Amazone Certos 4002-2TX User manual

Operating Manual
az
Certos 4002-2TX
Certos 5002-2TX
Certos 6002-2TX
Certos 7002-2TX
Trailed compact disc harrow
MG6905
BAG0219.3
07.21
Printed in Germany
Read and observe this
operating manual before using
the implement
for the first time!
Keep it in a safe place for
future use!
en-US

2
Certos BAG0219.3
07.21
Reading the instruc-
tion
manual and to adhere to it should not appear to
be inconvenient and superfluous as it is not
enough to hear from others and to realise that a
implement is good, to buy it and to believe that
now everything would work by itself. The person
concerned would not only harm himself but also
make the mistake of blaming the implement for
the reason of a possible failure instead of himself.
In order to ensure a good success one should go
into the mind of a thing or make himself familiar
with every part of the implement and to get ac-
quainted with its handling. Only this way, you
would be satisfied both with the implement as al-
so with yourself. To achieve this is the purpose of
this instruction manual.
Leipzig-Plagwitz 1872.

Identification data
Certos
BAG0219.3 07.21
3
Identification data
Manufacturer:
AMAZONEN-WERKE
H. DREYER SE & Co. KG
Implement identification no.:
Type:
Certos
Year of manufacture:
Factory:
Basic weight
Approved total weight
Maximum load:
Manufacturer's address
AMAZONEN-WERKE
H. DREYER SE & Co. KG
Postfach 51
D-49202
Phone:
E-mail:
Hasbergen
+ 49 (0) 5405 50 1-0
[e-mail]
Spare part orders
Spare parts lists are freely accessible in the spare parts portal at
www.amazone.de.
Please send orders to your AMAZONE dealer.
Formalities of the operating manual
Document number:
MG6905
Compilation date:
07.21

Copyright AMAZONEN-WERKE H. DREYER SE & Co. KG, 2021
All rights reserved.
Reprinting, even of sections, permitted only with the approval of
AMAZONEN-WERKE H. DREYER SE & Co. KG.

Foreword
4
Certos BAG0219.3
07.21
Foreword
Dear Customer,
You decided to purchase one of our high quality implements from the
comprehensive range of farm implementry produced by AMAZONEN-
WERKE, H. DREYER SE & Co. KG. We thank you for your confi-
dence in our products.
On receiving the implement, check to see if it was damaged during
transport or if parts are missing. Using the delivery note, check that
the implement was delivered in full including the ordered special
equipment. Replacement will be made only if a claim is filed immedi-
ately!
Please read and follow this operating manual—in particular, the safe
ty
instructions—before putting the implement into operation. Only after
careful reading will you be able to benefit from the full scope of your
newly purchased implement.
Please ensure that all the implement operators have read this operat-
ing manual before they put the implement into operation.
Should you have any questions or problems, please consult this op-
erating manual or contact your local service partner.
Regular maintenance and timely replacement of worn or damaged
parts increases the lifespan of your implement.
User evaluation
Dear Reader
We update our operating manuals regularly. Your suggestions for
improvement help us to create ever more user-friendly manuals.
AMAZONEN-WERKE
H. DREYER SE & Co. KG
Postfach 51
D-49202
Phone:
E-mail:
Hasbergen
+ 49 (0) 5405 50 1-0
[e-mail]

