Wren Kitchens 150 Pull Out User manual

BASE UNIT
150 - 300 Pull Out
Assembly Guide
For Internal Use: FI.WR.INS.029_WKIN00101_BASE_PullOut_150-300_1Dr_Rev4.indd
150 Pull Out
300 Pull Out

BASE UNIT
150 - 300 Pull Out
Assembly Guide
For Internal Use: FI.WR.INS.029_WKIN00101_BASE_PullOut_150-300_1Dr_Rev4.indd
Page 1
(F) x8
Wooden Dowel
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x6
30mm
Screw
(L) x20
15mm
Screw
(N) x1
Door
Buer
(J) x6
16mm
Runner
Screw
(X) x8
19mm
Screw
(M) x4
Cover
Cap
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Panel A
x1Back Panel
Panel C
x2 Base Fixed Panel
Legs
x4
Frontal
(Packed separately)
x1
Panel B
x2 End Panel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
L Bracket
x2

BASE UNIT
150 - 300 Pull Out
Assembly Guide
For Internal Use: FI.WR.INS.029_WKIN00101_BASE_PullOut_150-300_1Dr_Rev4.indd
Page 2
Step 1.
Seat dowel (F) into
holes in both end
panels (B) as shown.
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Step 3.
Attach panels (C) to panels (B), using
cam dowel (G) & cam lock (H)
(in blue), and also using dowels (F)
(in orange) in positions as shown.
Step 4.
Join panels (C) to (B).
Insert cam lock (H).
Do NOT tighten until Step 6.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening. Do NOT use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
G
G
G
G
G
G
G
G
F
F
F
F
F
F
F
F
B
B B
B
C
C
Seat (G)
cam dowel
into hole as
shown.
B
B
View from underside View from underside
H
G
G
H

BASE UNIT
150 - 300 Pull Out
Assembly Guide
For Internal Use: FI.WR.INS.029_WKIN00101_BASE_PullOut_150-300_1Dr_Rev4.indd
Page 3
Step 5.
Slide back panel (A) into
groove of end panels (B).
Once back panel (A) is in position, ensure
the panel is ush & square with bottom
of end panels (B).
Step 6.
Ensure carcass is square.
Hand tighten all cam locks (H), this will
expand cam dowels (G) and tighten the
unit together.
Step 7.
Secure back panel (A) with 2 x 30mm
screws (K) equally spaced at the top &
bottom of back panel (A) into both xed
panels (C), as shown.
Ensure you screw into the centres of the
base panels (C) (9mm from the edge).
B
C
A
B
A
C
K
K
B
9mm
9mm

BASE UNIT
150 - 300 Pull Out
Assembly Guide
For Internal Use: FI.WR.INS.029_WKIN00101_BASE_PullOut_150-300_1Dr_Rev4.indd
Page 4
C
B
Step 8.
Secure each of the legs into
place with 2 x 15mm screws
(L) per leg.
Step 9.
Lightly hit centre peg of leg
base with hammer until ush.
Step 10.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning carcass
upright. Once in situ level accordingly.
Ensure legs are rotated as shown so that part
of it is supporting the end panels (B).
Front legs should have at edge to the front.
C
B
B
B
B
Front
Front
Front
C
L L
B
Leg Position Diagram
C

BASE UNIT
150 - 300 Pull Out
Assembly Guide
For Internal Use: FI.WR.INS.029_WKIN00101_BASE_PullOut_150-300_1Dr_Rev4.indd
Page 5
Pull Out Pack
Please refer to separate installation instructions
included with your pull out.
For Step 1 in pull out instructions.
Use 16mm screws.
For Step 2 in pull out instructions.
Use 15mm screws.
For Step 4 in pull out instructions.
Use 19mm screws.
Step 1 of pull out
instructions
Step 2 of pull out
instructions
Step 4 of pull out
instructions
Step 4 of pull out
instructions
150 Pull Out
300 Pull Out

BASE UNIT
150 - 300 Pull Out
Assembly Guide
For Internal Use: FI.WR.INS.029_WKIN00101_BASE_PullOut_150-300_1Dr_Rev4.indd
Page 6
For Step 2 in pull out instructions.
Use 15mm screws.
Worktop
Screw up through panel (C) into
your worktop to secure it in place.
Screws for attaching to worktop are not supplied
as these vary depending on worktop material
and thickness. Ensure appropriate xings for
attaching worktop are used. Please refer to the
specialist worktop supplier if these are required
for solid surface worktops.
Screw to Adjacent Unit
Screw through side panels (B) where
appropriate, into any side units, using
the 30mm screws (K) provided to
secure to unit. Place a cover cap (M)
on the head to conceal it.
L Brackets
Where applicable, secure unit to the wall
using 2 x 15mm screws (L) to secure each of the L brackets
to the cabinets at either side. Then screw through into the
wall as shown.
Screws for attaching to walls are not provided as these
vary depending on your wall material and construction.
Ensure appropriate xings for wall construction are
used. L brackets should only be tted for securing wood
and laminate worktops, please refer to the specialist
worktop supplier if these are required for solid surface
worktops.
L
L
C
B
K