ABB SACE Tmax T6 User manual

C
Doc. N.° 1SDH001352R0001 - L9714
SACE Tmax T6 1000V DC for Jumpers
B
A
G
HI
ABC D E F
57 150 162.5 155 210 102.5
G H I
625 155 420
Cubicle Dimensions [mm]
UPPER SUPPLY LOWER SUPPLY
120
For 4PS solution consider distances D, E, F symmetricaly with respect to X-X CB axis
2 Nm
B
D
EC
A
METALLIC
FRAME
XX
Y
Y
F
A
B
D
E
C
A
METALLIC
FRAME
XX
Y
Y
F
A
Istruzioni di installazione Tmax T6 1000V DC per Jumpers
Installation instructions Tmax T6 1000V DC for Jumpers
Installationsanleitung Tmax T6 1000V DC für Jumpers
Instructions pour l'installation Tmax T6 1000V DC pour Jumpers
Instrucciones de instalación Tmax T6 1000V DC para Jumpers
Insulation distances for installation
in metallic cubicle [mm]

F
D
Tmax | ABB
G
If the device is equipped
with motor operator, MOE,
openings with current shall
be performed using SOR or
UVR.
E
(mm) CON MOSTRINA
WITH FLANGE
SENZA MOSTRINA
WITHOUT FLANGE
A149 142
B116 107
C66.75 62.25
Per configurazioni di cablaggio diverse da quelle di seguito rappresentate eseguire prove di tipo specifiche
sull'installazione e usare connessioni isolate
For different wiring configurations than those shown afterwards perform specific type test on the installation and use
insulated terminals connection
Für Konfigurationen mit anderer Verdrahtung als unten stehend abgebildet, sind spezifische Stücknachweise auf der
Installation auszuführen und isolierte Anschlüsse zu benutzen.
Pour les configurations de câblage différentes de celle représentées ci-dessous, effectuer des essais spécifiques de
type sur l'installation et utiliser des connexions isolées
Para configuraciones de cableado distintas a las que se representan a continuación efectuar pruebas de tipo
específicas en la instalación y usar conexiones aisladas
对不同于后续所示的布线，需对安装进行指定的型式试验，并使用绝缘的端子连接
CLACK
OFF ON TRIPPED
237
118.5
140
ø5.5 (M5)
C
A
B
= =
XX
Y
Y
35

Tmax | ABB
I
2PS+2PS solution, Lower Supply
LOAD
F
Example for 2P+2PS (Lower Supply)
H
Jumper examples
Example for 4PS (Lower Supply)
2PS+2PS
FCCuAl R
F
9 Nm
9 Nm
T6 OVERALL DIMENSIONS:
268
= =
380
279.5
120
84.5
25.3
154.746.8
70 70 70
105
95
116
161
48
24
X
X
Y
Y
XX
44.7
280
105
225
225
118.5
12
ø6
22.5
40
44
≥ 3 9 Nm
24 5
103
108 ≤ 2

LOAD
* Terminals configurations must be symmetrical with respect to x-x CB axis when CB is supplied from the top
Tmax | ABB
K2PS+2PS solution, Upper Supply
2PS+2PS solution, Lower Supply - Terminals
J
2PS+2PS
FCCuAl R
F
R
X
227.5
X
70 70 70
30.5
Ø14
FCCuAl
70 70 70
X
X
227.5
2
MIN
最小值
(0,7)
MED
中间值
(0,85)
MAX
最大值
(1xIn)
In
TMA
I1
最小值
(In x 5)
MED
中间值
(In x 7,5)
MAX
最大值
(In x 10)
630 3150 4725 6300
800 4000 6000 8000
MIN
In
TMA
I3
1
CLACK
630 441 535,5 630
800 560 680 800
L
52
22.5
47
Ø21.5
In 630A
63.5
44
47.5
Ø19.4
In 800A

www.abb.com
© Copyright 2011 ABB. All rights reserved.
For more information please contact:
ABB S.p.A.
ABB SACE Division
Via Pescaria, 35
24123 Bergamo - Italy