
Attach the door to unit
where required. Adjust
hinges to suit. See below.
To attach door clip hinge
onto hinge plate and click
to secure.
Fit cover caps
to hinge
L
L
L
L
M
L
L
L
L
M
For Internal Use: FI.WR.INS.041 | WKIN00141_TOWER_600_2DrFridgeFreezer_Rev2.psd
Page 7
TOWER UNIT
600 2 Door
Fridge/Freezer
Assembly Guide