Adtek Cs1-pr User manual

C1-01-1

7-2007-11-07

CS1-PR PROCESSIndicator

DESCRIPTION

CS1-PR economic type Process Indicator has been designed

with high accuracy measurement, display and

communication of DC signal 0~10V and 4(0)~20mA.

They are also available 1 option of 1 Relay outputs, 1

Analogue output or 1 RS485(Modbus RTU Mode) interface

with versatile functions such as control, alarm,

re-transmission or communication for a wide range of

industrial applications.

FEATURE

●Measuring linear signal 0~10V and 0(4)~20mA in one indicator(input code: AV)

●Square Root function available by programming

●Option available 1 of 1 relay, 1 analogue output or RS485(Modbus RTU mode)

●1 relay can be programmed individual to be a Hi / Lo / Hi Latch / Lo Latch energized with Start

Delay / Hysteresis / Energized & De-energized Delay functions.

●Analogue output or RS 485 communication port in option

●CE Approved & RoHS

ORDERING INFORMATION

CS1−PR−Input

Signal −Optional

Output −Excitation

Supply −Aux.

Powered

CODE

INPUT RANGE CODE OPTIONAL O/P CODE EXCIT. SUPPLY CODE AXU. POWER

A1 0(4) ~ 20mA / 0 ~ 10mA NNone NNone AAC115/230V

V1 0 ~ 10V / 0(1) ~ 5V R1 1 Relay E24 DC 24V

AV 0~10V/0(4)~20mA(all in one)

EO Specify ADH* AC/DC 85~264V

AO Specify A input V0(1) ~ 5 V

0 ~ 10 V ADL* AC/DC 20~90V

VO Specify V input

I 0 ~ 10 mA

0(4)~20 mA * ADH* will be available

at Jan. 2008

8 RS 485

Relay, Analogue Output

or RS485 Port can be

selected one only.

Digital fine adjust: Pv.Zro: Settable range: -19999~+29999

TECHNICAL SPECIFICATION Pv.SPn: Settable range: -19999~+29999

Input

Readin

Stable Function

Input Range Input

Impedance Input Range Input

Impedance Average: Settable range: 1~99 times

Voltage 0 ~ 10 V ≥1M ohm Current 4

(

)

~20 m

250 ohm Moving average: Settable range: 1(None)~10 times

¾TheMetercanbe0~10V and 0~20mAinone unit

accordin

connection

#12 Digital filter: Settable range: 0(None)/1~99 times

Calibration: Digital calibration by front key Control Functions(option)

A/D converter: 16 bits resolution Set-points: One set-point

Accuracy: ≤± 0.04% of FS ±1C; Control relay: 1 Relay, FORM-C, 5A/230Vac, 10A/115V

Sampling rate: 15 cycles/sec Relay energized mode: Energized levels compare with set-points:

Response Time: ≤100 msec.(when the AvG = “1”) in standard Hi / Lo / Hi.HLd / Lo.HLd programmable

Input type: 0~10V / 0~5V / 1~5V / 0-10mA / 0~20mA / 4~20mA Energizing functions: Start delay / Energized & De-energized delay / Hysteresis

programmable for coding AV(option) Energized Latch

Start band(Minimumlevel forEnergizing): 0~9999counts

Display & Functions Start delay time: 0:00.0~9(Minutes):59.9(Second)

LED: Numeric: 5 digits, 0.8”(20.0mm)H red high-brightness LED Energized delay time: 0.00.0~9(Minutes):59.9(Second)

Relay output indication: 1 square red LED De-energized delay time: 0.00.0~9(Minutes):59.9(Second)

RS 485 communication: 1 square orange LED Hysteresis: 0~5000 counts

E.C.I. function indication: 1 square green LED

Max/Mini Hold indication: 2 square orange LED Analogue output(option)

Down key function indication(ResetforMax.(Mini.)Hold/ Accuracy: ≤

0.1% of F.S.;

PVHold/Rel.PV):1squaregreenLED Ripple: ≤

0.1% of F.S.

