Amazone Cayena 6001 User manual
Operating Manual
az
Tine coulter seed drill
Cayena 6001
Cayena 6001-C
MG4235
BAH0062-5 07.20
Please read this
operating manual
before initial operation.
Keep it in a safe place for future use.
en
Cayena 6001/-C BAH0062-5 07.20 3
Identification data
Please insert the identification data of the implement. The
identification data are arranged on the rating plate.
Machine type:
Implement number, ten digits:
Year of manufacture:
Permissible total weight [kg]:
Manufacturer address
AMAZONEN-WERKE
H. DREYER GmbH & Co. KG
Postfach 51
D-49202 Hasbergen
Tel.: + 49 (0) 5405 501-0
E-mail: [email protected]
Spare Parts Order
Spare parts lists are freely accessible in the spare parts portal at
www.amazone.de.
Please send orders to your AMAZONE dealer.
Formalities of the operating manual
Machine type: Cayena 6001/-C
Document number: MG4235
Compilation date: 07.20
Copyright AMAZONEN-WERKE H. DREYER GmbH & Co. KG, 2020
All rights reserved.
Reprinting, even of sections, permitted only with the approval of
AMAZONEN-WERKE H. DREYER GmbH & Co. KG.
4 Cayena 6001/-C BAH0062-5 07.20
Foreword
Dear Customer,
You have chosen one of the quality products from the wide product range of AMAZONEN-WERKE,
H. Dreyer GmbH & Co. KG. We thank you for your trust in our products.
On receiving the implement, check to see if it has been damaged during transport or if parts are
missing. Using the delivery note, check that the implement has been delivered in full, including any
special equipment ordered. Damage can only be rectified if problems are claimed immediately.
Before initial operation, read and comply with the information in this operating manual, and particularly
the safety instructions. Only after careful reading will you be able to benefit from the full scope of your
newly purchased implement.
Please ensure that all the implement operators have read this operating manual before they put the
implement into operation.
If there are any questions or problems, please read this operating manual or contact your local service
partner.
Regular maintenance and timely replacement of worn or damaged parts increases the service life of
your implement.
Cayena 6001/-C BAH0062-5 07.20 5
1User information ........................................................................................ 10
2General Safety Information ....................................................................... 11
2.1Obligations and liability .......................................................................................................... 11
2.2Representation of safety symbols .......................................................................................... 13
2.3Organisational measures ....................................................................................................... 14
2.4Safety and protective equipment ........................................................................................... 14
2.5Informal safety measures ....................................................................................................... 14
2.6User training ........................................................................................................................... 15
2.7Safety measures in normal operation .................................................................................... 16
2.8Danger from residual energy ................................................................................................. 16
2.9Maintenance and repair work, fault elimination ..................................................................... 16
2.10Design changes ..................................................................................................................... 16
2.10.1Spare and wear parts and aids .............................................................................................. 17
2.11Cleaning and disposal ............................................................................................................ 17
2.12Workstation of the operator .................................................................................................... 17
2.13Warning symbols on the implement ....................................................................................... 18
2.13.1Position of warning symbols .................................................................................................. 2 5
2.14Dangers in case of non-compliance with the safety instructions ........................................... 27
2.15Safety-conscious working ...................................................................................................... 27
2.16Safety information for users ................................................................................................... 28
2.16.1General safety instructions and accident prevention instructions .......................................... 28
2.16.2Hydraulic system .................................................................................................................... 32
2.16.3Electrical system .................................................................................................................... 33
2.16.4Attached implements ............................................................................................................. 33
2.16.5Service brake system ............................................................................................................. 34
2.16.6Tyres ...................................................................................................................................... 35
2.16.7Operation of the seed drill ...................................................................................................... 35
2.16.8PTO shaft operation (fan drive via PTO shaft) ....................................................................... 35
2.16.9Cleaning, maintenance and repair ......................................................................................... 36
3Loading and unloading the low-bed trailer for delivery ......................... 37
3.1Preparing the implement for loading and unloading .............................................................. 37
3.2Loading the flat-bed trailer ..................................................................................................... 38
3.3Unloading the implement ....................................................................................................... 39
4Product description ................................................................................... 40
4.1Main assembly groups of the implement ............................................................................... 40
4.2Safety and protective equipment ........................................................................................... 44
4.3Overview – Supply lines between the tractor and the implement .......................................... 45
4.4Transportation equipment ...................................................................................................... 47
