XMark Fitness XM-7617 User manual

Owner’s Manual
XM-7617
POWER TOWER

Table of Contents
2
3
4
5-10
Important Safety Information
Before You Start
Assembly
Parts List
Exploded View
11
12

NOTE: Hand tighten bolts and nylon nuts until machine is fully
assembled.
SAFETY PRECAUTIONS
SAFETY INFORMATION WARNING!
Prior to assembly, remove components from the box and verify that all the listed parts
were supplied.
Before using this unit or starting any exercise program, consult your physician.
This is especially important for persons over the age of 35 and/or persons with pre-
existing health problems. XMARK Fitness assumes no responsibility for personal
injury or property damage sustained by or through the use of this product.
It is the owner’s responsibility to ensure that all users of this unit have read the
Owner’s Manual and are familiar with safety information and precautions.
•This unit should only be used on a level surface and is intended for indoor use
only. XMARK Fitness recommends an equipment mat be placed under the unit to
protect the floor or carpet and for easier cleaning.
•Wear comfortable, good-quality walking or running shoes and appropriate cloth-
ing. Do not use this unit with bare feet, sandals, socks or stockings!
•Always examine your unit before using to ensure all parts are in working order.
•Do not leave children unsupervised near or on the unit.
•Service to your unit should only be performed by an authorized service represen-
tative, unless authorized and/or instructed by a XMARK Fitness technician. Failure
to follow these instructions will void the warranty.
Important Safety Information
3

MODEL: XM-7617
When calling please have the following product information available:
Model Name :
Date Mfg.:
Serial #
Model Name Decal Location
Before You Start
QUESTIONS?
CALL 1-800-719-4605
Monday-Friday
8:30 a.m.-5:00 p.m.
(Central Standard Time)
4
THANK YOU for making this unit a part of your exercise
program.
XMARK Fitness assures the very best in value,
appearance, durability and biomechanics.
XMARK FITNESS SERIES
This manual will guide you through the assembly process. If at any time you
are having trouble with the assembly or use of this product, then please contact
us at our
XMARK Fitness help line. We have trained service technicians on site to
take care of you, our valued customer.
Visit www.xmarkfitness.com for warranty information

Assembly
5

Assembly
NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
Step 1
Connect Upright Frame (#1) to Base Frame (#8) using:
•one M10*75 Button Head Cap Screw (#22)
•two Φ11*Φ23*2 Flat Washer (#19)
•one M10 Nylon Locknut (#25)
Repeat Step 1 for other side of XM-7617.
6

Assembly
NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
Step 2
Connect Back Pad Support Frame (#5) to both Upright Frames (#1) using:
•four M10*80 Button Head Cap Screw (#23)
•eight Φ11*Φ23*2 Flat Washer (#19)
•four M10 Nylon Locknut (#25)
•two Small Plates (#11)
NOTE: Small Plates (#11) are to be placed on the outside of the machine.
Connect Left and Right Angle Supports (#2, #3) to Base Frame (#8) and Cross Frame (#9) using:
•four M10*80 Button Head Cap Screw (#23)
•eight Φ11*Φ23*2 Flat Washer (#19)
•four M10 Nylon Locknut (#25)
Connect Left and Right Angle Supports (#2, #3) to Upright Frame (#1) using:
•two M10*75 Button Head Cap Screw (#22)
•four Φ11*Φ23*2 Flat Washer (#19)
•two M10 Nylon Locknut (#25)
Connect Right and Left Chin-Up Bars (#6, #7) to Upright Frames (#1) using:
•four M10*75 Button Head Cap Screw (#22)
•eight Φ11*Φ23*2 Flat Washer (#19)
•four M10 Nylon Locknut (#25)
•two Bolt cap (#20)
•two Big Plates (#12)
NOTE: Big Plates (#12) are to be placed on the outside of the machine.
7

Assembly
Step 2
8

Assembly
NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
Step 3
Connect Elbow Pad Support Frame (#4) to Upright Frame (#1) using:
• four M10*100 Button Head Cap Screw (#24)
• four Φ11*Φ23*2 Flat Washer (#19)
• four Big Washer (#21)
• four M10 Nylon Locknut (#25)
9

Assembly
NOTE: Wrench Tighten bolts and Nylon Locknuts.
Step 4
Connect Back Pad (#13) to Back Pad Support Frame (#5) using:
• two M10*72 Button Head Cap Screw (#27)
• two Φ11*Φ23*2 Flat Washer (#19)
Connect Elbow Pads (#10) to Elbow Pad Support Frames (#4) using:
• four M10*72 Button Head Cap Screw (#27)
• four Φ11*Φ23*2 Flat Washer (#19)
10