Display range: -19999~29999; Response time: ≤100 msec. (10~90% of input)

Scaling function: Lo.SC: Low Scale; Settable range: -19999~+29999 Isolation: AC 2.0 KV between inputand output

Hi.SC: High Scale; Settable range: -19999~+29999 Output range: Specify either Voltage or Current output in ordering

Decimal point: Programmable from 0 / 0.0 / 0.00 / 0.000 / 0.0000 Voltage: 0~5V / 0~10V / 1~5V programmable

Over range indication: ovFL, when input is over 120% of input range Hi Current: 0~10mA / 0~20mA / 4~20mA programmable

Under range indication: -ovFL, when input is under -20% of input range Lo Output capability: Voltage: 0~10V: ≥1000Ω;

Max / Mini recording: Maximum and Minimum value storage during power on. Current: 4(0)~20mA: ≤600Ωmax

Display functions: PV / Max(Mini) Hold / RS 485 Programmable Functions: Ao.HS(output range high): Settable range: -19999~29999

Front key functions: Relative PV / PV Hold / Reset for maxi(mini) hold / Ao.LS(output range Low): Settable range: -19999~29999

Reset for relay energized latch programmable Digital fine adjust: Ao.Zro: Settable range: -38011~+27524

Low cut: Settable range: -19999~29999 counts Ao.SPn: Settable range: -38011~+27524

Excitation Supply DC24V in build for 2 wire transmitters

CSM-321S

CS2-

CSM-321S CSM-CSM-

CS1-PR

CSM-321S CSM-CSM-

CSM-321SCSM-

CSM-321S

OPTION 4 * It means RoHS

version.

OPTION

WWW.100Y.COM.TW WWW.100Y.COM.TW WWW.100Y.COM.TW

C1-01-2

7-2007-11-07

RS 485 Communication(option)

Protocol: Modbus RTU mode

INSTALLATION

Baud rate: 1200/2400/4800/9600/19200/38400 programmable

Data bits: 8 bits The meter should be installed in a location that dose not exceed the

maximum operating temperature and provides good air circulation.

Parity: Even, odd or none (with 1 or 2 stop bit) programmable

Address: 1 ~ 255 programmable

Remote display: to show the value from RS485 command of master

Distance: 1200M

Terminate resistor: 150Ωat last unit.

Electrical Safet

Dielectric strength:

C 2.0 KV for 1 min, Between Power / In

ut/ Out

ut / Case

Insulation resistance: ≥100M ohm at 500Vdc, Between Power/ In

ut/ Out

Isolation: Between Power / In

ut / Rela

, Analo

ue, RS485

1.0~8.0 mm

FIX HOLDER:

63 mm(L) / W M3

PANEL CU

-OUT:

92+0.2(W) x 44+0.2(H) mm

COM

CI1

ENT/FN

EMC: EN 55011:2002; EN 61326:2003

Safety(LVD): EN 61010-1:2001

CONNECTION DIAGRAM

Environmental

Operating temp.: 0~60 ˚C

Operating humidity: 20~95 %RH, Non-condensing

Temp. coefficient: ≤100 PPM/˚C

Storage temp.: -10~70 ˚C

Enclosure: Front panel: IEC 549 (IP54); Housing: IP20

Mechanical

Dimensions: 96mm(W) x 48mm(H) x 72mm(D)

Panel cutout: 92mm(W) x 44mm(H)

11 12 14 1513 16

SIGNAL INPUT

0~10V

0~20mA Excit.

Supply

DC24V

7 8 9 10

5 64

Relay

b c a

Relay, Analogue o/p

or RS485 port can be

selected one only.

Terminal blocks:

10A/300Vac, M2.6,

1.3~2.0mm2 (16~12AWG)

ADH

C/DC86~265V

C/DC 20~90V

AC230V

AUX. POWER

AC115V

ADL

RS 485

ort

nalogue

output

Case materiel: ABS fire-resistance (UL 94V-0)

Mounting: Panel flush mounting

Terminal block: Plastic NYLON 66 (UL 94V-0)

Please check the voltage of power supplied first, and then connect

to the specified terminals. It is recommended that power supplied to

the meter be protected by a fuse or circuit breaker.