4.5Safety device against unauthorised use ................................................................................ 48
4.6Proper use .............................................................................................................................. 4 9
4.7Danger areas and danger points ........................................................................................... 50
4.8Rating plate and CE mark ...................................................................................................... 51
4.9Technical data ........................................................................................................................ 53
4.9.1Road transport data ............................................................................................................... 53
4.10Required tractor equipment ................................................................................................... 5 4
4.11Noise production data ............................................................................................................ 54
5Structure and function .............................................................................. 55
5.1AMADRILL+ control terminal ................................................................................................. 56
5.2Control terminal for implements with ISOBUS system .......................................................... 57
5.2.1AMAZONE AmaTron 4 control terminal ................................................................................. 57
5.2.2AMAZONE TwinTerminal ....................................................................................................... 58
6 Cayena 6001/-C BAH0062-5 07.20
5.2.3AMAZONE mySeeder app .................................................................................................... 58
5.3Service brake system ............................................................................................................ 59
5.3.1Parking brake ........................................................................................................................ 59
5.3.2Dual circuit pneumatic service brake system ........................................................................ 60
5.3.3Hydraulic service brake system ............................................................................................ 60
5.3.4Implements without service brake system ............................................................................ 60
5.4Implement documentation ..................................................................................................... 61
5.5Radar ..................................................................................................................................... 61
5.6Tractor wheel mark eradicator .............................................................................................. 62
5.7Leading guide wheels ........................................................................................................... 62
5.8Cutting discs .......................................................................................................................... 63
5.9Trailing roller with integrated running gear ............................................................................ 64
5.9.1Furrow ridge leveller .............................................................................................................. 64
5.9.2Scraper .................................................................................................................................. 65
5.10Hopper ................................................................................................................................... 65
5.10.1One chamber hopper ............................................................................................................ 65
5.10.2Two chamber hopper ............................................................................................................ 66
5.10.3Monitoring the hopper content .............................................................................................. 67
5.12Metering ................................................................................................................................ 69
5.12.1.1Metering roller diagram table - figures .................................................................................. 71
5.12.1.2Table – metering rollers, seed ............................................................................................... 74
5.12.2Table – Fertiliser metering rollers .......................................................................................... 75
5.12.3Calibrating the spread rate .................................................................................................... 76
5.12.4Calibration – One-chamber system ....................................................................................... 77
5.12.5Calibration – Two-chamber system ....................................................................................... 78
5.12.5.1Metering operation - Two-chamber system during operation ............................................... 78
5.13Fan ........................................................................................................................................ 79
5.13.1Fan speed table for one chamber system ............................................................................. 80
5.13.2Fan speed table for two chamber system ............................................................................. 81
5.13.3Connecting the fan to the tractor hydraulics ......................................................................... 82
5.13.4Fan connection to the tractor PTO shaft (on-board hydraulic system) ................................. 83
5.14Distributor head ..................................................................................................................... 84
5.14.1Seed tube monitoring ............................................................................................................ 84
5.15TineTeC tine coulters ............................................................................................................ 85
5.16Exact following harrow .......................................................................................................... 86
5.16.1Exact following harrow tine position ...................................................................................... 86
5.16.2Exact following harrow pressure ........................................................................................... 87
5.17Rear harrow ........................................................................................................................... 87
5.18Track marker ......................................................................................................................... 88
5.19Seeding variations adjustable on the control terminal .......................................................... 89
