Amazone ZG-TS 5500 WAB User manual

Operating Manual
az
ZG-TS 5500 WAB
ZG-TS 8200 WAB
Large-area fertiliser spreader for mounting on a HGV
MG5980
BAG0168.1
08.17
Printed in German
y
Please read this operating
manual before first commi
s-
sioning.
Keep it in a safe place for
fu
ture use.
en

2
ZG-TS BAG0168.1 08.17
Reading the instruction
Manual and following it should seem to be in-
convenient and superfluous as it is not
enough
to hear from others and to realize that a
machine is good, to buy it and to believe that now
everything should work by itself. The person in
question would not only harm himself but also
make the mistake of blaming the machine for pos-
sible failures instea
d of himself. In order to ensure
success one should enter the mind of a thing,
make himself familiar with every part of the ma-
chine and get acquainted with how it's handled.
Only in this way could you be satisfied both with
the machine and with yourself. T
his goal is the
purpose of this instruction manual.
Leipzig-Plagwitz 1872.

Identification data
ZG-TS BAG0168.1 08.17
3
Identification data
Manufacturer:
AMAZONEN-WERKE
H. DREYER GmbH & Co. KG
Machine Ident. No.:
Type:
ZG-TS 8200 WAB
Year of manufacture:
Factory:
Basic weight (kg):
Approved total weight (kg):
Maximum load (kg):
Manufacturer's address
AMAZONEN-WERKE
H. DREYER GmbH & Co. KG
Postfach 51
D-49202
Tel.:
E-mail:
Hasbergen
+ 49 (0)5405 501-0
[e-mail]
Spare part orders
Spare parts lists are freely accessible in the spare parts portal at
www.amazone.de.
Please send orders to your AMAZONE dealer.
Formalities of the operating manual
Document number:
MG5980
Compilation date:
08.17

Copyright AMAZONEN-WERKE H. DREYER GmbH & Co. KG, 2017
All rights reserved.
Reprinting, even of sections, only possible with the approval of AMA-
ZONEN-WERKE H. DREYER GmbH & Co. KG.

Foreword
4
ZG-TS BAG0168.1 08.17
Foreword
Dear Customer,
You have chosen one of the quality products from the wide product
range of AMAZONEN-WERKE, H. DREYER GmbH & Co. KG. We
thank you for your confidence in our products.
On receiving the machine, check to see if it was damaged during
transport or if parts are missing. Using the delivery note, check that
the machine was delivered in full including the ordered special equip-
ment. Damage can only be rectified if problems are signalled immedi-
ately!
Before first commissioning, read and understand this operating man-
ual, and particularly the safety information. Only after careful reading
will you be able to benefit from the full scope of your newly purchased
machine.
Please ensure that all the machine operators have read this operating
manual before commissioning the machine.
Should you have any questions or problems, please consult this op-
erating manual or contact your local service partner.
Regular maintenance and timely replacement of worn or damaged
parts increases the lifespan of your machine.
User evaluation
Dear Reader,
We update our operating manuals regularly. Your suggestions for
improvement help us to create ever more user-friendly manuals.
AMAZONEN-WERKE
H. DREYER GmbH & Co. KG
Postfach 51
D-49202
Tel.:
E-mail:
Hasbergen
+ 49 (0)5405 501-0
[e-mail]