10A 300Vac, M2.6, 1.3~2.0mm2(16~12AWG)

Weight: 350g / 300g(Aux. Power Code: ADH or ADL)

Power

Power supply: AC115/230V,50/60Hz;

Optional: AC/DC 85~264V or 20~90V(RoHS version)

Excitation supply: DC24V/30mA maximum in standard

Power Consumption: 4.5VA maximum

Power Supply

AC115/230V

AC85~264V

Filter or Transformer

1A Fuse

6 7 9 108

Back up memory: By EEPROM

FRONT PANEL

2 wire Transmitter connection RS485 Communication Port

11 12 14 1513

24Vdc

Excit.S

4~20mA

Input

RS485 Port

4 5 6

Max. Distance: 1200M

Terminate Resistor

(at latest unit):

120~300ohm/0.25W

(typical: 150ohm)

I11

ENT/FN

M.H

Comm. status

Relay status

Indication

Operation Key

Front Key

function status

Engineer Unit

Display screen

Max. Hold status

Mini. Hold status

FUNCTION DESCRIPTION

DIMENSIONS Input & Scaling Functions

Dual input types: (Option Code: AV)

Voltage and Current Type are in one unit available in option. If the

customer specify the input coding for AV, the meter will be calibrated for

0~10V and 0~20mA in factory. The user can use in 0~10V or4(0)~20mA

by difference terminals connection(#11 & #13 for 0~10V or #12 & #13 for

4(0)~20mA) and programming in 【Ai.tYP】of【inPUt GroUP】.

Scaling function:

Setting the Lo.SC(Low scale) and Hi.SC(High scale) in【inPUt

GroUP】to relative input signal. Reverse scaling will be done too.

Please refer to the figure as below,

96.0

48.0

92.0+0.2

44.0+0.2

PANEL CUT-OUT

FRONT VIEW

Unit: mm

8.0 12.0

60.0

Dimensions: 96mm x 48mm x 72mm

Panel Cutout: 93mm x 45mm (advise)

SCALE Default: Lo.SC: 0.00, Hi.SC: 100.00

Change to Lo.SC: 50.00, Hi.SC: 199.99

INPUT

0.00

199.99

0.00% 100.00%50.00%

100.00

50.00

Reverse slop

*Too narrow scale may course display lower resolution.

CSM-321S

CS2-

CSM-321S CSM-CSM-

CS1-PR

CSM-321S CSM-CSM-

CSM-321SCSM-

CSM-321S

WWW.100Y.COM.TW WWW.100Y.COM.TW WWW.100Y.COM.TW

C1-01-3

7-2007-11-07

Display & Functions Digital fine adjustment:

Max / Mini recording: The meter will storage the maximum and minimum value in

【User Level】during power on in order to review drifting

of PV.

Display functions: PV / Max(Mini) Hold / RS 485 programmable in

(Please refer to step A-07) 【dSPLY】function of【inPUt GroUP】

Present Value Pv:The display will show the value that

Relativeto Input signal.

Users can get Fine Adjustment for Zero & Span of PV by front key of

the meter, and “Just Key In” the value which user want to show in

the current input signals.

Especially, the【Pv.Zro】&【Pv.SPn】are not only in zero & span of

PV, but also any lower point for【Pv.Zro】& higher point for【Pv.SPn】.

The meter will be linearization for full scale.

The adjustment can be clear in function【Z.S.CLr】.

Maximum Hold Max.H / Minimum Hold Mini.H :

The meter will keep display in maximum(minimum)

value during power on, until press front key to reset

(If the down key function in【inPUt GroUP】has

been set to M.rSt .)

¾Please find the M.H

sticker that enclosure the

package of the meter to stick on the right side of

square orange LED

Default Input: Lo.SC: 0.00, Hi.SC: 199.99

Digital fine adjut.: input 2.75V,

Display: Low point from 55.00 to 80.00

High point from 180.00 tp 170.00

SCALE

INPUT

0.00

199.99

0V 10V5V

100.00

2.75

55.00

150.00

80.00

9.00V

180.00

170.00

Reading Stable Function

Average:

Max. ( Mini.) Hold & Reset

Reset the Max

(Mini) Hold by

E.C.I. or F. Key

Level

Trigger

Maximum Hold

Present

Value

Remote Display by RS485 command RS485 : The

meter will show the value that received from RS485

Basically, the sampling rate of meter is 15cycles/sec. If the function

set to be 3 times, It means the meter will update of display will be 5

times/sec.

sending. In past, The meter normally receive

or 0~10V from AO or digital output from BCD module

of PLC .We support a new solution that PV shows

the value from RS485 command of master can so

that can be save cost and wiring from PLC.