5.19.1Adapting the seeding rate to the acceleration of the tractor ................................................. 89
5.19.2Seeding a corner on the field ................................................................................................ 89
5.20Tramlines ............................................................................................................................... 90
5.20.1Tramline rhythm, tabular determination ................................................................................ 92
5.20.2Tramline rhythm, graphic determination................................................................................ 92
5.20.3One-sided switching .............................................................................................................. 94
5.20.4Tramline marker .................................................................................................................... 95
5.21Work floodlights ..................................................................................................................... 95
6Initial operation .......................................................................................... 96
6.1Checking the suitability of the tractor .................................................................................... 97
6.1.1Calculation of the actual values for the total tractor weight, tractor axle loads and
tyre load-bearing capacity, as well as the required minimum ballast weight ........................ 98
6.1.1.1Data required for the calculation (hitched implement) .......................................................... 99
6.1.1.2Calculation of the required minimum ballast weight at the front GV min of the tractor
to ensure steering capability ............................................................................................... 100
6.1.1.3Calculation of the actual front axle load of the tractor TV tat ................................................. 100
6.1.1.4Calculation of the actual total weight of the combined tractor and implement .................... 100
6.1.1.5Calculation of the actual rear axle load of the tractor TH tat ................................................. 100
Cayena 6001/-C BAH0062-5 07.20 7
6.1.1.6Load-bearing capacity of the tractor tyres ........................................................................... 100
6.1.1.7Table .................................................................................................................................... 101
6.1.2Requirements for tractor operation with trailed implements ................................................ 102
6.2Secure the tractor / implement against unintentional starting and rolling away .................. 103
6.3Fan drive - Hydraulic connection ......................................................................................... 104
7Coupling and uncoupling the implement .............................................. 105
7.1Dual circuit pneumatic service brake system ....................................................................... 106
7.1.1Coupling the brake and supply lines .................................................................................... 108
7.1.2Uncoupling the supply and brake line .................................................................................. 109
7.1.3Control elements for the dual circuit pneumatic service brake system................................ 110
7.2Hydraulic service brake system ........................................................................................... 111
7.2.1Coupling the hydraulic service brake system ...................................................................... 111
7.2.2Uncoupling the hydraulic service brake system ................................................................... 113
7.3Hydraulic hose lines ............................................................................................................. 115
7.3.1Coupling the hydraulic hose lines ........................................................................................ 115
7.3.2Uncoupling the hydraulic hose lines .................................................................................... 116
7.4Coupling the implement to the tractor .................................................................................. 117
7.5Uncoupling the implement ................................................................................................... 122
7.6Connect/disconnect the PTO shaft driven hydraulic pump .................................................. 124
7.6.1Connecting the hydraulic pump ........................................................................................... 125
7.6.2Uncoupling the hydraulic pump............................................................................................ 125
8Settings ..................................................................................................... 126
8.1Moving the tractor wheel mark eradicator into working and transport position ................... 126
8.1.1Moving the tractor wheel mark eradicator into working position .......................................... 126
8.1.2Moving the tractor wheel mark eradicator into transport position ........................................ 127
8.2Setting the working depth of the cutting discs ..................................................................... 127
8.3Repositioning the low level sensor ...................................................................................... 128
8.4Installing/removing the metering roller ................................................................................. 128
8.5Calibrating the spread rate ................................................................................................... 131
8.5.1Calibration methods - Overview ........................................................................................... 131
8.5.2Calibration - Seed drills with one metering unit and one distributor head ........................... 132
8.5.3Calibration - Seed drills with two metering units and one distributor head .......................... 133
8.6Adjusting the fan speed ....................................................................................................... 134
8.6.1Setting the fan speed - On the flow control valve of the tractor ........................................... 135
8.6.2Setting the fan speed - Tractors without flow control valve ................................................. 135
8.6.3Setting the fan speed - Connection to the tractor PTO shaft ............................................... 135
8.6.4Pressure relief valve with round outer contour .................................................................... 136
8.6.4.1Basic setting of the pressure relief valve ............................................................................. 136
8.6.4.2Fan speed setting ................................................................................................................ 136