Table of Contents
ZG-TS BAG0168.1 08.17
5
1User Information..........................................................................................7
1.1 Purpose of the document.........................................................................................................7
1.2 Locations in the operating manual...........................................................................................7
1.3 Diagrams used.........................................................................................................................7
2General safety instructions.........................................................................8
2.1 Obligations and liability ............................................................................................................8
2.2 Representation of safety symbols..........................................................................................10
2.3 Organisational measures.......................................................................................................11
2.4 Safety and protection equipment...........................................................................................11
2.5 Informal safety measures.......................................................................................................11
2.6 Operator training....................................................................................................................12
2.7 Safety measures in normal operation....................................................................................12
2.8 Danger from residual energy .................................................................................................13
2.9 Maintenance and repair work, fault elimination .....................................................................13
2.10 Design changes .....................................................................................................................13
2.10.1 Spare and wear parts and auxiliary materials........................................................................14
2.11 Cleaning and disposal............................................................................................................14
2.12 Operator workstation..............................................................................................................14
2.13 Warning symbols and other labels on the machine...............................................................15
2.13.1 Positions of warning symbols and other labels......................................................................16
2.14 Dangers if the safety information is not observed..................................................................20
2.15 Safety-conscious working......................................................................................................20
2.16 Safety information for the operator ........................................................................................21
2.16.1 General safety and accident prevention information .............................................................21
2.16.2 Hydraulic system....................................................................................................................22
2.16.3 Electrical system....................................................................................................................22
2.16.4 Fertiliser spreader operation..................................................................................................23
2.16.5 Cleaning, maintenance and repairs.......................................................................................23
3Mounting on a carrier vehicle...................................................................24
3.1 Loading with a lifting crane / mounting the spreader on the carrier vehicle ..........................24
3.2 Mounting dimensions.............................................................................................................26
3.3 Required HGV equipment......................................................................................................28
3.4 Adjusting the hydraulic system with the system setting screw..............................................30
4Product description...................................................................................32
4.1 Overview of subassemblies...................................................................................................32
4.2 Safety and protection equipment...........................................................................................33
4.3 Transportation equipment......................................................................................................33
4.4 Intended use ..........................................................................................................................34
4.5 Danger areas .........................................................................................................................35
4.6 Rating plate............................................................................................................................35
4.7 Technical data........................................................................................................................36
4.7.1 Weights basic machine and modules ....................................................................................36
4.8 Noise production data............................................................................................................36
5Structure and function ..............................................................................37
5.1 Function .................................................................................................................................37
5.2 Setting chart...........................................................................................................................38
5.3 Spreading discs TS................................................................................................................42
5.4 Agitator...................................................................................................................................43
5.5 Spread rate metering .............................................................................................................44
5.6 Calibration kit (option)............................................................................................................45

Table of Contents
6
ZG-TS BAG0168.1 08.17
5.7 Drop-point system ................................................................................................................. 45
5.8 In-cab terminal....................................................................................................................... 46
5.9 Hydraulically driven conveyor belt......................................................................................... 46
5.10 Foldable ladder...................................................................................................................... 47
5.11 Charging sieves..................................................................................................................... 47
5.12 Ascent with platform.............................................................................................................. 48
5.13 Swivelable hopper cover (optional)....................................................................................... 49
5.14 Control block and machine computer.................................................................................... 49
5.15 Argus Twin (optional) ............................................................................................................ 50
6Adjustments............................................................................................... 51
6.1Setting the spread rate.......................................................................................................... 53
6.2 Spread rate control (fertiliser calibration).............................................................................. 53
6.3 Setting the spreading disc speed.......................................................................................... 53
6.4 Setting the working width ...................................................................................................... 54
6.4.1 Replacing the spreading discs.............................................................................................. 54
6.4.2 Setting the feed system......................................................................................................... 55
6.4.3 Checking the working width with the mobile test rig (optional) ............................................. 55
6.5 Boundary, ditch and side spreading...................................................................................... 56
6.5.1 Settings for border spreading................................................................................................ 57
6.5.2 Adapting the settings for boundary spreading ...................................................................... 59
6.5.3 Switch ClickTS ...................................................................................................................... 59
6.6 Switch-on point and switch-off point...................................................................................... 60
7Transportation........................................................................................... 62
8Use of the machine ................................................................................... 63
8.1 Filling the machine ................................................................................................................ 64
8.2 Spreading operation.............................................................................................................. 65
8.3 Notes for spreading slug pellets (e.g. Mesurol) .................................................................... 68
8.4 Complete discharging............................................................................................................ 69
9Faults.......................................................................................................... 70
9.1 Eliminating agitator malfunctions .......................................................................................... 70
9.2 Faults in electronics............................................................................................................... 70
9.3 Faults, causes and remedies ................................................................................................ 71
10 Cleaning, maintenance and repairs......................................................... 72
10.1 Cleaning ................................................................................................................................ 73
10.2 Lubrication point overview..................................................................................................... 74
10.3 Maintenance schedule – overview........................................................................................ 75
10.4 Replacing the spreading vanes............................................................................................. 76
10.5 Belt conveyor with automatic belt control.............................................................................. 77
10.6 Checking the control butterfly valve, outlet openings and agitator ....................................... 78
10.7 Hydraulic system................................................................................................................... 79
10.7.1 Labelling hydraulic hose lines ............................................................................................... 80
10.7.2 Maintenance intervals ........................................................................................................... 81
10.7.3 Inspection criteria for hydraulic hose lines............................................................................ 81
10.7.4 Installation and removal of hydraulic hose lines ................................................................... 82
10.7.5 Mounting hose fittings with O-rings and sleeve nuts............................................................. 82
10.8 Hydraulic fluid filter................................................................................................................ 83
10.9 Conveyor belt gearbox.......................................................................................................... 83
10.10 Oil change angular gearbox.................................................................................................. 84
10.11 Screw tightening torques....................................................................................................... 85
11 Hydraulic diagram..................................................................................... 86