Front key functions: Relative PV / PV Hold / Reset for maxi(mini) hold /

verage set to be 3

Remark: The higher average setting will cause the response time of Relay and Analogue output slower.

Sample 1 Sample 2 Sample 3 Sample 4 Sample 5 Sample 6 …….

Display Update Value =

(Sample 1 + Sample 2 + Sample 3)/3 Display Update Value =

(Sample4 + Sample 5 + Sample 6)/3

Reset for relay energized latch programmable in Moving average:

【dn.KEY】function of 【inPUt GroUP】

Relative PV rEL.Pv :【dn.KEY】function can be set to If the function to be set 3 times, the meter will update delay in first 3

samples, then it will update 15 times/sec continuously.

be rEL.Pv function. When user press the

key,

the display will show the differential value(∆PV), until

press

key again.

¾Please find the R.P

sticker to stick on the right

side of square red LED.

PV Hold Pv. HLd :【dn.KEY】function can be set to

be Pv. HLd function. When user press the

key,

the display will be hold until press the

key again.

¾Please find the PV.H

sticker to stick on the right

Moving Average set to be 3

Remark: The higher moving average setting wouldn’t cause the response time of Relay and Analogue

output slower after first 3 samples.

Sample 1 Sample 2 Sample 3 Sample 4 Sample 5 Sample 6 …….

In first 3 samples, Display Update Value = (Sample 1 + Sample 2 + Sample 3)/3

Display Update Value = (Sample 2 + Sample 3 + Sample 4)/3

Display Update Value = (Sample 3 + Sample 4 + Sample 5)/3

Display Update Value = (Sample 4 + Sample 5 + Sample 6)/3

side of square red LED. Digital filter: The digital filter can reduce the magnetic noise in field.

Control functions(option)

Relay energized mode: Hi / Lo/Hi.HLd /Lo.HLdprogrammable

Hi: Relay will energize when PV > Set-Point

Lo: Relay will energize when PV < Set-Point

PV Hold & Reset

Present

Value

Reset PV Hold

by Front

DownKey O

NEdge

Trigger

ON ON

PV Hold

Reset for Max(Mini) Hold: when the【dSPLY】in

【inPUt GroUP】set to be Max.H or Mini.H ,

【dn.KEY】function can be set to be M.rSt to reset

the display when it is holding in maxim or mini value.

Reset for relay energized latch: when the【rY1.Md】in

【rELAY GroUP】set to be Hi.HLd or Lo.HLd ,

Hi / Lo Relay Energized

Hi Settin

Hi Relay Energized ON

Lo Settin

Lo Relay Energized ON

【dn.KEY】function can be set to be rY.rSt to reset Hi.HLd (Lo.HLd): When the PV is Higher (or lower) than

the relay when it is energizing and latching. set-point, the relay will be energized and latch until

Low cut: manual reset by from key in【User Level】or press

down key to reset(If the 【dn.KEY】function set to

be rY.rSt)

If the setting value is positive, it means when the absolutely value of

PV ≤Setting value, the display will be 0. If the setting value is

negative, it means when the PV under setting value(PV≤-Setting

value), the display will be setting value.

Hi(Lo) Energized Latch & Reset

Hi.HLd(High Hold)

Rela

Ener

ized ON

Reset the relay

Latch by Down Key ON

Level Trigger

Hi Setting

Low Cut set to be +0.50

Low Cut set to be -0.10

-0.10

Low cut

function

Low Cut is set for 0.50, ifthe PV is

from -0.50~+0.50, that display will be 0. Low Cut is set for -0.10, if the PV is under

(< = -0.10),that display will be -0.10.

PV according

to input signal

Present

Value

Low cut

function

0.50

-0.50

Present

Value PVaccording

to input signal

CS2-

CSM-321S CSM-CSM-

CS1-PR

CSM-321S CSM-CSM-

CSM-321SCSM-

CSM-321S

WWW.100Y.COM.TW WWW.100Y.COM.TW WWW.100Y.COM.TW

C1-01-4

7-2007-11-07

Energized functions: Startdelay/Energized&De-energizeddelay/Hysteresis RS 485 Communication(option)

The RS485’s protocol is Modbus RTU mode, and baud rate up to

38400 bps. It’s convenience to remote monitoring, display for

reading.