8.6.5Pressure relief valve with hexagonal outer contour ............................................................. 137
8.6.5.1Basic setting of the pressure relief valve ............................................................................. 137
8.6.5.2Fan speed setting ................................................................................................................ 137
8.6.6Fan speed monitoring .......................................................................................................... 138
8.6.7Pressure monitoring in the two chamber hopper ................................................................. 138
8.7Adjusting the seed placement depth .................................................................................... 139
8.8Exact following harrow ......................................................................................................... 140
8.8.1Exact following harrow tine position ..................................................................................... 140
8.8.2Exact following harrow pressure adjustment ....................................................................... 140
8.9Adjusting the rear harrow ..................................................................................................... 141
8.10Track marker ........................................................................................................................ 142
8.11One-sided switching ............................................................................................................. 143
8.11.1Implement one-sided switch-off ........................................................................................... 143
8.12Adjusting the tramline marker .............................................................................................. 144
8.12.1Moving the tramline marker into working position ................................................................ 144
8.12.2Moving the tramline marker into transport position .............................................................. 144
8.13Moving the road safety bar into transport/parking position .................................................. 145
8 Cayena 6001/-C BAH0062-5 07.20
8.13.1Moving the road safety bar to transport position ................................................................. 145
8.13.2Moving the road safety bar into parking position ................................................................ 146
9Transportation ......................................................................................... 147
9.1Set the implement to road transport mode .......................................................................... 147
9.2Legal requirements for road transport ................................................................................. 148
9.3Safety during road transport ................................................................................................ 150
10Use of the implement .............................................................................. 152
10.1Initial operation .................................................................................................................... 154
10.2Work floodlights ................................................................................................................... 154
10.3Moving the implement into working position ....................................................................... 155
10.4Unfolding/folding the implement booms .............................................................................. 156
10.4.1Unfolding the implement sections - AMADRILL+ ................................................................ 156
10.4.2Folding the implement sections - AMADRILL+ ................................................................... 158
10.4.3Unfolding the implement sections - ISOBUS ...................................................................... 160
10.4.4Folding the implement sections - ISOBUS .......................................................................... 161
10.5Filling the hopper ................................................................................................................. 163
10.5.1Opening/closing the roller tarpaulin ..................................................................................... 164
10.5.2Opening the hopper cover ................................................................................................... 165
10.5.3Close the hopper cover ....................................................................................................... 166
10.6During operation .................................................................................................................. 167
10.6.1Check points ........................................................................................................................ 167
10.6.2Checking the placement depth of the seed ......................................................................... 167
10.6.3Turning at end of the field ................................................................................................... 168
10.7End of work on the field ....................................................................................................... 169
10.8Emptying the hopper and/or the metering unit .................................................................... 169
11Faults ........................................................................................................ 171
11.1Residual seed volume indicator .......................................................................................... 171
11.2Deviations between the preset and actual seeding rates ................................................... 172
11.3Fault table ............................................................................................................................ 172
12Maintenance and repairs ........................................................................ 173
12.1Maintenance schedule ........................................................................................................ 173
12.2Greasing points – overview ................................................................................................. 175
12.3Safety .................................................................................................................................. 177
12.3.1Securing the connected implement ..................................................................................... 178
12.3.2Securing the implement when raised with the integrated running gear .............................. 179
12.3.3Safety when cleaning the implement .................................................................................. 179
12.3.4Safety when working on the hydraulic system .................................................................... 180
12.3.5Safety when working on the service brake system ............................................................. 180
