XMark Fitness XM-7603 User manual

Owner’s Manual
XM-7603
8/09
FLAT INCLINE BENCH

Assembly 5-8
Parts List 9
Exploded View 10
Warranty Information 11
Table of Contents
Important Safety Information 3
Before You Start 4
2

NOTE: Hand tighten bolts and nylon nuts until machine is fully
assembled.
SAFETY PRECAUTIONS
SAFETY INFORMATION WARNING!
Prior to assembly, remove components from the box and verify that all the listed parts
were supplied.
Before using this unit or starting any exercise program, consult your physician.
This is especially important for persons over the age of 35 and/or persons with pre-
existing health problems. XMARK Fitness assumes no responsibility for personal
injury or property damage sustained by or through the use of this product.
It is the owner’s responsibility to ensure that all users of this unit have read the
Owner’s Manual and are familiar with safety information and precautions.
• This unit should only be used on a level surface and is intended for indoor use
only. XMARK Fitness recommends an equipment mat be placed under the unit to
protect the floor or carpet and for easier cleaning.
• Wear comfortable, good-quality walking or running shoes and appropriate cloth-
ing. Do not use this unit with bare feet, sandals, socks or stockings!
• Always examine your unit before using to ensure all parts are in working order.
• Do not leave children unsupervised near or on the unit.
• Service to your unit should only be performed by an authorized service represen-
tative, unless authorized and/or instructed by a XMARK Fitness technician. Failure
to follow these instructions will void the warranty.
Important Safety Information
3

MODEL: XM-7603
This manual will guide you through the assembly process. If at any time you
are having trouble with the assembly or use of this product, then please contact
When calling please have the following product information available:
Model Name :
Date Mfg.:
Serial #
Model Name Decal Location
Before You Start
REGISTRATION CARD
QUESTIONS?
CALL 1-800-719-4605
Monday-Friday
8:30 a.m.-5:00 p.m.
(Central Standard Time)
MAILING ADDRESS
7501 Trammel Drive
Shreveport, LA 71108
4
THANK YOU for making this unit a part of your exercise
program.
XMARK Fitness assures the very best in value,
appearance, durability and biomechanics.
XMARK FITNESS SERIES
XMARK Fitness
To avoid unnecessary delays in warranty parts and to insure that a permanent
record of your purchase is on file with our company, be sure to send in the war-
ranty registration card or register online at www
.xmarkfitness.com within 10 days
of purchase.
us at our
XMARK Fitness help line. We have trained service technicians on site to
take care of you, our valued customer.

Assembly
5

Assembly
NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
Step 1
Attach Main Frame (#1) to U-Shaped Base (#3) using:
• two M12*80 Button Head Cap Screw (#28)
• four Φ13*Φ26*2 Flat Washers (#32)
• two M12 Nylon Lock Nuts (#34)
Insert Slide Frame (#7) onto Main Frame (#1).
Attach Main Frame (#1) to Rear Upright (#2) using:
• one M10*90 Button Head Cap Screw (#27)
• two Φ11*Φ20*1.5 Flat Washer (#31)
• one M10 Nylon Lock Nut (#33)
Make sure that transport wheels face away from the unit as pictured.
Attach Pin (#10) and Spring (#12) to Main Frame (#1) using:
• one Φ13*Φ26*2 Flat Washer (#32)
• one M12 Nylon Lock Nut (#34)
6

Assembly
NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
Step 2
Attach Seat Pad (#8) to Seat Support (#4) using:
• two Φ11*Φ20*1.5 Flat Washer (#31)
• two M10*70 Button Head Cap Screw (#26)
Attach Seat Support (#4) to Main Frame (#1) using:
• one M12*125 Button Head Cap Screw (#30)
• two Φ13*Φ26*2 Flat Washer (#32)
• one M12 Nylon Lock Nut (#34)
7

Assembly
NOTE: Wrench Tighten bolts and Nylon Lock Nuts.
Step 3
Attach Back Pad Support (#5) to Main Frame (#1) using:
• one Shaft Bolt (#23)
• two Φ13*Φ26*2 Flat Washer (#32)
• two M12 Nylon Lock Nut (#34)
Attach Support Frame, ADJ. (#6) to Back Pad Support (#5) using:
• one Shaft Bolt (#23)
• two Φ13*Φ26*2 Flat Washer (#32)
• two M12 Nylon Lock Nut (#34)
Attach Support Frame, ADJ. (#6) to Slide Frame (#7) using:
• one M12*90 Button Head Cap Screw (#29)
• two Φ13*Φ26*2 Flat Washer (#32)
• one M12 Nylon Lock Nut (#34)
Attach Back Pad, Upper (#9) & Back Pad, Lower (#36) to Back Pad Support (#5) using:
• eight M10*45 Button Head Cap Screw (#25)
• eight Φ11*Φ20*1.5 Flat Washer (#31)
8

XM-7603 Parts List
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
40
41
43
44
45
46
47
48
P00241
P00242
P00246
P00409
P00043
P00410
P00243
P00044
P00045
P00414
P00573
P00415
P00153
P00416
P00023
P00568
P00144
P00249
P00577
P00248
P00571
P00030
P00411
P00203
P00602
P00610
P00615
P00626
P00628
P00621
P00031
P00035
P00561
P00562
P00154
P00046
P00636
P00136
P00022
P00560
P00183
P00638
P00004
P00564
H00030
M00014
Main Frame
Rear Upright, XM-7603
U-Shaped Base
Seat Support
Back Pad Support
Support Frame, ADJ.
Slide Frame
Seat Pad, XM-7603
Back Pad, Upper XM-7603
Pin
Iron Bushing, 21.8*12.2*8
Spring
Foot Cap, Right 50.8 XM Series
Plastic Sleeve 50.8*44.5
Ball Head XM Series
Rubber Bumper
Plastic Sleeve, 63.5*88.9-50.8*76.2
Plug 50.8*76.2
Plug 25
Plug 40*80
Knob Bolt
Wheel
Shaft Bolt
Pop Pin XM Series
Button Head Cap Screw M10*45
Button Head Cap Screw M10*70
Button Head Cap Screw M10*90
Button Head Cap Screw M12*80
Button Head Cap Screw M12*90
Button Head Cap Screw M12*125
Flat Washer Φ11*Φ20*1.5
Flat Washer Φ13*Φ26*2
Nylon Lock Nut M10
Nylon Lock Nut M12
Foot Cap, Left 50.8 XM Series
Back Pad, Lower XM-7603
Button Head Cap Screw M8*25
Flat Washer Φ9*Φ16*1.6
Wrench 17-19
Hex Key S6
Plug 50.8
Button Head Cap Screw M8*45*25
Spacer
Nylon Lock Nut M8
Bolt Pack, XM-7603
Owner's Manual XM-7603
1
1
1
1
2
1
1
1
1
1
10
1
4
1
1
1
2
2
2
1
1
2
2
1
8
2
1
2
1
1
12
13
1
9
4
1
8
12
1
1
1
2
4
2
1
1
Parts List
Ref # Part # Description Qty
9

Exploded View
10