ADF Web HD67810-KNX-B2 User manual

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 1 di 26
User Manual
Revision 1.001
English
J1939 / KNX - Converter
(Order Code: HD67810-KNX-B2)
for Website information:
www.adfweb.com? roduct=HD67810
for rice information:
www.adfweb.com? rice=HD67810-KNX-B2
Benefits and Main Features:
Very easy to configure
Electrical isolation
Temperature range: -40°C/85°C (-40°F/185°F)
For others KNX products, see also the following links:
Converter KNX to
www.adfweb.com? roduct=HD67801 (BACnet Master)
www.adfweb.com? roduct=HD67802 (BACnet Slave)
www.adfweb.com? roduct=HD67803 (CAN)
www.adfweb.com? roduct=HD67804 (CANo en)
www.adfweb.com? roduct=HD67807 (EtherNet/IP)
www.adfweb.com? roduct=HD67808 (DeviceNet Master)
www.adfweb.com? roduct=HD67809 (DeviceNet Slave)
www.adfweb.com? roduct=HD67811 (M-Bus Master/wM-Bus)
www.adfweb.com? roduct=HD67812 (Modbus Master)
www.adfweb.com? roduct=HD67813 (Modbus Slave)
www.adfweb.com? roduct=HD67814 (Modbus TCP Master)
www.adfweb.com? roduct=HD67815 (Modbus TCP Slave)
www.adfweb.com? roduct=HD67818 (PROFINET)
www.adfweb.com? roduct=HD67820 (SNMP)
www.adfweb.com? roduct=HD67821 (DMX)
www.adfweb.com? roduct=HD67822 (DALI)
www.adfweb.com? roduct=HD67825 (Ethernet)
Do you have an your customer protocol?
www.adfweb.com? roduct=HD67003
Do you need to choose a device? do you want help?
www.adfweb.com?Cmd=helpme
User Manual

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 2 di 26
INDEX:
age
INDEX 2
U DATED DOCUMENTATION 2
REVISION LIST 2
WARNING 2
TRADEMARKS 2
SECURITY ALERT 3
EXAM LE OF CONNECTION 4
CONNECTION SCHEME 5
CHARACTERISTICS 6
CONFIGURATION 6
OWER SU LY 7
FUNCTION MODES 8
LEDS 9
CAN 10
KNX 11
ETHERNET 12
USE OF COM OSITOR SW67810 13
NEW ROJECT / O EN ROJECT 14
SOFTWARE O TIONS 15
SET COMMUNICATION 16
KNX ACCESS 17
RECEIVE FRAMES 19
SEND FRAMES 20
U DATE DEVICE 21
MECHANICAL DIMENSIONS 23
ORDERING INFORMATIONS 24
ACCESSORIES 24
DISCLAIMER 25
OTHER REGULATIONS AND STANDARDS 25
WARRANTIES AND TECHNICAL SU ORT 26
RETURN OLICY 26
UPDATED DOCUMENTATION:
Dear customer, we thank you for your attention and we remind you that
you need to check that the following document is:
Updated
Related to the product you own
To obtain the most recently updated document, note the “document code”
that appears at the top right-hand corner of each page of this document.
With this “Document Code” go to web page www.adfweb.com/download/
and search for the corresponding code on the page. Click on the proper
“Document Code” and download the updates.
REVISION LIST:
WARNING:
ADFweb.com reserves the right to change information in this manual about
our product without warning.
ADFweb.com is not responsible for any error this manual may contain.
TRADEMARKS:
All trademarks mentioned in this document belong to their respective
owners.
Revision Date Author Cha ter Descri tion
1.000 15/06/2015 Ff All First Release
1.001 05/06/2017 Ff All Revision