Table of Contents
Certos
BAG0219.3 07.21
5
1User information ..........................................................................................8
1.1 Purpose of the document.........................................................................................................8
1.2 Locations in the operating manual...........................................................................................8
1.3 Diagrams used.........................................................................................................................8
2General safety instructions.........................................................................9
2.1 Obligations and liability ............................................................................................................9
2.2 Representation of safety symbols..........................................................................................11
2.3 Organisational measures .......................................................................................................12
2.4 Safety and protection equipment ...........................................................................................12
2.5 Informal safety measures.......................................................................................................12
2.6 User training...........................................................................................................................13
2.7 Safety measures in normal operation ....................................................................................14
2.8 Dangers from residual energy................................................................................................14
2.9 Maintenance and repair work, fault elimination .....................................................................14
2.10 Constructive changes ............................................................................................................14
2.10.1 Spare and wear parts and aids ..............................................................................................15
2.11 Cleaning and disposal............................................................................................................15
2.12 User workstation ....................................................................................................................15
2.13 Warning pictograms and other signs on the implement ........................................................16
2.13.1 Positioning of warning pictograms and other labels ..............................................................16
2.14 Dangers of not observing safety instructions.........................................................................22
2.15 Safety-conscious working ......................................................................................................22
2.16 Safety information for users ...................................................................................................23
2.16.1 General safety and accident prevention information .............................................................23
2.16.2 Hydraulic system....................................................................................................................26
2.16.3 Electrical system ....................................................................................................................27
2.16.4 Coupled implements ..............................................................................................................28
2.16.5 Brake system .........................................................................................................................29
2.16.6 Tires .......................................................................................................................................30
2.16.7 Cleaning, maintenance and repairs .......................................................................................30
3Loading and unloading .............................................................................31
4Product description ...................................................................................32
4.1 Overview of subassemblies ...................................................................................................32
4.2 Safety and protection equipment ...........................................................................................34
4.3 Supply lines between the tractor and the implement .............................................................35
4.4 Transportation equipment ......................................................................................................35
4.5 Intended use ..........................................................................................................................36
4.6 Danger area and danger points .............................................................................................37
4.7 Rating plate and CE mark......................................................................................................38
4.8 Technical data........................................................................................................................39
4.8.1 Payload and tire load capacity ...............................................................................................40
4.9 Necessary tractor equipment .................................................................................................42
4.10 Noise production data ............................................................................................................42
5Structure and function ..............................................................................43
5.1 Function .................................................................................................................................43
5.2 Hydraulic connections............................................................................................................44
5.2.1 Coupling hydraulic hose lines ................................................................................................45
5.2.2 Disconnecting hydraulic hose lines........................................................................................45
5.3 Dual-circuit service brake system ..........................................................................................46
5.3.1 Coupling the brake and supply lines ......................................................................................47
5.3.2 Uncoupling the brake and supply lines ..................................................................................48

Table of Contents
6
Certos BAG0219.3
07.21
5.4 Hydraulic service brake system ............................................................................................ 49
5.4.1 Coupling the hydraulic service brake system........................................................................ 49
5.4.2 Uncoupling the hydraulic operating brake system ................................................................ 49
5.4.3 Emergency brake .................................................................................................................. 50
5.5 Parking brake ........................................................................................................................ 51
5.6 Two-row disc cultivator.......................................................................................................... 51
5.7 Side elements for levelling .................................................................................................... 52
5.8 Crushboard (option) .............................................................................................................. 52
5.9 Roller ..................................................................................................................................... 53
5.10 Working without the roller...................................................................................................... 55
5.11 Rear harrow (optional)........................................................................................................... 57
5.12 Running gear......................................................................................................................... 58
5.13 Drawbar ................................................................................................................................. 59
5.13.1 Hydraulic drawbar control ..................................................................................................... 60
5.14 Swing compensation ............................................................................................................. 61
5.15 Hydraulic lateral pull compensation ...................................................................................... 62
5.16 Jack ....................................................................................................................................... 62
5.17 Supporting wheels (option) ................................................................................................... 63
5.18 Safety chain between tractor and implements ...................................................................... 64
5.19 Safety device against unauthorised use ............................................................................... 64
5.20 Hectare counter (optional)..................................................................................................... 65
5.21 GreenDrill catch crop seeding unit ........................................................................................ 66
6Commissioning ......................................................................................... 67
6.1 Checking the suitability of the tractor .................................................................................... 68
6.1.1 Calculating the actual values for the total tractor weight, tractor axle loads and load
capacities, as well as the minimum ballast ........................................................................... 68
6.1.2 Requirements for tractor operation with attached implements.............................................. 72
6.2 Securing the tractor/implement against unintentional start-up and rolling ............................ 76
7Coupling and uncoupling the implement................................................ 77
7.1 Coupling the implement ........................................................................................................ 77
7.2 Uncoupling the implement..................................................................................................... 80
8Adjustments............................................................................................... 82
8.1 Adjusting the working depth of the discs............................................................................... 82
8.1.1 Hydraulic working depth adjustment ..................................................................................... 82
8.1.2 Manual working depth adjustment ........................................................................................ 83
8.2 Intensity of the crushboard .................................................................................................... 85
8.3 Adjusting the side elements .................................................................................................. 86
8.4 Adjusting the scraper of the rollers........................................................................................ 87
8.5 Height of towing eye.............................................................................................................. 87
9Transportation ........................................................................................... 88
10 Use of the implement................................................................................ 90
10.1 Transport to working position ................................................................................................ 91
10.1.1 Changing from transport to working position ........................................................................ 91
10.1.2 Changing from working to transport position ........................................................................ 92
10.1.3 Moving the right side disc into transport position / working position ..................................... 93
10.1.4 Certos 7002-2TX: Moving the outer discs into transport position / working position ............ 93
10.1.5 Move the spacer elements on the running gear into the transport position / working
position (working without a roller).......................................................................................... 94
10.2 Operation............................................................................................................................... 95
10.3 Headland ............................................................................................................................... 95
10.4 Preventing lateral pull............................................................................................................ 96

