XMark Fitness XM-7626 User manual

Owner’s Manual
8/09
XM-7626
FUNCTIONAL TRAINER

Table Of Contents
Weight Stack Sticker Placement
2
Important Safety Information
Before You Start
Assembly
Parts List
Exploded View
Warranty Information
3
4
5-12
13
14
15
16

NOTE: Hand tighten bolts and nylon nuts until machine is fully
assembled.
SAFETY PRECAUTIONS
SAFETY INFORMATION WARNING!
Prior to assembly, remove components from the box and verify that all the listed parts
were supplied.
Before using this unit or starting any exercise program, consult your physician.
This is especially important for persons over the age of 35 and/or persons with pre-
existing health problems. XMARK Fitness assumes no responsibility for personal
injury or property damage sustained by or through the use of this product.
It is the owner’s responsibility to ensure that all users of this unit have read the
Owner’s Manual and are familiar with safety information and precautions.
• This unit should only be used on a level surface and is intended for indoor use
only. XMARK Fitness recommends an equipment mat be placed under the unit to
protect the floor or carpet and for easier cleaning.
• Wear comfortable, good-quality walking or running shoes and appropriate cloth-
ing. Do not use this unit with bare feet, sandals, socks or stockings!
• Always examine your unit before using to ensure all parts are in working order.
• Do not leave children unsupervised near or on the unit.
• Service to your unit should only be performed by an authorized service represen-
tative, unless authorized and/or instructed by a XMARK Fitness technician. Failure
to follow these instructions will void the warranty.
Important Safety Information
3

MODEL: XM-7626
This manual will guide you through the assembly process. If at any time you
are having trouble with the assembly or use of this product, then please contact
When calling please have the following product information available:
Model Name :
Date Mfg.:
Serial #
Model Name Decal Location
Before You Start
REGISTRATION CARD
QUESTIONS?
CALL 1-800-719-4605
Monday-Friday
8:30 a.m.-5:00 p.m.
(Central Standard Time)
MAILING ADDRESS
7501 Trammel Drive
Shreveport, LA 71108
4
THANK YOU for making this unit a part of your exercise
program.
XMARK Fitness assures the very best in value,
appearance, durability and biomechanics.
XMARK FITNESS SERIES
XMARK Fitness
To avoid unnecessary delays in warranty parts and to insure that a permanent
record of your purchase is on file with our company, be sure to send in the war-
ranty registration card or register online at www
.xmarkfitness.com within 10 days
of purchase.
us at our
XMARK Fitness help line. We have trained service technicians on site to
take care of you, our valued customer.

Assembly
5

Assembly
NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
Step 1
Connect the Left frame(#1)and the Right frame (#2) with two Rear beam (#4) using:
• four M10*80 Button Head Cap Screw (#55)
• four M10*75 Button Head Cap Screw (#56)
• sixteen Φ11*Φ20*2 Flat washer (#60)
• eight M10 Nylon lock nut (#64)
6

Assembly
NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
Step 2
Attach the Main top beam (#3) to the Left frame (#1) and the Right frame (#2) using:
• four M10*105 Button Head Cap Screw (#52)
• eight Φ11*Φ20*2 Flat washer (#60)
• four M10 Nylon lock nut (#64)
7

Assembly
NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
Step 3
Attach:
• two Guide Rod (#19)
• two Φ62*Φ58*Φ25.2*25 Weight bumper (#37)
• five Weight plate 15LB (#39)
• nine Weight plate 10LB (#40)
• five Weight Plate 5LB (#41)
• one Top plate (#34)
to the Left frame (#1) using:
• two M10*50 Button Head Cap Screw (#57)
• two Φ10 Spring washer (#61)
• two Φ11*Φ20*2 Flat washer (#60)
Attach the Weight Pin (#38) to the Top plate (#34).
Attach the Pulley bracket (#30) to the Top plate(#34).
Repeat this step to complete the right side.
8

Assembly
NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
Step 4
Attach the Left slip frame (#5) to the Left slip tube (#13).
Attach the Left slip tube (#13) and the Front support frame (#69) to the Left frame (#1) using:
• two M10*85 Button Head Cap Screw (#70)
• one M10*95 Button Head Cap Screw (#54)
• six Φ11*Φ20*2 Flat washer (#60)
• three M10 Nylon lock nut (#64)
Repeat this step to complete the right side.
9

Assembly
NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
Step 5
Attach one Pulley Cable (#8) to the Left Frame (#1).
Attach two 4.5" Pulley (#33) to the Left Frame (#1) using:
• two M10*50 Button Head Cap Screw (#57) • four Φ11*Φ20*2 Flat washer (#60)
• two M10 Nylon lock nut (#64)
Attach three Small Pulley (#32) to the the Left frame (#1) using:
• one M10*50 Button Head Cap Screw (#57) • two M10*100 Button Head Cap Screw (#53)
• six Φ11*Φ20*2 Flat washer (#60) • three M10 Nylon lock nut (#64)
• four Φ20*Φ16*Φ10.5*27 Longer pulley spacer (#7)
• two Cable retainer bracket (#16)
Attach one Small Pulley (#32) to the Pulley Bracket (#30) using:
• one M10*50 Button Head Cap Screw (#57) • two Φ11*Φ20*2 Flat washer (#60)
• one M10 Nylon lock nut (#64)
Attach two Small Pulley (#32) to the Double pulley Bracket (#28) using:
• two M10*50 Button Head Cap Screw (#57) • four Φ11*Φ20*2 Flat washer (#60)
• two M10 Nylon lock nut (#64)
Repeat this step to complete the right side.
10