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 3 di 26
SECURITY ALERT:
G ENERAL I NFORMATION
To ensure safe operation, the device must be operated according to the instructions in the manual. When using the device, legal and
safety regulation are required for each individual application. The same applies also when using accessories.
I NTENDED U SE
Machines and systems must be designed so the faulty conditions do not lead to a dangerous situation for the operator (i.e.
independent limit switches, mechanical interlocks, etc.).
Q UALIFIED P ERSONNEL
The device can be used only by qualified personnel, strictly in accordance with the specifications.
Qualified personnel are persons who are familiar with the installation, assembly, commissioning and operation of this equipment and
who have appropriate qualifications for their job.
R ESIDUAL R ISKS
The device is state-of-the-art and is safe. The instruments can represent a potential hazard if they are inappropriately installed and
operated by untrained personnel. These instructions refer to residual risks with the following symbol:
This symbol indicates that non-observance of the safety instructions is a danger for people that could lead to serious injury or
death and / or the possibility of damage.
CE CONFORMITY
The declaration is made by our company. You can send an email to [email protected]om or give us a call if you need it.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 4 di 26
EXAMPLE OF CONNECTION:

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 5 di 26
CONNECTION SCHEME:
Figure 1: Connection scheme for HD67810-KNX-B2

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 6 di 26
CHARACTERISTICS:
The HD67810 is a J1939 / KNX Converter.
It has the following characteristics:
Up to 1440 bytes in reading and 1440 bytes in writing;
Triple isolation between KNX - ower Supply, KNX – CAN, ower Supply - CAN.
Two-directional information between KNX bus and J1939 bus;
Mountable on 35mm Rail DIN;
Wide power supply input range: 8…24V AC or 12…35V DC;
Wide temperature range: -40°C / 85°C [-40°F / +185°F].
CONFIGURATION:
You need Compositor SW67810 software on your C in order to perform the following:
Define the parameter of J1939 line;
Define the parameter of KNX line;
Define the KNX messages that the Converter can accept;
Define the KNX frames that the Converter sends trough the KNX line;
Define the map of KNX byte that must be written in the J1939 side;
Define the map of which J1939 data must be written in KNX messages;
Update the device.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 7 di 26
POWER SUPPLY:
The devices can be powered at 8…24V AC and 12…35V DC. For more details see the two tables below.
VAC
VDC
Vmin Vmax Vmin Vmax
8V 24V 12V 35V
Consumption at 24V DC:
Device Consum tion [W/VA]
HD67810-KNX-B2 3.5
HD67810-KNX-B2
Caution: Not reverse the olarity ower

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 8 di 26
FUNCTION MODES:
The device has got two functions mode depending of the position of the ‘Dip1 of Dip-Switch A’:
The first, with ‘Dip1 of Dip-Switch A’ at “OFF” position, is used for the normal working of the device.
The second, with ‘Dip1 of Dip-Switch A’ at “ON” position, is used for upload the roject and/or Firmware.
For the operations to follow for the updating, see ‘U DATE DEVICE’ section.
According to the functioning mode, the LEDs will have specifics functions, see ‘LEDS’ section.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 9 di 26
LEDS:
The device has got six LEDs that are used to give information of the functioning status.
The various meanings of the LEDs are described in the table below.
LED Normal Mode Boot Mode
1: Device State (green) Blinks slowly (~1Hz) Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
2: J1939 communication
(yellow) Blinks when J1939 frame is received Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
3: KNX communication
(yellow) Blinks when KNX frame is received Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
4: Not used (yellow) OFF Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
5: Ethernet Link (green) ON: Ethernet cable connected
OFF: Ethernet cable disconnected
ON: Ethernet cable connected
OFF: Ethernet cable disconnected
6: KNX rogrammation (red) ON: KNX rogrammation activated
OFF: KNX rogrammation not activated
OFF

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 10 di 26
J1939:
For terminate the J1939 line with a 120Ω resistor it is necessary that the Dip1 of ‘Dip-Switch C’ is at ON position.
Cable characteristics:
DC arameter: Impedance 70 Ohm/m
AC arameters: Impedance 120 Ohm/m
Delay 5 ns/m
Length Baud Rate [b s] Length MAX [m]
10 K 5000
20 K 2500
50 K 1000
100 K 650
125 K 500
250 K 250
500 K 100
800 K 50
1000 K 25