Start Dela

Energized

De-energized

Delay & Hysteresis

Start Dela

Time

Start Band

Hi Setting

Relay

Energized ON

Inhibit

Energized delaytim

steresis

De-energized

delay time

Hi Setting

Relay

Energized

Analogue output(option)

Please specify the output type either an o~10V or 4(0)~20mA in

ordering. The programmable output low and high scaling can be

based on various display values. Reverse slope output is possible by

reversing point positions.

Output range: Voltage: 0~5V / 0~10V / 1~5V programmable

Current: 0~10mA / 0~20mA / 4~20mA programmable

Functions: Ao.HS(output range high): setting the Display value High

to versus output range High(as like as 20mA in 4~20)

RS 485 Modbus RTU Mode (up to 38400bps)

1 Relay Output:

Mode: High or Low Energized

Functions: Start delay / Energized &

De-energized delay / Hysteresis

Analo

Output 0~10V/0(4)~20mA

Display:

Mode: Measuring Value / Maximum Hold /

Minimum Hold / Reading value from

RS485 command

ENT/

◄

▲

▼

RPM

◄

▲

▼

Kg/cm

Ao.LS(output range Low): setting the Display value Low

to versus output range Low(as like as 4mA in 4~20) Remote display:

The meter will show the value that received from RS485 command.

In past, The meter normally receive 4~20mA or 0~10V from AO or

digital output from BCD module of PLC .We support a new solution

that PV shows the value from RS485 command of master so that

can be save cost and wiring from PLC.

When the【dSPLY】set to be RS485, it means, the PV screen will

show the number from RS485 command & data. The data(number)

will be same as PV that will compare with set-point, analogue output

and ECI functions so that is to control analogue output, relay

energized and so on.

Set Scaling: Lo.SC: 0.00, Hi.SC: 199.99;

Output: Ao.LS: 50.00(Display Value Low),

Ao.HS: 150.00(Display Value High)

0.00% 100.00%50.00% OUTPUT

199.99

100.00

0.00

50.00

150.00

SCALE

The range between Ao.HS and Ao.LS should be over

20% of span at least; otherwise, it will be got less

resolution of analogue output.

Fine zero & span adjustment:

Users can get Fine Adjustment of analogue output by front key of

the meter. Please connect standard meter to the terminal of

analogue output. To press the front key(up or down key) of meter to

adjust and check the output of meter.

【Ao.Zro】:Fine Zero Adjustment for Analog Output;

CS1 APPLICATION FOR REMOTE DISPLAY FROM RS485 COMMAND

RS 485 Modbus RTU Mode (up to 38400bps)

RS485 wiring 1.2KM maximum

Terminate Resistor:

RL1

I11

ENT/FN

◄

▲

▼

M.H

RL1

I11

ENT/FN

◄

▲

▼

M.H

Settable range: -38011~27524;

【Ao.Spn】:Fine Span Adjustment for Analog Output;

Settable range: -38011~27524;

ERROR MASAGE

DESCRIPTION DISPLAY FLASH REMARK

BEFORE POWER ON, PLEASE CHECK THE SPECIFICATION AND

CONNECTION AGAIN.

SELF-DIAGNOSIS AND ERROR CODE:

: Display is positive-overflow (Signal is over display range) (Please check the input signal)

: Display is negative-overflow (Signal is under display range) (Please check the input signal)

: ADC is positive-overflow (Signal is higher than input 120%) (Please check the input signal)

: ADC is negative-overflow (Signal is lower than input -120%) (Please check the input signal)

/ : EEPROM occurs error (Please send back to

manufactory for repaired)

/ : Calibrating Input Signal do not process (Please process Calibrating

Input Signal)

/ : Calibrating Input Signal error (Please check Calibrating Input

Signal)

/ : Calibrating Output Signal do not process (Please process Calibrating

Output Signal)

/ : Calibrating Output Signal error (Please check Calibrating

Output Signal)

CS2-

CSM-321S CSM-CSM-

CS1-PR

CSM-321S CSM-CSM-

CSM-321SCSM-

CSM-321S

WWW.100Y.COM.TW WWW.100Y.COM.TW WWW.100Y.COM.TW

C1-01-5

7-2007-11-07

FRONT PANEL:

I11

ENT/FN

Comm. status

Relay status

Indication

Operation Key

Front Key

function status

Engineer Unit

Display screen

M.H

Max. Hold status

M.H

Mini. Hold status

Numeric Screens

0.8”(20.0mm) red high-brightness LED for 5 digital present

value.

