Zamel ledix SLR-11 User manual

www.ledix.pl
Wireless
RGB controller
SLR-11
Cet Lighting Sp. z o.o.
PL 43-200 Pszczyna, ul. Zielona 27, Poland
tel: [phone], fax: [phone]
e-mail: [email protected], www.ledix.pl
10÷14 V DC / 0,22 W; IP20
weight: 27 g
Declaration of Conformity is on www.ledix.pl
Wireless RGB controller
SLR-11
The symbol means selective
collecting of electrical and electronic
equipment. It is forbidden to put
the used equipment together with
other waste.
SLR-11 controller is designed to control LED RGB diodes in the circuit with common “+”
potential (RGB LEDIX series standard ttings, RGB strips and modules) supplied with
10 ÷ 14 V DC. The control is carried out wireless in cooperation with selected EXTA FREE
system transmitters or with dedicated P-260 remote control.
Characteristic features:
• 5programmes:colourselection(toselect1of10coloursdefinedbytheproducer),bright-
ening/dimming, fluent automatic colour change mode (FLOATING), step by step auto-
matic colour change (STROBE) – only for the P-260 remote control, fluent colour selection
(RAINBOW) – only for P-260 remote control,
• wireless control system (EXTA FREE transmitters and dedicated P260 remote control-
remote control),
• 3 transistor outputs (MOSFET) with a maximum current capacity of 4 A per each output,
• 9-bits control system guarantees fluent colour change in FLOATING mode,
• wide operation range (up to 230 m in the open area),
• low power consumption in the standby mode – controller is designed for continuous op-
eration.
Mounting in a Ø60
junction box
Mounting
indoor only
Co-operation
with EXTA FREE
transmitters
SLR-11 ENG Ver. 01
SCAN
the technical
data
10 ÷ 14 V DC
Wireless RGB controller
TYPE: SLR-11
A detailed mounting instruction is in the packaging
CET Lighting Sp. z o.o. declares that
the equipment complies with the principal
requirements and other applicable rules
of the RTTE Directive.

230 V AC 14 V DC
CAUTION !The device is designed for single-phase installation and must be installed
in accordance with standards valid in a particular country. Installation, connection
and control should be carried out by a qualied electrician sta, who act in accord-
ance with the service manual and the device functions.
1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch- discon-
nector combined to the proper circuit.
2. Check if there is no voltage on connection cables by means of a special measure equip-
ment.
3. Connect the power supply to 230 V AC.
4. Connect the cables to the appropriate control terminals in accordance with the con-
nection diagram.
5. Mount the controller in the Ø60 junction box.
6. Switch on the power supply from the mains.
7. Add selected transmitters to the controller (a description is in TRANSMITTERS’ PRO-
GRAMMING section) and check their proper functioning.
SLR-11 controller is designed for cooperation with LED standard lamps with RGB LEDIX
series diodes and with other RGB products supplied with 10÷14 V DC (tapes, strips, mod-
ules and LED RGB lamps) in the circuit with common “+” potential. The control is carried
out wireless in cooperation with selected EXTA FREE system transmitters or with a dedi-
cated P-260 remote control. Depending on the transmitter the controller controls the func-
tions: switching on/ switching o, uent change of the illumination power, selection 1 of
10 colours with factory conguration, uent colour selection and the programs for uent
automatic colour change (FLOATING) and step by step automatic colour change (STROBE).
The controller features:
•wirelesscontrolsystemforLEDRGBstandardttingsoftheLEDIXsystem,
•to carry out the functions as follows: switching on/ switching o, uent change of the lumi-
nous ux intensity, selection 1 of 10 colours with a default setting, uent colour selection,
•programme realisation: automatic colour change (FLOATING) and step by step colour
change (STROBE),
•time for FLOATING and STROBE programmes is adjusted during 10 steps,
•cooperation with transmitters of the EXTA FREE wireless control system and with a dedi-
cated P260 remote control,
•9-bit fast PWM outputs allow the brighting/dimming function to be very uent,
•low power consumption in the standby mode (0.25 W) – controller is designed for continu-
ous operation.
TECHNICAL DATA
MOUNTING
DESCRIPTION DIAGRAM
APPEARANCE
Nominal supply voltage: 10 ÷ 14 V DC
Nominal power consumption: 0,22 W
Number of channels: 3
Maximum current in the channel: 2,5 A
Controlling signal: PWM 9-bit
Functions:
Switch on/ switch o
Selection 1 of 10 colours with factory conguration
Change of the luminous ux intensity
Fluent colour selection – only for the P-260 remote control
Programs in operation:
Fluent automatic colour change (FLOATING)
Step by step automatic colour change (STROBE) – only
for the P-260 remote control
Steps (FLOATING and STROBE) 10 (to 50 min.)
Control: Selected EXTA FREE* system or P-260 transmitters
Radio transmission: 868,32 MHz
Transmission method: One-way without conrmation
Coding: Yes – transmission with addressing
Maximum number of transmitters: 32
Range: Up to 230 m in the open area
Ambient temperature range: -10 ÷ +55
o
C
Casing protection degree: IP20
Protection class: III
Dimensions: 47,5 x 47,5 x 20 mm
Weight: 27 g
Reference standard: PN-EN 60669; PN-EN 61000
CAUTION! Nominal output voltage of the power supply (10÷14 V DC) and its nominal out-
put power must be adjusted for LED light source connected to the controller.
Output terminals (RGB+)
for connection with RGB products
Power supply terminals (+, -)
Optic signaling of the
controller’s operation
Programming button
MAXIMUM CURRENT CAPACITY:
Up to 25 W per channel for LED RGB products supplied with 10 V
Up to 30 W per channel for LED RGB products supplied with 12 V
Up to 35 W per channel for LED RGB products supplied with 14 V
Example of the RGB
LEDIX series tting
blue
R
greenG
red
B
+
*the SLR-11 controller does not cooperate with one push-button transmitters e.g. RNL-01

