Wren Kitchens Vogue TOWER UNIT 300 2 Door 6 Shelf User manual

TOWER UNIT
300 - 600 2 Door 6 Shelf Assembly Guide
For Internal Use: FI.WR.INS.040.WKIN00140_Tower_300-600_2Dr6Shelf.Rev9
300
300
TALL 500 TALL 600
TALL
600
500

Page 1
TOWER UNIT
300 - 600 2 Door 6 Shelf Assembly Guide
L Bracket LGE
x2
Hinge Mounting Plate
x5 Inc Screws
Hinge
x5 Inc Screws
(F) x16
Wooden
Dowel
(L) x24
15mm
Screw
(G) x12
Cam Dowel
(Expanding)
(H) x12
Cam lock
(M) x4
Cover Cap
(K) x10
30mm
Screw
(N) x2
Door Buer
(Z) x24
Shelf Peg
Plastic
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
Panel A
x1 Back Panel
Panel B
x2 End Panel
Panel C
x2 Base Panel
Panel E
x2 Rail
Shelf
x6
Legs
x5 Frontal
x2
(Packed separately)
600 tower shown for
illustration purpose.
(U) x2
Fixing Plate
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.040.WKIN00140_Tower_300-600_2Dr6Shelf.Rev9
B
B
C
C
View from underside View from underside
H
G
G
H
Step 1.
Seat dowel (F) into holes in
both end panels (B) as shown.
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
DOWEL (F)
& CAM DOWEL (G)
LOCATION DETAIL
Step 3.
Attach panels (C) & (E) to panels (B),
using cam dowel (G) (in blue), and also using
dowels (F) (in orange) in positions as shown.
NB. All Cam Lock (H) are to be positioned facing
the outside of the unit carcase, for ease of tightening.
Step 4.
Insert cam lock (H).
Do NOT tighten until Step 6.
Seat (G) Cam
Dowel into hole
as shown
Do not use power tools with
cam dowel (G) or cam lock (H)
B
E
E
C
B
C
GFF G
G F F G
B
GFFG
GFFG
BG
F
F
G
F
F
G
F
F
G
F
F

Page 3
TOWER UNIT
300 - 600 2 Door 6 Shelf Assembly Guide
Step 5.
Slide back panel (A) into groove of end panels (B).
Once back panel (A) is in position, ensure the panel
is ush & square with bottom of end panels (B).
Step 6.
Hand tighten all cam locks (H),
this will expand cam dowels (G)
and tighten the unit together.
9mm
9mm
B
B
E
E
KA
A
C
C
K
Step 7.
Ensure unit is square. Secure back panel
(A) with 6 x 30mm screws (K) equally
spaced at the top & bottom of back
panels (A) into base panels (C),
as shown.
Ensure you screw into the centre of base
panel (C) (9mm from the top or bottom
edge where applicable).

Page 4
For Internal Use: FI.WR.INS.040.WKIN00140_Tower_300-600_2Dr6Shelf.Rev9
B
B
Front
Front
C
Leg position diagram
Step 8.
Position legs as shown.
Ensure legs are rotated to also provide
support to the end panels (B).
Step 9.
Secure each of the legs into place with
4 x 15mm screws (L) per leg.
B
LL
L
L
C
B
C
Step 10.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning unit upright.
Once in situ level accordingly.
It is important to lift unit
onto its legs. Do not tilt as
depicted in image.

Page 5
TOWER UNIT
300 - 600 2 Door 6 Shelf Assembly Guide
Step 11.
Attach hinge plates onto end panels
(B) to suit as shown using 2 screws
already in hinge plates.
Hinge side or sides to be mounted
in accordance to Customer Specic
Kitchen Plan.
Secure tower to the wall using L brackets LGE. Use 2 x 15mm screws (L)
to secure each of the L brackets LGE to the unit at either side. Then screw
through into the wall as shown.
Screws for xing to walls are not provided as these vary depending
on your wall material and construction. Ensure appropriate xings
for wall constructions are used.
Secure tower to the wall using screws through rail
panel (E) into the wall as shown.
Screws for xing to walls are not provided as
these vary depending on your wall material and
construction. Ensure appropriate xings for
wall constructions are used.
See Customer Specic Kitchen Plan
For Tower Frontals
Screw into any side units using the
30mm screws (K) provided to secure
to unit.
Screw just to the rear of the hinge
mounting plates, at the top and
bottom of both sides of the unit,
place cover caps (M) on the heads to
conceal it.
E
E
2006mm
846mm
1426mm
626mm
126mm
1974mm
814mm
1394mm
594mm
94mm
TALL 2250
L
L
K
1826mm
1336mm
846mm
626mm
126mm
1794mm
1304mm
814mm
594mm
94mm
From Bottom From Bottom
2070
B B
FrontFront
INSIDE
FACE
INSIDE
FACE

Page 6
For Internal Use: FI.WR.INS.040.WKIN00140_Tower_300-600_2Dr6Shelf.Rev9
Hinge cover caps
UU
See Customer Specic Kitchen Plan
For Tower Frontals
Fixing plates
Step 14.
Align doors to join together using 2 x xing plates (U) to the back
of both frontals ensure a 4mm gap is maintained between each
frontal once xed together.
Screw in place using 4 x 15mm screws (L) per xing plate.
Step 12.
Insert hinge where required
in holes as shown.
Step 13
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 16.
Fit cover caps to hinge.
Adjust Soft close to suit.
Step 15.
Adjust hinge to suit. As shown below.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
View from Inside of unit
To adjust hinge using a
screw driver, tighten or
loosen as
required at points 1& 2.
Point 1- In - Out
Point 2- Left - Right
12
FRONTAL HINGE
ADJUSTMENT
To Release door
Pull catch as shown,
to release hinge
from the hinge
plate.
To Move the
hinge up/down,
loosen screws
A + B,
Manoeuvre
the door, then
re-tighten the
screws
A
B