Xiaomi Mi Electric Scooter M365 User manual

Xiaomi M365 Edition
Owner’s Manual

INTRODUCTION
Thank you for purchasing our bSeen product.
bSeen is an indicator light kit developed for electric scooters, electric
bicycles and any other vehicle that lacks of indicators, and light warning
systems.
Sold as a “do it yourself” kit, bSeen is a powerful and reliable system,
based on the latest technologies.
At the heart of the system, a micro-controller was programmed for the
most basic tasks, such as right and left turn, and other functions such as
hazard warning lights, horn and headlight control.
bSeen LED units are extremely bright, and can be seen during the day.
LED units are manufactured in-house and carefully inspected to ensure
their waterproof properties.
bSeen handlebar switch unit is easy to operate, with all controls you need
to control the indicator system.!

BOX CONTENTS
Inside your bSeen kit box you will find:
1 x ECU (Electronic Control Unit)
1 x Handlebar Control Unit
4 x LED units with cable tail
ECU (Electronic Control Unit)
Handlebar Control Unit
Amber LED Units
White LED Units

SYSTEM SPECIFICATIONS
ECU
LED units
Handlebar Control
System Functions!
• Input voltage: 18V - 78V DC
• Main board operating voltage: 9V DC
• Outputs voltage: 12V DC regulated
• Power consumption in standby mode: 14mA
• Heat resistant PVC box
• Dimensions: 50mm (L) x 40mm (W) x 33mm (H)
• Weight: 100g
• Maximum operating voltage: 12.7V
• Maximum output power: 2.1W
• Electronic circuit type: Chip on board
• Colour: Cool White (front units), Amber (rear
units)
• IP66 rated waterproof
• Dimensions: 55mm (L) x 15mm (W) x 3.5mm
(H)
• Headlight switch (ON/OFF), Left/Right turn
switch, horn switch.
• LED monitoring for headlight and turning
signals
• Headlight ON/OFF (headlight sold separately)
• Horn ON/OFF time limited to 1.5sec
consecutive buzz (horn sold separately)
• Left Turn
• Right Turn
• Hazard Lights

BASIC INSTALLATION DIAGRAM
Handlebar Control Unit
Front Right LED Unit
Front Left LED Unit
Rear Left LED Unit
Rear Right LED Unit
ECU

BSEEN ELEMENTS’ LOCATION!
Handlebar Control Unit
mounted on the left side of
the handlebar.
Front LED
indicators
mounted on
the wheel
cover
Rear LED
indicators
mounted on
the wheel
cover
ECU mounted inside
the deck

INSTALLATION
bSeen Xiaomi edition was designed to be installed inside your Xiaomi’s
deck, and it uses Xiaomi’s battery power to operate.
INSTALLATION - HANDLEBAR CONTROL UNIT
With the electric scooter upright, start by removing the handlebar grip by
sliding it, as shown below:
PROCEED WITH CAUTION AND READ CAREFULLY
The installation of the bSeen kit requires basic electric skills, such as
connector block connections and stripping electrical wires.
If you’re not familiar with such proceedings, ask for support from your
electric scooter dealer or from an automotive electrician professional.
Damage to the bSeen ECU, LED units and/or Handlebar Control Unit
due to faulty connections, short circuits or polarity inversions, will not be
covered by warranty.
Step 1
Step 2

Once the handlebar grip is removed, install the bSeen Handlebar Control
Unit in place, and tighten the hexagonal screw located at the back of the
unit.
Cut the handlebar grip to size and re-fit it.
Tighten the hexagonal screw located on the back, to
securely hold the Handlebar Control Unit.
Step 3
Step 4
Step 5

The Handlebar Control Unit is supplied with a 2 metres cable length and a
Higo connector. The cable runs inside your Xiaomi’s stem, along with the
brake line - usually a red cable.
Insert cable inside the stem with the
brake line
With the help of a pair of pliers, grab
the cable at the bottom of the stem
Leave the cable loose until you got the
battery compartment opened.

INSTALLATION - REAR LED UNITS CABLES’ PLACEMENT
Start by securing your Xiaomi on the top of a solid surface or support.
Usually a table top, a work bench or a keyboard stand are the most
common supports used to work on electric scooters.