12.4Visual inspections ................................................................................................................ 181
12.4.1Visual inspection of the tensioned crosspiece .................................................................... 181
12.4.2Visual and functional check of the service brake system (all versions) .............................. 181
12.4.3Visual check of the hydraulic hose lines and couplings ...................................................... 182
12.4.3.1Date of manufacture of the hydraulic hose line ................................................................... 182
12.5Repairs ................................................................................................................................ 183
12.5.1Cleaning the fan suction protective screen ......................................................................... 183
12.5.2Cleaning the fan rotor .......................................................................................................... 183
12.5.3Clean the oil cooler.............................................................................................................. 183
12.5.4Cleaning the distributors head and checking the seed hoses for impurities ...................... 184
12.5.5Check the tyre inflation pressure of the leading guide wheels ............................................ 185
12.5.6Check the inflation pressure of the wedge ring tyres .......................................................... 185
12.5.7On-board hydraulics – Oil check and oil filter change ......................................................... 186
12.6Installations ......................................................................................................................... 188
12.6.1Setting the track marker for correct threading into the transport bracket ........................... 188
12.6.2Shutdown of the implement over a long period of time ....................................................... 188
12.7Workshop work .................................................................................................................... 189
Cayena 6001/-C BAH0062-5 07.20 9
12.7.1Drawbar pipe length adjustment .......................................................................................... 189
12.7.2Checking the tightening torques of the wheel and hub screws ........................................... 189
12.7.3Adjusting the tramline track width of the cultivating tractor .................................................. 190
12.7.4Adjusting the tramline wheelmark width of the cultivating tractor ........................................ 191
12.7.4.1Activating or deactivating shutters: ...................................................................................... 192
12.7.5Checking the hydraulic hose lines ....................................................................................... 193
12.7.5.1Safety when working on hydraulic hose lines ...................................................................... 194
12.7.6Check the service brake system (all versions) for operational safety.................................. 195
12.7.7Dual circuit pneumatic service brake system ....................................................................... 195
12.7.7.1Exterior inspection of the compressed air tank .................................................................... 195
12.7.7.2Check the pressure in the compressed air tank .................................................................. 196
12.7.7.3Leak tightness check ........................................................................................................... 196
12.7.7.4Cleaning the line filter .......................................................................................................... 196
12.8Oils and greases .................................................................................................................. 197
12.8.1Lubricants for grease nipples and grease guns ................................................................... 197
12.9Bolt tightening torques ......................................................................................................... 198
13Hydraulic diagram .................................................................................... 200
13.1Hydraulic diagram Cayena 6001 with AMADRILL+ ............................................................. 200
13.2Hydraulic diagram - Cayena 6001(-C) with ISOBUS system .............................................. 202
User information
10 Cayena 6001/-C BAH0062-5 07.20
1 User information
The User information section provides information concerning the operating manual.
This operating manual is valid for all versions of the implement.
Figures serve as a reference and are to be understood as representations of the principle.
All of the equipment is described without indicating it as special equipment. A description may be
provided for equipment that is not fitted on the implement or is only available in certain markets. The
sales documents provide information on the equipment of your implement or consult your service
partner for more detailed information.
All information in this operating manual corresponds to the state of knowledge at the time of
publication. Due to ongoing development of the implement, deviations are possible between the
implement and the information in this operating manual. No claims can be made based on differences
in the specifications, figures or descriptions.
If you want to sell the implement, ensure that the operating manual is supplied with the implement.
The operating manual
describes the operation and maintenance of the implement
provides important information on safe and efficient handling of the implement
is an integral part of the implement and should always be kept with the implement or the towing
vehicle
must be kept in a safe place for future use.
Activities to be carried out by the user are presented as numbered instructions. Always observe the
sequence of the instructions. The reaction to instructions is indicated by an arrow where applicable.
Example:
1. Instruction 1
Reaction of the implement to handling instruction 1
2. Instruction 2
Listings without a mandatory sequence are presented as a listing with bullets.
Example: Point 1
Point 2
Numbers in round brackets refer to the item numbers in the illustrations. The first number refers to the
diagram and the second number to the item.
Example: (Fig. 3/6) = Figure 3 / Position 6
All the directions specified in the operating manual are always viewed in the direction of travel.
General Safety Information
Cayena 6001/-C BAH0062-5 07.20 11
2 General Safety Information
This section contains important information on safe operation of the implement.
2.1 Obligations and liability
Comply with the instructions in the operating manual
Knowledge of the basic safety information and safety regulations is a basic requirement for safe
handling and fault-free implement operation.