Table of Contents
Certos
BAG0219.3 07.21
7
11 Faults ..........................................................................................................97
12 Cleaning, maintenance and repairs..........................................................98
12.1 Cleaning .................................................................................................................................99
12.2 Lubrication instructions ........................................................................................................100
12.3 Maintenance plan - overview ...............................................................................................102
12.4 Axle (running gear / support wheel) and brake....................................................................104
12.4.1 Inspection instructions for the dual-circuit service brake system.........................................109
12.4.2 Hydraulic brakes ..................................................................................................................110
12.4.3 Axle bolts..............................................................................................................................110
12.5 Checking the roller ...............................................................................................................110
12.6 Check the coupling device ...................................................................................................111
12.7 Parking brake .......................................................................................................................112
12.8 Tires / wheels .......................................................................................................................113
12.8.1 Tire air pressure ...................................................................................................................113
12.8.2 Fitting tires (workshop work) ................................................................................................114
12.9 Replacing discs (workshop work) ........................................................................................114
12.10 Hydraulic system (workshop work) ......................................................................................115
12.10.1 Labelling hydraulic hose lines ..............................................................................................116
12.10.2 Maintenance intervals ..........................................................................................................116
12.10.3 Inspection criteria for hydraulic hose lines ...........................................................................116
12.10.4 Installation and removal of hydraulic hose lines ..................................................................117
12.11 Upper- / Lower link pins .......................................................................................................117
12.12 Screw tightening torques .....................................................................................................118

User information
8
Certos BAG0219.3
07.21
1 User information
The "User information" section supplies information on using the op-
erating manual.
1.1 Purpose of the document
This operating manual
•Describes the operation and maintenance of the implement.
• Provides important information on safe and efficient handling of
the implement.
•Is a component part of the implement
and should always be kept
with the implement or the traction vehicle.
• Keep it in a safe place for future use.
1.2 Locations in the operating manual
All the directions specified in the operating manual are always viewed
in the direction of travel.
1.3 Diagrams used
Instructions for action and reactions
Tasks to be carried out by the user are presented as numbered in-
structions. Always keep to the order of the instructions. The reaction
to instructions is given by an arrow. Example:
1. Instruction for action 1
→Reaction of the implement to instruction for action 1
2. Instruction for action 2
Lists
Lists without a mandatory sequence a presented as a list with bullet
points. Example:
• Point 1
• Point 2
Item numbers in diagrams
Numbers in round brackets refer to the item numbers in the diagrams.
The first digit refers to the diagram; the second digit, to the item num-
ber in the illustration.
Example (6)
→Item 6