I/O Status Indication

zRelay Energized: 1 square red LED

RL1

display when Relay 1 energized;

zRS485 Communication: 1 square orange LED

will flash when the meter is receive or send data, and CO

flash quickly means the data transient quicker.

zMax/Mini Hold indication: 2 square orange LEDs

M.H

displayed: When the display function has been selected

in Maximum or Minimum Hold function.

Stickers:

Each meter has a sticker what are functions and engineer

label enclosure.

zRelay energized mode: H

Hi L

o L

L D

zDown key functions mode:

PV.H(PV Hold) / Tare / DI(Digital Input)

M.RS(Maximum or Minimum Reset) /

R.RS(Reset for Relay Latch)

zEngineer Label: over 80 types.

Operating Key: 4 keys for

Enter(Function) /

Shift(Escape) /

Up key /

Down key

Setting Status Function Index

Up key Increase number Go back to previous

function index

Down key Decrease number Go to next

function index

Shift key Shift the setting

position Go back to this function

index, and abort the

setting

Enter/Fun

key Setting Confirmed

and save to

EEProm

From the function index

to get into setting status

Pass Word: Settable range:0000~9999;

User has to key in the right pass word so that get into

【Programming Level】. Otherwise, the meter will go back to

measuring page. If user forgets the password, please contact

with the service window.

Function Lock: There are 4 levels programmable.

zNone: no lock all.

zUser Level: User Level lock. User can get into User Level for

checking but setting.

zProgramming Level: Programming level lock. User can get

into programming level for checking but setting.

zALL: All lock. User can get into all level for checking but

setting.

Front Key Function

zThe

Key can be set to be rEL.Pv / Pv.HLd / M.rSt /

rY.rSt programmable.

CS2-

CSM-321S CSM-CSM-

CS1-PR

CSM-321S CSM-CSM-

CSM-321SCSM-

CSM-321S

WWW.100Y.COM.TW WWW.100Y.COM.TW WWW.100Y.COM.TW

C1-01-6

7-2007-11-07

OPERATING DIAGRAM (The detail description of operation, please refer to operating manual.)

Power ON

Self-diagnosis

Show the

model number

0−0−1

This page will

show out,

when dSPLY

set to be

RS485.

Pv: Present

Value

0−3

Min:PV

Minimum

storage

Checking only

0−6

model number

firmware

version

Checking only

Show

the firmware

version

0−1

rY.1.SP.: Relay

1 Set-point

setting

-19999~+29999

0−4

MAX:PV

Maximum

storage

Checking only

0−0−1

Cyclic to first

page

ENT

MEASURING

PAGE

Press

1sec

Press

1sec

0−2

rY.rSt: Reset

for energized

Latch of Relay

YES no

0−5

M.rSt: Reset

for Maximum &

Minimum

storage

YES no

ENT

Enter the

password to

access

programming

Level

Pass Code

Default:1000

ENT

INPUT

GROUP

▲

▼

ENT

RELAY

GROUP

▲

▼

ENT

ANALOGUE

OUTPUT

GROUP

▲

▼

ENT

RS485

GROUP

A−0

Ai.tYP:

Analogue

Input type

selection

v.0-10 v. 0~5

v.1-5 A.0-10

A.0-20 A.4-20

B−1

rY.Sb: Start

band for Relay

energized

0~9999counts

D−1

Ao.Typ:

Analogue

Output type

selection

v.0-10 v. 0~5

v.1-5 A.0-20

A.4-20 A.0-10

E−1

Adres: Device

number of the

meter

1~255

A−1

Pv.dP:

Decimal Point

of PV

0~0.0000

B−2

rY.Sd: Start

delay time for

Relay

energized

0:00.0~

9(m):59.9(s)