User Information
ZG-TS BAG0168.1 08.17
7
1 User Information
The User Information section provides information on use of the oper-
ating manual.
1.1 Purpose of the document
This operating manual
•Describes the operation and maintenance of the machine.
•Provides important information on safe and efficient handling of
the machine.
•Is a component part of the machine and should always be kept
with the machine or the traction vehicle.
•Keep it in a safe place for future use.
1.2 Locations in the operating manual
All the directions specified in the operating manual are always seen
from the direction of travel.
1.3 Diagrams used
Operator control action and responses
Actions to be carried out by the operator are given as a numbered list.
It is important that the sequence of steps is observed. The responses
for each operator control action are given by an arrow. Example:
1. Operator control action step 1
→Machine response to operator control action 1
2. Operator control action step 2
Lists
Lists without an essential order are shown as a list with bullets. Ex-
ample:
•Point 1
•Point 2
Number items in diagrams
Numbers in round bracket refer to items in diagrams. The first number
refers to the diagram and the second number to the item in the figure.
Example: (Fig. 3/6)
•Figure 3
•Item 6

General safety instructions
8
ZG-TS BAG0168.1 08.17
2 General safety instructions
This section contains important information on safe operation of the
machine.
2.1 Obligations and liability
Comply with the instructions in the operating manual
Knowledge of the basic safety information and safety regulations is a
basic requirement for safe handling and fault-free machine operation.
Obligations of the operator
The operator is obliged only to let those people work with/on the ma-
chine who
•Are aware of the basic workplace safety information and acci-
dent prevention regulations.
•Have been trained in working with/on the machine.
•Have read and understood this operating manual.
The operator is obliged
•To keep all the warning symbols on the machine in a legible
state.
•To replace damaged warning symbols.
Obligations of the user
Before starting work, anyone charged with working with/on the ma-
chine is obliged
•To comply with the basic workplace safety instructions and acci-
dent prevention regulations.
•To read and follow the "General safety information" section of
this operating manual.
•To read the section "Warning symbols and other labels on the
machine" (page 15) of this operating manual and to follow the
safety instructions represented by the warning symbols when
operating the machine.
•If you still have queries, please contact the manufacturer.