General safety instructions
Certos
BAG0219.3 07.21
9
2 General safety instructions
This section contains important information on safe operation of the
implement.
2.1 Obligations and liability
Comply with the instructions in the operating manual
Knowledge of the basic safety information and safety regulations is a
basic requirement for safe handling and fault-free implement opera-
tion.
Obligations of the operator
The operator is obliged only to let those people work with/on the im-
plement who
• Are aware of the basic workplace safety information and acci-
dent prevention regulations.
•Have been introduced to working with/on the implement.
•Have read and understood this operating manual.
The operator is obliged
• To keep all the warning pictograms on the implement
in a legible
state.
• To replace damaged warning pictograms.
Obligations of the user
Before starting work, anyone charged with working with/on the imple-
ment is obliged
• To comply with the basic workplace safety instructions and acci-
dent prevention regulations.
•To read and observe the section "General safety information" of
this operating manual.
•To read the section "Warning symbols and other labels on the
implement" (page 17) of this operating manual and to follow the
safety instructions represented by the warning symbols when
operating the implement.
•To get to know the implement.
• To read the sections of this operating manual, important for car-
rying out your work.
If the user discovers that a function is not working properly, then they
must eliminate this fault immediately. If this is not the task of the user
or if the user does not possess the appropriate technical knowledge,
then they should report this fault to their superior (operator).

General safety instructions
10
Certos BAG0219.3
07.21
Risks in handling the implement
The implement has been constructed to the state-of-the art and the
recognised rules of safety. However, there may be risks and re-
strictions which occur when operating the implement
•For the health and safety of the user or third persons,
• For the implement,
• For other goods.
Only use the implement
• For the purpose for which it was intended.
•In a perfect state of repair.
Eliminate any faults that could impair safety immediately.
Guarantee and liability
Our "General conditions of sales and business" are always applicable.
These shall be available to the operator, at the latest on the comple-
tion of the contract. Guarantee and liability claims for damage to peo-
ple or goods will be excluded if they can be traced back to one or
more of the following causes:
•Improper use of the implement.
• Improper installation, commissioning, operation and mainte-
nance of the implement.
•Operation of the implement with defective safety equipment or
improperly attached or non-functioning safety equipment.
•Non-compliance with the instructions in the operating manual
regarding commissioning, operation and maintenance.
•Independently-executed construction changes to the implement.
• Insufficient monitoring of implement parts that are subject to
wear.
•Improperly executed repairs.
• Catastrophic events as a result of the impact of foreign objects
or force majeure.

General safety instructions
Certos
BAG0219.3 07.21
11
2.2 Representation of safety symbols
Safety instructions are indicated by the triangular safety symbol and
the highlighted signal word. The signal word (DANGER, WARNING,
CAUTION) describes the gravity of the risk and has the following sig-
nificance:
DANGER
Indicates an immediate high risk, which will result in death or
serious physical injury (loss of body parts or long term damage)
if not avoided.
If the instructions are not followed, then this will result in imme-
diate death or serious physical injury.
WARNING
Indicates a medium risk, which could result in death or (serious)
physical injury if not avoided.
If the instructions are not followed, then this may result in death
or serious physical injury.
CAUTION
Indicates a low risk, which could incur minor or medium level
physical injury or damage to property if not avoided.
IMPORTANT
Indicates an obligation to special behaviour or an activity re-
quired for proper implement handling.
Non-compliance with these instructions can cause faults on the
implement or in the environment.
NOTE
Indicates handling tips and particularly useful information.
These instructions will help you to use all the functions of your
implement to the optimum.

General safety instructions
12
Certos BAG0219.3
07.21
2.3 Organisational measures
The operator must provide the necessary personal protective equip-
ment, such as:
•Protective goggles,
•Safety shoes,
•Protective overall,
•Skin protection cream, etc..
The instruction manual
• Must always be kept at the place at which the implement is
operated.
• Must always be easily accessible for the user and mainte-
nance personnel.
Check all the available safety equipment regularly.
2.4 Safety and protection equipment
Before each commissioning of the implement, all the safety and pro-
tection equipment must be properly attached and fully functional.
Check all the safety and protection equipment regularly.
Faulty safety equipment
Faulty or disassembled safety and protection equipment can lead to
dangerous situations.
2.5 Informal safety measures
As well as all the safety information in this operating manual, comply
with the general, national regulations pertaining to accident prevention
and environmental protection.
When driving on public roads and ro
utes, then you should comply with
the statutory road traffic regulations.