Obligations of the operator
The operator is obliged only to let those people work with/on the implement who
are aware of the basic workplace safety information and accident prevention regulations
have been trained in working with/on the implement
have read and understood this operating manual.
The operator is obliged
to keep all the warning symbols on the implement in a legible state
to replace damaged warning symbols.
Obligations of the user
Before starting work, anyone charged with working with/on the machine is obliged
to comply with the basic workplace safety instructions and accident prevention regulations
to read and understand the "General safety information" section of this operating manual
to read the section "Warning symbols and other labels on the implement" in this operating
manual and to follow the safety instructions represented by the warning symbols when operating
the implement
to get to know the implement
to read the sections of this operating manual, important for carrying out your work.
If the user discovers that a function is not working properly, then they must eliminate this fault
immediately. If this is not the task of the user or if the user does not have the appropriate technical
knowledge, then they should report this fault to their superior (operator).
General Safety Information
12 Cayena 6001/-C BAH0062-5 07.20
Risks in handling the implement
The implement has been constructed to the state-of-the art and the recognised rules of safety.
However, operating the implement may cause risks and restrictions
the health and safety of the user or third persons
the implement itself
other property.
Only use the implement
for the purpose for which it was intended
in a perfect state of repair.
Eliminate any faults immediately which could impair safety.
Guarantee and liability
Our "General conditions of sales and delivery" are always applicable. These shall be available to the
operator, at the latest on conclusion of the contract. Guarantee and liability claims for damage to
people or property will be excluded if they can be traced back to one or more of the following causes:
Improper use of the implement
Improper installation, commissioning, operation and maintenance of the implement
Operation of the implement with defective safety equipment or improperly attached or non-
functioning safety and protective equipment
Non-compliance with the instructions in the operating manual regarding commissioning,
operation and maintenance
Unauthorised design changes to the implement
Insufficient monitoring of implement parts which are subject to wear
Improperly executed repairs
Disasters due to the effects of foreign objects and force majeure.
General Safety Information
Cayena 6001/-C BAH0062-5 07.20 13
2.2 Representation of safety symbols
Safety information is indicated by the triangular safety symbol and the highlighted signal word. The
signal word (DANGER, WARNING, CAUTION) describes the severity of the risk, and carries the
following meaning:
DANGER
Indicates an immediate hazard with high risk, which will result
in death or serious bodily harm (loss of limbs or long-term
harm), if it is not avoided.
If the instructions are not followed, then this will result in
immediate death or serious physical injury.
WARNING
Indicates a medium risk, which could result in death or (serious)
physical injury if not avoided.
If the instructions are not followed, then this may result in death
or serious physical injury.
CAUTION
Indicates a low risk which could cause minor or medium level
physical injury or damage to property if not avoided.
IMPORTANT
Indicates an obligation to special behaviour or an activity required for
proper implement handling.
Non-compliance with these instructions can cause faults on the
implement or disturbance to the environment.
NOTE
Indicates handling tips and particularly useful information.
These instructions will help you to use all the functions of your
implement in the best way possible.
General Safety Information
14 Cayena 6001/-C BAH0062-5 07.20
2.3 Organisational measures
The operator must provide the necessary personal protective equipment as per the information
provided by the manufacturer of the crop protection agent to be used, such as:
Safety glasses
Protective shoes
Chemical-resistant overalls
Skin protection agents, etc.
The operating manual
must always be kept at the place at which the implement is
operated
must always be easily accessible for the user and maintenance
personnel.
Check all the available safety equipment regularly.
2.4 Safety and protective equipment
Before starting up the implement each time, all the safety and protection equipment must be properly
attached and fully functional. Check all safety and protection equipment regularly.
Faulty safety equipment
Faulty or disassembled safety and protection equipment can lead to dangerous situations.
2.5 Informal safety measures
As well as all the safety information in this operating manual, comply with the general, national
regulations pertaining to accident prevention and environmental protection.