D−2

Ao.LS:

Analogue Low

Output versus

Low Scale

-19999~+29999

E−2

baud: Baud

rate

1200 2400

4800 9600

19200 38400

A−2

Lo.SC: Low

scale of PV

-19999~+29999

B−3

rY1.Md: Relay

1 energized

mode

oFF Lo Hi

Lo.HLd Hi.HLd

D−3

Ao.HS:

Analogue High

Output versus

High Scale

-19999~+29999

E−3

PritY: Parity

n.Stb.1

n.Stb.2 odd

EvEn

A−3

Hi.SC: High

scale of PV

-19999~+29999

B−4

rY1.HY.: Relay

1 Hysteresis

0~5000counts

D−4

Ao.Zro: Fine

Zero

djustment for

Analog Low

Output

-38011~+27524

A−4

Pv.Zro: Fine

Low point

Adjustment for

PV display

-19999~+29999

B−5

rY1.rd: Relay 1

energized

delay time

0:00.0~

9(m):59.9(s)

D−5

Ao.SPn: Fine

Span

djustment for

Analog High

Output

-38011~+27524

A−5

Pv.SPn: Fine

High point

Adjustment for

PV display

-19999~+29999

B−6

rY1.Fd: Relay

1 de-energized

delay time

0:00.0~

9(m):59.9(s)

D−6

Z.S.CLr: Zero

& Span Clear

for Adjustment

nonE Ao.Zro

Ao.SPn botH

User Level

Press

for 1 sec. can back to Measuring

Pro

rammin

Level

Press

for 1 sec. can back to Measuring

▼

▲

CS2-

CSM-321S CSM-CSM-

CS1-PR

CSM-321S CSM-CSM-

CSM-321SCSM-

CSM-321S

WWW.100Y.COM.TW WWW.100Y.COM.TW WWW.100Y.COM.TW

C1-01-7

7-2007-11-07

A−6

Z.S.CLr: Clear

Fine Zero &

Span

Adjustment for

PV display

nonE Pv.Zro

Pv.SPn botH

A−7

dSPLY:

Display

Function

Pv Mini.H

MAx.H RS485

A−8

Lo.Cut: Low

Cut Function

-19999~+29999

A−9

AvG: Average

update for PV

1(None)~

99 times

A−10

M.AvG:

Moving

Average

update for PV

1(None)~

10 times

A−11

d.FiLt: Digital

filter

0(None)/1~99

times

A−12

dn.KEY:

Down key

function

nonE rEL.Pv

Pv.HLd M.rSt

rY.rSt

A−13

P.CodE: Pass

Code for enter

Programming

Level

0000~9999

A−14

F.LoCk:

Function Level

Lock

nonE USEr

EnG ALL

¾Plesae refer to operating manual for detail description

CS2-

CSM-321S CSM-CSM-

CS1-PR

CSM-321S CSM-CSM-

CSM-321SCSM-

CSM-321S

WWW.100Y.COM.TW WWW.100Y.COM.TW WWW.100Y.COM.TW

Table of contents

Popular Measuring Instrument manuals by other brands

Fluke

Fluke i800 instruction sheet

REED

REED LM-81HT instruction manual

az-instrument

az-instrument 8758 Operation manual

ISKRAEMECO

ISKRAEMECO MT880 Installation and maintenance manual

Olympus

Olympus USPM-RU-W Series instruction manual

ROOTECH

ROOTECH ACCURA 2700 Quick user guide

Dräger

Dräger X-am 5600 Instructions for use

Galvanic Applied Sciences

Galvanic Applied Sciences 943-TGS-CE Operation manual

twintex

twintex TI512 Operation manual

ATO

ATO PH/ORP user manual

Digi-Sense

Digi-Sense 20250-19 user manual

POOL LAB

POOL LAB V20 user manual

Co2meter

Co2meter XT-10 instruction manual

ATO

ATO YT-1200H user manual

Delta

Delta RetroSign GR1 quick guide

Air TEc

Air TEc Expert CYPRES 2 user guide

Vjoycar

Vjoycar P15 user manual

B+K precision

B+K precision SEFRAM 7861 manual

ADTEK CS1-PR User manual

Popular Measuring Instrument manuals by other brands