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 11 di 26
KNX:
KNX is the standard that allows the automated and decentralized management of the technologic plans of
a big typology of structures: commercial buildings, factories, houses, public locals, schools and so on.
KNX can be used in all the applications and functions for the building automations: from lighting to control
dampers, to the security, to the heating monitoring, to the conditioning, to the hydric control and alarms,
to energy management and so on.
Characteristics Descri tion TP1-256
Medium Shielded Twisted air
Topology Linear, Star, Tree or mixed
Baudrate 9600 bps
Device supplying Normal: bus powered devices
Optional: remote powered devices
Device power consumption 3 mA- 12 mA
ower Supply Unit ( SU) DC 30 V
Number of SU’s per physical
Segment Max. 2
Number of connectable devices
per physical Segment Max. 256
Number of addressable devices
per physical Segment Max. 255
Total cable length per physical
Segment Max. 1000 m
Distance between two devices Max. 700 m
(*) Taken from KNX specifications

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 12 di 26
ETHERNET (PROGRAMMING PORT):
The Ethernet ports are used for programming the device.
The Ethernet connection must be made using Connector2 of HD67810-KNX-B2 with at least a Category 5E cable. The maximum length of the
cable should not exceed 100m. The cable has to conform to the T568 norms relative to connections in cat.5 up to 100 Mbps. To connect the
device to an Hub/Switch is recommended the use of a straight cable, to connect the device to a C is recommended the use of a cross cable.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 13 di 26
USE OF COMPOSITOR SW67810:
To configure the Converter, use the available software that runs with Windows called SW67810. It is downloadable on the site
www.adfweb.com and its operation is described in this document. (This manual is referenced to the last version of the software present on
our web site). The software works with MSWindows (X , Vista, Seven, 8, 10; 32/64bit).
When launching the SW67810, the window below appears (Fig. 2).
Note:
It is necessary to have installed .Net Framework 4.
Fi
gure 2: Main window for SW67810

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 14 di 26
NEW CONFIGURATION / OPEN CONFIGURATION:
The “New Configuration” button creates the folder which contains the entire device’s configuration.
A device’s configuration can also be imported or exported:
To clone the configurations of a rogrammable “J1939 / KNX - Converter” in order to
configure another device in the same manner, it is necessary to maintain the folder
and all its contents;
To clone a project in order to obtain a different version of the project, it is sufficient to
duplicate the project folder with another name and open the new folder with the
button “O en Configuration”.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 15 di 26
SOFTWARE OPTIONS:
By pressing the “Settings” ( ) button there is the possibility to change the
language of the software and check the updatings for the compositor.
In the section “Language” it is possible to change the language of the
software.
In the section “Connection Options”, it is possible to check if there are some
updatings of the software compositor in ADFweb.com website.
Checking the option “Check Software U date at Start of Program”, the
SW67810 check automatically if there are updatings when it is launched.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 16 di 26
SET COMMUNICATION:
This section define the fundamental communication parameters of two buses, KNX and J1939.
By ressing the “Set Communication” button from the main window for SW67810 (Fig. 2) the
window “Set Communication” appears (Fig. 3).
The window is divided in three sections, one for the KNX, one for the J1939 and the other for Ethernet.
The means of the fields for “KNX” are:
In the field “Ty e” the type of KNX is defined (fixd to ‘KNX T ’);
In the field “ID Device” the ID of the KNX side of the converter is defined.
The means of the fields for the “J1939” section are:
In the field “Baudrate” the baudrate for the J1939 line is defined;
In the field “TimeOut Data (s)” a time is defined. When this time is elapsed, the data on KNX
side are set to 0xFF;
If the field “Enable Peer to Peer” is checked, the converter accepts any ID that have the GN
inserted in the section “Receive Frames”;
In the field “Device ID J1939” the ID for J1939 side of the converter is defined.
The means of the fields for “Ethernet” are:
In the fields “IP ADDRESS” the I address of the converter is defined;
In the fields “SUBNET Mask” the SubNet Mask of the converter is defined;
In the fields “GATEWAY” the default gateway of the net is defined. This feature can be enabled
or disabled pressing the Check Box field. This feature is used for going out of the net.
Figure 3: “Set Communication” window