General safety instructions
ZG-TS BAG0168.1 08.17
9
Risks in handling the machine
The machine has been constructed to the state-of-the art and the
recognised rules of safety. However, there may be risks and re-
strictions which occur when operating the machine
•For the health and safety of the operator or third persons,
•For the machine,
•For other goods.
Only use the machine
•For the purpose for which it was intended.
•In a perfect state of repair.
Eliminate any faults immediately which could impair safety.
Guarantee and liability
Our "General conditions of sales and delivery" are always applicable.
These shall be available to the operator, at the latest on the comple-
tion of the contract. Guarantee and liability claims for damage to peo-
ple or goods will be excluded if they can be traced back to one or
more of the following causes:
•Improper use of the machine.
•Improper installation, commissioning, operation and mainte-
nance of the machine.
•Operation of the machine with defective safety equipment or
improperly attached or non-functioning safety equipment.
•Non-compliance with the instructions in the operating manual
regarding commissioning, operation and maintenance.
•Independently-executed design changes to the machine.
•Insufficient monitoring of machine parts which are subject to
wear.
•Improperly executed repairs.
•Disasters through the impact of foreign bodies and acts of God.

General safety instructions
10
ZG-TS BAG0168.1 08.17
2.2 Representation of safety symbols
Safety instructions are indicated by the triangular safety symbol and
the highlighted signal word. The signal word (danger, warning, cau-
tion) describes the severity of the risk, and carries the following mean-
ing:
DANGER
Indicates an immediate high risk which will result in death or
serious physical injury (loss of body parts or long term damage)
if not avoided.
If the instructions are not followed, then this will result in imme-
diate death or serious physical injury.
WARNING
Indicates a medium risk, which could result in death or (serious)
physical injury if not avoided.
If the instructions are not followed, then this may result in death
or serious physical injury.
CAUTION
Indicates a low risk which could cause minor or medium level
physical injury or damage to property if not avoided.
IMPORTANT
Indicates an obligation to special behaviour or an activity re-
quired for proper machine handling.
Non-compliance with these instructions can cause faults on the
machine or in the environment.
NOTE
Indicates handling tips and particularly useful information.
These instructions will help you to use all the functions of your
machine to the optimum.

General safety instructions
ZG-TS BAG0168.1 08.17
11
2.3 Organisational measures
The operator must provide the necessary personal protective equip-
ment as per the information provided by the manufacturer of the crop
protection agent to be used, such as:
•Chemical-resistant gloves,
•Chemical-resistant overalls,
•Water-resistant footwear,
•A face mask,
•Breathing protection,
•Safety glasses,
•Skin protection agents, etc.
The operating manual
•Must always be kept at the place at which the machine is oper-
ated.
•Must always be easily accessible for the operator and mainte-
nance personnel.
Check all the available safety equipment regularly.
2.4 Safety and protection equipment
Before each commissioning of the machine, all the safety and protec-
tion equipment must be properly attached and fully functional. Check
all the safety and protection equipment regularly.
Faulty safety equipment
Faulty or disassembled safety and protection equipment can lead to
dangerous situations.
2.5 Informal safety measures
As well as all the safety information in this operating manual, comply
with the general, national regulations pertaining to accident prevention
and environmental protection.
When driving on public roads and routes, then you should comply with
the statutory road traffic regulations.