General safety instructions
Certos
BAG0219.3 07.21
13
2.6 User training
Only trained and instructed persons should be allowed to work with/on
the implement. The responsibilities of the operating and maintenance
personnel must be clearly defined.
People being trained may only work with/on the implement under the
supervision of an experienced person.
People
Activity
Particularly
trained
persons1)
Instructed
operator 2)
Persons with specialist
training
(authorised workshop) 3)
Loading/Transport X X X
Commissioning -- X --
Set-up, tool installation -- -- X
Operation -- X --
Maintenance -- -- X
Troubleshooting and fault elimina-
tion
X -- X
Disposal X -- --
Legend:
X..permitted
--..not permitted
1) A person who can assume a specific task and who can carry out
this task for an appropriately qualified company.
2) Instructed persons are those who have been instructed in their
assigned tasks and in the possible risks in the case of improper
behaviour, have been trained if necessary, and have been in-
formed about the necessary protective equipment and
measures.
3) People with specialist technical training shall be considered as a
specialist. Due to their specialist training and their knowledge of
the appropriate regulations, they can evaluate the work with
which they have been charged and detect possible dangers.
Comment:
A qualification equivalent to specialist training can be obtained
through long term activity in the appropriate field of work.
Only a specialist workshop may carry out maintenance and repair
work on the implement, if such work is specifically designated "Work-
shop work". The personnel of a specialist workshop shall possess the
appropriate knowledge and suitable aids (tools, lifting and support
equipment) for carrying out the maintenance and repair work on the
implement in a way which is both appropriate and safe.

General safety instructions
14
Certos BAG0219.3
07.21
2.7 Safety measures in normal operation
Only operate the implement if all the safety and protection equipment
is fully functional.
Check the implement at least once a day for visible damage and
check the function of the safety and protection equipment.
2.8 Dangers from residual energy
Note that there may be residual mechanical, hydraulic, pneumatic and
electrical/electronic energy at the implement.
Use appropri
ate measures to inform the operating personnel. You can
find detailed information in the relevant sections of this operating
manual.
2.9 Maintenance and repair work, fault elimination
Carry out prescribed setting, maintenance and inspection work in a
timely manner.
Secure all media such as compressed air and the hydraulic system
against unintentional start-up.
Carefully fix and secure larger subassemblies to lifting gear when
carrying out replacement work.
Regularly check that bolted connections are firmly secured and tight-
en if necessary.
When the maintenance work is completed, check the function of the
safety devices.
2.10 Constructive changes
You may make no changes, expansions or modifications to the im-
plement without the authorisation of AMAZONEN-WERKE. This is
also valid when welding support parts.
Any expansion or modification work shall require the written approval
of AMAZONEN-WERKE. Only use the modification and accessory
parts released by AMAZONEN-WERKE so that the operating permit,
for example, remains valid in accordance with national and interna-
tional regulations.
Vehicles with an official type approval or with equipment connected to
a vehicle with a valid type approval or approval for road transport
according to the German road traffic regulations must be in the state
specified by the approval.
WARNING
Risk of being crushed, cut, caught, drawn in or struck if support-
ing parts break.
It is forbidden to:
• Drill holes in the frame or on the chassis.
•Increasing the size of existing holes on the frame or the chassis.
•Welding support parts.

General safety instructions
Certos
BAG0219.3 07.21
15
2.10.1 Spare and wear parts and aids
Immediately replace any implement parts which are not in a perfect
state.
Use only genuine AMAZONE spare and wear parts or parts approved
by AMAZONEN-WERKEN to ensure that the operating permit retains
its validity in accordance with national and international regulations. If
you use wear and spare parts from third parties, there is no guarantee
that they have been designed and manufactured in such a way as to
meet the requirements placed on them.
AMAZONEN-WERKE accepts no liability for damage arising from the
use of unapproved spare parts, wear parts or auxiliary materials.
2.11 Cleaning and disposal
Handle and dispose of any materials used carefully, in particular:
• When carrying out work on lubrication systems and equipment
and
•When cleaning using solvents.
2.12 User workstation
The implement must be operated by only one person from the driver's
seat of the tractor.