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 17 di 26
KNX ACCESS:
By pressing the “KNX Access” button
from the main window for SW67810
(Fig. 2) the “KNX Access” window
appears (Fig. 4).
The means of the fields are:
If the field “Enable” is checked,
the KNX message is enabled;
In the field “Source Address”
the Source Address to assign to
the KNX message is defined;
In the field “Dest/Grou the Group address (2 level structure, 3 level structure or free address structure) or the device address is
defined. In case of Group address, the levels must be separated by ‘/’, in case of Device address, the parts of the address must be
separated by ‘.’;
In the field “APCI” the A CI of the KNX message is defined. You can choose between the following:
oRead: it is used to send a reading request to a KNX device;
oWrite: it is used to send a writing request to a KNX device;
oSpecific value (edited manually).
In the field “Priority” the riority of the KNX message is defined. You can choose between the following:
oSystem (Highest);
oUrgent;
oNormal;
oLow (Lowest).
In the field “Format” the data format of the KNX message is defined;
If the field “Extended” is checked, the extended format of the KNX message is used;
If the field “ReTest” is checked, the KNX message is re-sent in case of not correct response;
If the field “OnCMD” is checked, the KNX request is sent when a J1939 frame is received;
If the field “On Change” is checked, the gateway sends the KNX command when the data on J1939 change the value;
If the field “On Timer” is checked, the gateway sends the KNX command cyclically;
Figure 4: “KNX Set Access” window

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 18 di 26
In the field “Poll Time” the delay in ms between two KNX commands is defined (if “On Timer” is checked);
In the field “Position” insert the address of the internal array where placing the information;
In the field “Bit Mode” insert the start bit of the first byte of the field “ osition” where start to insert the data read;
In the field “Length” the dimension of the KNX message is defined;
In the field “Mnemonic” the description for the request is defined.
Note:
If the field “On change” is checked and the “ oll Time” is different from 0, the converter sends the KNX command cyclically and also
when the data is changed.
Note:
If the field “OnCMD”, “OnChange” and “OnTimer” are not checked, the converter only sniffs the bus in order to monitor the status of
the KNX message.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 19 di 26
RECEIVE FRAMES:
By pressing the “Receive Frames” button from the main window for SW67810 (Fig. 2) the “Receive J1939 Frames” window appears (Fig.
5).
The COB inserted in this table contains the Output data of KNX. These frames are accepted by the Converter.
The data of the columns have the following meanings:
In the field “Data Page” the data page is defined, the value can be 0 or 1 (usually it is 0);
In the field “PGN” the GN of the data to read from J1939 net is defined (in the J1939 protocol the GN is an identifier);
In the field “Source Address” the source address of the device that send the frame is defined;
If the field “Trans ort Protocol” is checked, the frame uses Transport rotocol functions;
In the field “Start Byte” the starting byte to save is defined, this field is enabled only when the field Transport rotocol is checked;
In the field “Num Bytes” the number of bytes starting from the “Start Byte” is defined;
If the field “Cancel Data” is checked, when the GN is not received for the “TimeOut Data (s)” defined, the values of KNX side are set
to 0xFF;
If the field “On Request” is checked, the converter send the J1939 request for the GN frame with the “Time (ms)” defined. This
feature is used for GNs that must be required;
In the field “Mnemonic” a description for the frame is defined.
Figure
5
: “Receive
J1939
Frames” window

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
J
1939 / KNX
Document code: MN67810_ENG Revision 1.001 agina 20 di 26
SEND FRAMES:
By pressing the “Send Frames” button from the main window for SW67810 (Fig. 2) the “Send Frames” window appears (Fig. 6).
The COB inserted in this table contains the Input data of KNX. These frames are sent by the Converter.
The data of the columns have the following meanings:
In the field “Priority” the priority of the J1939 message is defined. In J1939 protocol, the priority is a number between 0 and 7. 0 is
the highest priority and 7 is the lowest;
In the field “Data Page” the data page of the J1939 message is defined. The value can be 0 or 1 (usually it is 0);
In the field “PGN” the GN of the J1939 message to be written from KNX is defined (in J1939 protocol the GN is an identifier);
In the field “Source Address” the address of the device that sends the frame is defined;
In the field “Num Byte” the length of the GN is defined;
If the field “Request” is checked, the J1939 frame is sent when a request frame arrives from J1939 network;
If the field “Data Change” is checked, the J1939 frame is sent when a byte from KNX side changes value;
If the field “On Timer” is checked, the J1939 frame is sent cyclically;
In the field “Send Timer” the delay (in milliseconds) with which sending the J1939 message is defined;
In the field “Mnemonic” a description for the frame is defined.
Figure 6
: “
Transmit J1939 Frames
” window