When driving on public roads and routes you should comply with the statutory road traffic regulations.
General Safety Information
Cayena 6001/-C BAH0062-5 07.20 15
2.6 User training
Only those people who have been trained and instructed may work with/on the implement. The
operator must clearly specify the responsibilities of the people charged with operation and
maintenance work.
People being trained may only work with/on the implement under the supervision of an experienced
person.
Person
Activity
Person
specially trained
for the activity 1)
Trained
operator 2)
Person with specialist
training (specialist
workshop) 3)
Loading/Transport X X X
Initial operation X
Set-up, tool installation X
operation X
Maintenance X
Troubleshooting and fault
elimination
X X
Disposal X
Key: X..permitted ..not permitted
1) A person who can assume a specific task and who can carry out this task for an appropriately
qualified company.
2) Instructed persons are those who have been instructed in their assigned tasks and in the
possible risks in the case of improper behaviour, have been trained if necessary, and have been
informed about the necessary protective equipment and measures.
3) Persons with specialised technical training shall be considered as a specialist. Due to their
specialist training and their knowledge of the appropriate regulations, they can evaluate the work
with which they have been charged and detect possible dangers.
Comment:
A qualification equivalent to specialist training can be obtained from several years' experience in
the relevant field.
Only a specialist workshop may carry out maintenance and repair
work on the implement, if such work is additionally marked
"Specialist workshop". The personnel of a specialist workshop shall
possess the appropriate knowledge and suitable aids (tools, lifting
and support equipment) for carrying out the maintenance and repair
work on the implement in a way which is both appropriate and safe.
General Safety Information
16 Cayena 6001/-C BAH0062-5 07.20
2.7 Safety measures in normal operation
Only operate the implement if all the safety and protection equipment is fully functional.
Check the implement at least once a day for visible damage and check the function of the safety and
protection equipment.
2.8 Danger from residual energy
Note that there may be residual mechanical, hydraulic, pneumatic and electrical/electronic energy on the
implement.
Use appropriate measures to inform the operator. You can find detailed information in the relevant
sections of this operating manual.
2.9 Maintenance and repair work, fault elimination
Carry out prescribed setting, maintenance and inspection work in good time.
Secure all media such as compressed air and the hydraulic system against unintentional start-up.
Carefully fix and secure larger assembly groups to lifting units when carrying out replacement work.
Check all the bolted connections for tightness. On completion of the maintenance work, check the
function of the safety and protective devices.
2.10 Design changes
You may make no changes, expansions or modifications to the implement without the authorisation of
AMAZONEN-WERKE. This also applies when welding support parts.
Any extension or conversion work shall require the written approval of AMAZONEN-WERKE. Only use
conversion and special equipment parts approved by AMAZONEN-WERKEN so that the operating
permit, for example, remains valid in accordance with national and international regulations.
Vehicles with an official type approval or with equipment connected to a vehicle with a valid type
approval or approval for road transport according to the German road traffic regulations must be in the
state specified by the approval.
WARNING
Risk of crushing, cutting, being trapped or drawn in, or impact
through the failure of support parts.
It is strictly forbidden to
drill holes in the frame or on the running gear
increase the size of existing holes on the frame or the running gear
weld on load-bearing parts.
General Safety Information
Cayena 6001/-C BAH0062-5 07.20 17
2.10.1 Spare and wear parts and aids
Immediately replace any implement parts which are not in a perfect state.
Use only genuine AMAZONE spare and wear parts or the parts cleared by AMAZONEN-WERKE so
that the operating permit retains its validity in accordance with national and international regulations. If
you use wear and spare parts from third parties, there is no guarantee that they have been designed
and manufactured in such a way as to meet the requirements placed on them.
AMAZONEN-WERKE shall accept no liability for damage caused by the use of non-approved spare
and wear parts or aids.
2.11 Cleaning and disposal
Handle and dispose of any materials used carefully, in particular
when carrying out work on lubrication systems and equipment and
when cleaning using solvents.