General safety instructions
12
ZG-TS BAG0168.1 08.17
2.6 Operator training
Only those people who have been trained and instructed may work
with/on the machine. The operator must clearly specify the responsi-
bilities of the people charged with operation and maintenance work.
People being trained may only work with/on the machine under the
supervision of an experienced person.
People
Activity
Person special-
ly trained for the
activity1)
Trained opera-
tor2) Person with specialist
training
(specialist workshop*)3)
Loading/Transport X X X
Commissioning -- X --
Set-up, tool installation -- -- X
Operation -- X --
Maintenance -- -- X
Troubleshooting and fault elimina-
tion X -- X
Disposal X -- --
Legend: X..permitted --..not permitted
1) A person who can assume a specific task and who can carry out
this task for an appropriately qualified company.
2) Instructed persons are those who have been instructed in their
assigned tasks and in the possible risks in the case of improper
behaviour, have been trained if necessary, and have been in-
formed about the necessary protective equipment and
measures.
3) People with specialist technical training shall be considered as a
specialist. Due to their specialist training and their knowledge of
the appropriate regulations, they can evaluate the work with
which they have been charged and detect possible dangers.
Comment:
A qualification equivalent to specialist training can be obtained
through long term activity in the appropriate field of work.
Only a specialist workshop may carry out maintenance and repair
work on the machine if such work is additionally marked "Workshop
work". The personnel of a specialist workshop shall possess the ap-
propriate knowledge and suitable aids (tools, lifting and support
equipment) for carrying out the maintenance and repair work on the
machine in a way which is both appropriate and safe.
2.7 Safety measures in normal operation
Only operate the machine if all the safety and protection equipment is
fully functional.
Check the machine at least once a day for visible damage and check
the function of the safety and protection equipment.

General safety instructions
ZG-TS BAG0168.1 08.17
13
2.8 Danger from residual energy
Note that there may be residual mechanical, hydraulic, pneumatic and
electrical/electronic energy on the machine.
Use appropriate measures to inform the operatin
g personnel. You can
find detailed information in the relevant sections of this operating
manual.
2.9 Maintenance and repair work, fault elimination
Carry out prescribed setting, maintenance and inspection work in
good time.
Secure all media such as compressed air and the hydraulic system
against unintentional start-up.
Carefully fix and secure larger subassemblies to lifting gear when
carrying out replacement work.
Regularly check that bolted connections are firmly secured and tight-
en if necessary.
When the maintenance work is completed, check the function of the
safety devices.
2.10 Design changes
You may make no changes, expansions or modifications to the ma-
chine without the approval of AMAZONEN-WERKE. This is also valid
when welding support parts.
Any expansion or modification work shall require the written approval
of AMAZONEN-WERKE. Only use the modification and accessory
parts released by AMAZONEN-WERKE, so that the type approval
remains valid according to the national and international regulations.
Vehicles with an official type approval or with equipment connected to
a vehicle with a valid type approval or approval for road transport
according to the German road traffic regulations must be in the state
specified by the approval.
WARNING
Risk of contusions, cuts, dragging, catching or knocks from
support parts.
It is forbidden to:
•Drill holes in the frame or on the running gear.
•Increase the size of existing holes on the frame or the running
gear.
•Weld support parts.

General safety instructions
14
ZG-TS BAG0168.1 08.17
2.10.1 Spare and wear parts and auxiliary materials
Immediately replace any machine parts which are not in a perfect
state.
Only use AMAZONE spare and wear parts released by AMAZONEN-
WERKE, so that the type approval remains valid according to the
national and international regulations. The use of wear and spare
parts from third parties does not guarantee that they have been con-
structed in a way as to meet the requirements placed on them.
AMAZONEN-WERKE shall accept no liability for damage caused by
the use of unreleased spare and wear parts or auxiliary materials.
2.11 Cleaning and disposal
Handle and dispose of any materials used carefully, in particular
•When carrying out work on lubrication systems and equipment
and
•When cleaning using solvents.
2.12 Operator workstation
The machine may only be operated by one person sitting in the driv-
er's seat of the tractor.

General safety instructions
ZG-TS BAG0168.1 08.17
15
2.13 Warning symbols and other labels on the machine
Always keep all the warning symbols on the machine clean and in a
legible state. Replace illegible warning symbols. You can obtain the
warning symbols from your dealer using the order number (e.g. MD
075).
Warning symbols - structure
Warning symbols indicate dangers on the machine and warn against
residual dangers. At these points, there are permanent or unexpected
dangers.
A warning symbol consists of two fields:
Field 1
is a symbol describing the danger, surrounded by triangular safety
symbol.
Field 2
is a symbol showing how to avoid the danger.
Warning symbols - explanation
The column Order number and explanation provides an explanation
of the neighbouring warning symbol. The description of the warning
symbols is always the same and specifies, in the following order:
1. A description of the danger.
For example: danger of cutting!
2. The consequence of non-compliance with risk avoidance instruc-
tions.
For example: causes serious injuries to fingers or hands.
3. Instructions for avoiding the danger.
For example: only touch machine parts when they have come to
a complete standstill.