General safety instructions
16
Certos BAG0219.3
07.21
2.13 Warning pictograms and other signs on the implement
2.13.1 Positioning of warning pictograms and other labels
The following diagrams show the arrangement of the warning picto-
grams on the implement.

General safety instructions
Certos
BAG0219.3 07.21
17
Always keep all the warning pictograms of the implement
clean and in
a legible state. Replace illegible warning pictograms. You can obtain
the warning pictograms from your dealer using the order number
(e.g. MD 078).
Warning pictorial - structure
Warning labels indicate dangers on and around the implement and
warn for hazards. At these points, there are permanent and/or
unexpected dangers.
A warning pictorial consists of four fields:
Field 1
a pictorial depicting the danger.
Field 2
shows the safety alert symbol along with a signal word which indi-
cates the level of danger.
Field 3
explains the type of hazard, as well as how to avoid it.
Field 4
is where the order number is located.
Warning pictorial - explanation
In the following pages, the individual warning labels will be explained
in more detail. The column on the left, Order number and
explanation, provides an explanation of the warning pictorial on the
right. The description of the warning labels always follows the same
order:
1. The order number.
For example: MO007
2. The hazard is shown in bold when applicable.
For example: High Pressurized Fluid Hazard
3. Instructions for avoiding the danger.
For example: Do not use hands to locate leaks.

General safety instructions
18
Certos BAG0219.3
07.21
Order number and explanation
Warning pictorial
MO001 WARNING
•Read and understand the operator’s manu-
al before operating this implement.
•Lire et comprendre le manuel d’utilisation
avant d’utiliser cette implement.
•Lea y comprenda el manual de operation
antes de usa resta maquina.
MO002 WARNING
CRUSH HAZARD
•Make sure nobody is in the danger area
when attaching the implement to the tractor.
MO003 WARNING
MOVING WING HAZARD
•Make sure nobody is in the danger area.
MD004 WARNING
PINCH HAZARD
•Secure tractor and implement and wait until
all parts have stopped before reaching into
danger area:
•Make sure nobody is in the danger area or
near any moving parts.
MO006 WARNING
CUTTING HAZARD
•Secure tractor and implement until all parts
have stopped before reaching into danger
area:
•Make sure nobody is in the danger area or
near any moving parts.

General safety instructions
Certos
BAG0219.3 07.21
19
MO007 WARNING
HIGH PRESSURE HYDRAULIC OIL
IS HAZARDOUS
•Never use your hands to locate or plug any
leak in the hydraulic hoses.
•If hydraulic oil penetrates your skin, seek
immediate medical attention.
MO008 WARNING
FALL HAZARD
•Never ride on the implement.
•Keep others from climbing onto or riding on
the implement.
MO009 WARNING
RUN-AWAY HAZARD
•Secure implement from accidental rolling.
•Use parking blocks or chocks to secure
implement.
MO010 WARNING
ELECTROCUTION HAZARD
•Never touch any power line with the imple-
ment.
•Always keep a safe distance from all power
lines during transport and folding or unfold-
ing the implement’s components.
•Note that the voltage can also flash over
when the distance is too small.
MO011 WARNING
LIFTING POINT

General safety instructions
20
Certos BAG0219.3
07.21
MO014 WARNING
HYDRAULIC SYSTEM POWER
•Avoid hydraulic system failures and serious
injuries. Never exceed the maximum hy-
draulic system pressure of
3045 psi or 210 bar
MO016 WARNING
•Be sure to secure the tractor and the im-
plement before working on the implement.
MO017 WARNING
LIFT POINT
MO020 WARNING
FALLING HAZARD
To prevent serious injury or death:
•Do not climb on the finishing roller wheels
or finishing roller support.
•Keep others away from the finishing rollers
and finishing roller supports.