2.12 Workstation of the operator
The implement may be operated by only one person sitting in the driver's seat of the tractor.
General Safety Information
18 Cayena 6001/-C BAH0062-5 07.20
2.13 Warning symbols on the implement
Always keep all the warning symbols of the implement clean and in a
legible state. Replace illegible warning symbols. You can request the
warning symbols from your AMAZONE dealer using the order number
(e.g., MD 075).
Structure
Warning symbols indicate danger areas on the implement and warn against residual dangers. At these
points, there are permanent or unexpected dangers.
A warning symbol consists of two fields.
Field 1
Shows the danger in a triangular safety symbol.
Field 2
Shows instructions for avoiding the danger.
Explanatory text beside the warning symbol
The text beside the warning symbol describes
1. The dangers, e.g.:
Laceration or amputation hazard.
2. The consequence of non-compliance with the risk avoidance instructions, e.g.:
This danger can cause serious injuries to fingers or hands.
3. Instructions for avoiding the risk, e.g.:
Touch machinery parts only when they have come to a complete stop.
General Safety Information
Cayena 6001/-C BAH0062-5 07.20 19
MD 078
Risk of crushing of fingers/hand by
accessible, moving parts of the implement!
This hazard can cause extremely serious injuries
resulting in the loss of limbs.
Never reach into the danger area when the
tractor engine is running with the universal joint
shaft or hydraulic / electronic system connected.
MD 082
Risk of falling when riding the implement on
treads or platforms!
Causes serious, potentially fatal injuries
anywhere on the body.
It is forbidden to ride on the implement or climb
the implement when it is running. This prohibition
also applies to implements with step surfaces or
platforms.
Make sure that nobody is riding on the
implement.
MD 084
Risk of crushing the entire body due to
standing in the swivel range when implement
parts are being lowered.
Causes serious, potentially fatal injuries
anywhere on the body.
It is forbidden to stand in the swivel range of
the implement when implement parts are
being lowered.
Instruct personnel to leave the swivel range
of any implement parts which can be
lowered before you lower the parts.
General Safety Information
20 Cayena 6001/-C BAH0062-5 07.20
MD 094
Risk of electric shock or burns from
accidentally touching overhead power lines
or by coming within the prohibited distance
of high voltage overhead power lines.
These dangers can cause extremely serious and
potentially fatal injuries.
Maintain a sufficient distance from electrical
overhead cables when swinging any parts of the
implement in and out.
Rated voltage Safety distance from
transmission lines
up to 1 kV
over 1 up to 110 kV
over 110 up to 220 kV
over 220 up to 380 kV
1 m
3 m
4 m
5 m
MD 095
Before commissioning the machine read and
observe the operating manual and the safety
instructions carefully!
Other manuals for Cayena 6001
1
This manual suits for next models
1
Table of contents
Other Amazone Farm Equipment manuals
Amazone
Amazone AW 6600 User manual
Amazone
Amazone EDX 9000-TC User manual
Amazone
Amazone Groundkeeper GHL User manual
Amazone
Amazone AD-P 303 Super User manual
Amazone
Amazone CatrosXL 3003 Installation instructions
Amazone
Amazone ZA-M Ultra User manual
Amazone
Amazone Catros 3002-T User manual
Amazone
Amazone Cataya 3000 Super Installation instructions
Amazone
Amazone Certos 4002-2TX User manual
Amazone
Amazone XTender 2200 User manual
Amazone
Amazone CatrosXL 4003-2 Installation instructions
Amazone
Amazone Cenius 4002-2T Super User manual
Amazone
Amazone Tyrok 400 OL Quick guide
Amazone
Amazone Precea 3000-A Installation instructions
Amazone
Amazone CombiDisc 3000 Installation instructions
Amazone
Amazone TL 3000 User manual
Amazone
Amazone Cayros M Installation instructions
Amazone
Amazone UX 7601 Super User manual
Amazone
Amazone KE 3002 Installation instructions
Amazone
Amazone ZA-M premiS User manual