The application shows the method to use the LEDIX series ttings with RGB radio controller
and RGB SLR-11 wireless controller. The ttings cooperate with the P-256/8 remote control.
From the remote control level it is possible to switch on/switch o 1 of 8 colours added
to 1÷8 keys or it can be possible to activate the uent mode (FLOATING) or step by step
mode (STROBE) for the colour change. Depending on the version the tting can be sup-
plied directly with 230 V AC or with 14 V DC power supply. SLR-11 controller is connected
with RGB tape supplied with 12 V DC. The controller cooperates with a RNK-04 push-button
transmitter. By means of this transmitter the RGB strips can be switched on/switched o or
brightened/dimmed or the FLOATING mode can be released. The controller is designed for
mounting in a typical junction box Ø=60 mm.
APPLICATION
OPERATION TABLE
Symbol
RNK-02 RNK-04
P-256/8 P-257/2 P-257/4
RNM-10
RNP-01 RNP-02
RNL-01
RTN-01
RCR-01
RTI-01
RXM-01
P-260
SLR-11
180 180 230 180 180 230 160 160 - 200 - 160 230 200
CAUTION:The given range concerns open area - an ideal condition without any natural
or articial obstacles. If there are some obstacles between a transmitter and a receiver,
it is advisable to decrease the range according to: bricks: from 10 to 40 %, wood and
plaster: from 5 to 20 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%,
glass: from 10 to 20 %. Over- and underground medium and high electrical power
lines, radio and television transmitters, GSM transmitters set close to a device system
have also a negative inuence on the range.
TRANSMITTERS PROGRAMMING
RADIO TRANSMITTERS DELETION
Wireless EXTA FREE system transmitters
Touch P-260 remote control
An exemplary programming procedure with the use of P-257/2 remote control. The
procedure for the rest of radio EXTA FREE transmitters is analogous.
CAUTION: 32 dierent transmitters can be added to a single SLR-11 controller. In case of
adding more than 32 transmitters, STATUS diode will ash a few times while adding them.
Press and release the rst
transmitter’s push-button.
LED red diode switches on
(rst the signal pulsates,
next the signal
is constant).
Press and release the
second transmitter’s
push-button. LED red
diode switches on (the
signal pulsates) and
next it switches o - THE
TRANSMITTER IS ADDED.
Press PROG push-button of
SLR-11 device for a longer time
until LED red diode switches on
(constant signal). Next release
PROG push-button.
Press PROG push-button
in SLR-11 controller
for a longer time.
After 5 seconds LED red
diode switches on (the
signal pulsates) and then
it switches o.
Release the push-button
in SLR-11 – THE MEMORY
IS DELETED.
Press PROG push-button in
the controller for a longer
time until STATUS red diode
switches on (constant signal).
Next release PROG push-
button.
Press the switch on/switch
o push-button of the
P-260 remote control for
a longer time. STATUS
red diode switches on in
the controller (rst signal
pulsates, next the signal
is constant).
Release switch on/switch
o push-button of the
P-260 remote control.
STATUS red diode switches
on (the signal pulsates),
next it switches o - it
means the TRANSMITTER
IS ADDED.

OPERATION
Cooperation with the transmitters of the EXTA FREE system (example of P-257/2)
•Pressshortpush-button1– switching on/ switching o.
•Presspush-button1for a longer time (>3 s) – brightening/dimming in following sequence:
brighten – stop – dim. The function is available also in the FLOATING mode.
•Pressshortpush-button2– selection 1 out of 10 colours from the default setting (see the
table).
•Presspush-button2for a longer time (>3 s) – entry to the FLOATING mode.
•Pressshortpush-button2in the FLOATING mode – change of the step (1-10) for the FLOAT-
ING mode.
•Eachchangeofthestepissignalizedbyaashingoftheloadconnectedtothecontroller
output. The transition between step 1 and 10 is signalized by repeated ashing of the load.
The step 1 means that the colour change is the fastest (the whole cycle takes about 2 min-
utes), the step 10 means that the colour change is the slowest (the whole cycle takes about
50 minutes).
•Presspush-button2for a longer time (>3 s) in the FLOATING mode – exit of this mode.
•Thecontrollerremembersthelastsettingofthemodeandsettingofthelevelofthelumi-
nous ux intensity after switching o by means of push-button 1.
Cooperation with the P-260 remote control
Switching on a suitable function/programme is carried out by pressing suitable push-but-
tons of the P-260 remote control:
•ON/OFF - switching on/ switching o.
•Brightening/dimming function – pressing this push-button, the function carries out the
uent change of the luminous ux intensity. This function is available in FLOATING and
STROBE modes.
•FLOATING – activation/deactivation of the programme for automatic and uent colour
change.
•STROBE – activation/deactivation of the programme for automatic and step by step colour
change.
•TOUCH AREA – allows the colour selection in a uent way.
If the active mode is the FLOATING or STROBE mode then the following pressing of the push-
buttons described as FLOATING, STROBE carries out the speed change (from 1 to 10 step) in
this mode. Each change of the step is signalized by ashing of the load which is connected
to the controller’s output. The transition between step 10 and 1 is signalized by a repeated
ashing of the load. The step 1 means that the colour change is the fastest (the whole cycle
takes about 120 s), step 10 means that the colour change is the slowest (the whole cycle
takes about 50 minutes).
Colour table dened in the controller
Brightening
ON/OFF
FLOATING mode STROBE mode
Dimming
Touch eld
Fluent colour selection
Button 1 and 2