Yealink VC120 V User manual

Yealink VC120 Video Conferencing System Quick Start Guide
Applies to firmware version 40.21.0.15 or later
V21.15
Yealink Network Technology CO., LTD

Table of Contents
Packaging Contents 01
VC120 Connections 02
Remote Control and Cable Ties Installation 04
Bracket and Camera Installation 05
Main Screen 07
Network Deployment 08
Troubleshooting 11

Power Adapter
(2m)
DVI Cable HDMI Cable 2 Ethernet Cable
Velcro 2
+
1
+
AAA Batteries 2
+
Camera VC120 Codec VCR10 Remote Control
Cable Ties 5
+
Quick Start Guide
Please use the Yealink-customized DVI cable
We recommend that you use the accessories provided or approved by Yealink. The use of unapproved third-party
accessories may result in reduced performance.
CPE80 Expansion
Microphone 2
VC120 video conferencing system can work with the video conferencing phone or video conferencing microphone
array. You can purchase any combination according to your needs.
Camera Mounting Accessories
HDMI to VGA Cable
Video Conferencing
Phone
Ethernet Cable
(7.5m)
Ethernet Cable
(7.5m)
VCM30
Microphone Array Package
Video Conferencing Phone Package
+
3.5mm Audio Cable
Packaging Contents

VC120 Connections
Camera
HDMI to VGA Cable HDMI Cable 2m Ethernet Cable Power Adapter
PC Display 2
DVI Cable
+
7.5m Ethernet Cable
CPE80 CPE80
Video Conferencing Phone
2
The video conferencing phone is used to be the audio input/output device:

3
The VCM30 microphone array is used to be the audio input device:
Please connect to the Display1 port if you only have one display device
The system should be used with Yealink original power adapter (19V/3.42A) only. The use of the third-party power
Camera
HDMI Cable 2m Ethernet Cable Power Adapter
PC Display 2
DVI Cable
+
VCM30
7.5m Ethernet Cable
HDMI to VGA Cable
adaptermay cause the damage to the system

Remote Control and Cable Ties Installation
4
Fasten the cables with the cable tie
Install batteries

Bracket and Camera Installation
Please chose the following installation mode when the thickness of the TV is between 35-120mm
Hanging Mode
Adjust the bracket to ensure close adhesion to the back of the TV
Lock the camera to the L-bracket.
1
Steps:
Make sure the back of the TV is clean, and then adjust the bracket to ensure close adhesion to the back of the TV
33
2
5
TV
4
3
1
2
Remove the protection of the Velcro. Put the L-bracket on the top of the TV.
with Velcro.
4

The recommended height for camera positioning is 1.5m-1.8m above the ground
Wall Mount Method
Hole diameter: 6mm
Hole depth: 30mm
50mm
100mm 4
1
3
2Screw specification: M3 8
+
Screw specification: T4 30
+
Steps：Punch holes & Insert expansion bolts Drive screws Adjust the screws position and manually lock them
13
6
2
5
6
5 6
Insert screws to lock the bracket to the wall Connect DVI cable Lock the camera
4

Main Screen
7
Time and date Site name Status icon System IP address and
account information
6

Network Deployment
To ensure that the VC120 works correctly, please configure it according to the conference role that it plays. If it is in the
head office, please make sure that it can be reached from the public network. If it is in a branch office, please use an
intelligent firewall to deploy it, or just follow the same steps as for the head office.
Head Office
At least one static public IP address is required in the head office to allow branch offices to connect. The recommended
system configurations are as follows :
. To deploy the VC120 on a public network, you need to assign a static public IP address to the VC120.
. To deploy the VC120 in an Intranet, you must assign a static private IP address behind the firewall to the VC120. In
the meantime, do port mapping on the firewall for VC120.
Configure a Static IP
8
Firstly, configure a static IP for the VC120
For example: use the remote control to configure a static IPv4 address to your VC120.
.
Menu->Advanced (Admin Password:0000)->LAN Configuration
Select【IPv4】from the【IP Mode】pull-down list
Select【IPv4】
.
.

Configure Port Mapping
If the VC120 is deployed in an Intranet, you need to finish the following port mapping on the firewall:
9
. Press 【Save】to save the configuration, then the screen prompts【Reboot now】
. Press【OK】
to reboot the system.
Enter the IP address, subnet mask, gateway and DNS information in corresponding fields.
Turn off the【DHCP】
.
.
PortFunction
H.323 signal port
SIP（optional ）
Audio & Video media stream port
Web management port（optional ）
Protocol Type
UDP/TCP
5060
443
50000-50499
1719-1720
TCP/UDP
TCP/UDP
TCP

Branch Office
If you are in a branch office, following two options are suggested:
Option1: Deploy the VC120 following the same steps as for the head office. In this way, both inbound and outbound
calls are available.
Option2: Deploy the VC120 using an intelligent firewall, which means that plug and play is possible without any further
firewall configuration, but only outbound calls are available.
Please note that when the VC120 is deployed with an intelligent firewall, you have to open ports (as shown below)
It is recommended that you forward the web management port(443/TCP) to the public network, so that the head office
10
PortFunction
H.323 signal port
SIP（optional ）
Audio & Video media stream port
Protocol Type
UDP/TCP
TCP/UDP
TCP/UDP
50000-50499
5060
1719-1720
permission if they are restricted
can remotely manage the branch office.

Bandwidth Requirements
To ensure the best video conference performance , the recommended bandwidth for VC120 is as below:
For more information on configurations, contact your system administrator.
The bandwidth mentioned above is based on a two-way conference. Head office bandwidth should be increased in line
with the growing number of connected branch offices.
Troubleshooting
After installation and deployment, you can test the VC120 by dialing the Yealink Demo Room. If you can’t dial out
successfully, please contact your IT administrator to check the internal network configuration.
Assume that you are A in head office. Using the configuration method explained in "Head Office" chapter on page 8,
you find that you can call B in branch office or Yealink Demo, but that they cannot call you. The most likely reason is
that the firewall or gateway in the environment does not support the H.323 ALG feature. In this situation, please take
the following actions so that the
11
Video Resolution Recommended Bandwidth
Full HD 1080P 1.3Mb
People 1080P+Content 1080P 2.6Mb

NAT feature on the VC120 can solve this problem. (Carry out each step via the remote control)
. Menu->Advanced(Admin Password:0000)->NAT/Firewall
. Select 【Auto】from the 【Type】pull-down list, the system will obtain public IP address automatically.
. If the system does not obtain a public IP address automatically, select【Manual Settings】from the 【Type】
pull-down list, and then enter the public IP address in the 【Public IP Address】field.
Yealink Test Room IP: 117.28.251.50、117.28.251.51
12

YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD.
Web: www.yealink.com | Addr: 309, 3th Floor, No.16, Yun Ding North Road, Huli District, Xiamen City, Fujian, P.R. China | Copyright ©2016Yealink Inc.All right reserved.