General safety instructions
16
ZG-TS BAG0168.1 08.17
2.13.1 Positions of warning symbols and other labels
The following diagrams show the arrangement of the warning symbols
on the machine.
F
ig. 1
Fig
. 2

General safety instructions
ZG-TS BAG0168.1 08.17
17
Order number and explanation
Warning symbols
MD 075
Risk of fingers and hands being cut or cut off
by accessible, moving parts involved in the
work process.
This danger can cause extremely serious injuries
and the loss of body parts.
•Never reach into the danger area when the
tractor engine is running with PTO shaft /
hydraulic / electronics system connected.
•Wait for all moving machine parts to come
to a complete standstill before reaching into
the danger area.
MD 078
Risk of contusions for fingers or hands
through accessible moving machine parts!
In these cases there is a danger of extremely
serious injuries leading to the loss of body parts
such as fingers or hands.
Never reach into the danger area when the trac-
tor engine is
running with cardan shaft / hydraulic
system connected.
MD 082
Risk of falling for personnel riding on treads
or platforms.
This danger can cause extremely serious and
potentially fatal injuries.
It is forbidden to ride on the machine or climb the
machine when it is running. This also applies to
machines with treads or platforms.
Make sure that nobody is riding on the machine.
MD 088
Risk of being drawn in or caught by moving
parts involved in the work process, caused
by climbing on the loading pl
atform when the
machine is running.
This danger can cause extremely serious and
potentially fatal injuries.
Never climb onto the loading platform when the
tractor engine is running with PTO shaft / hydrau-
lic / electronics system connected.

General safety instructions
18
ZG-TS BAG0168.1 08.17
MD 095
Read and follow the operating manual and safety
information before starting up the machine!
MD 096
Danger from escaping high-pressure hydrau-
lic fluid due to leaking hydraulic hose lines.
This danger may cause serious injuries, perhaps
even resulting in death, if escaping high-
pressure
hydraulic fluid passes through the skin and into
the body.
•Never attempt to plug leaks in hydraulic
hose lines using your hand or fingers.
•Read and observe the information in the
operating manual before carrying out
maintenance and repair work on the hy-
draulic hose lines.
•If you are injured by hydraulic fluid, contact
a doctor immediately.
MD 098
Danger from flying fertiliser particles.
Please ensure that all personnel maintain a suffi-
cient safety distance and stay outside the danger
area.
MD 100
This symbol indicates anchorage points for fas-
tening slinging gear when loading the machine.

General safety instructions
ZG-TS BAG0168.1 08.17
19
MD 102
Danger from intervention in the machine, e.g.
installation, adjusting, troubleshooting,
cleaning, maintaining and repairing, due to
the tractor and the machine being started
unintentionally and rolling.
These dangers can cause extremely serious and
potentially fatal injuries.
•Secure the tractor and the machine against
unintentional start-up and rolling before any
intervention in the machine.
•Depending on the type of intervention, read
and understand the information in the rele-
vant sections of the operating manual.
MD 114
This symbol indicates a lubrication point.
MD 153
This pictogram indicates a hydraulic oil filter
MD 199
The maximum operating pressure of the hydrau-
lic system is 210 bars.

General safety instructions
20
ZG-TS BAG0168.1 08.17
2.14 Dangers if the safety information is not observed
Non-compliance with the safety information
•Can pose both a danger to people and also to the environment
and machine.
•Can lead to the loss of all warranty claims.
Seen individually, non-compliance with the safety information could
pose the following risks:
•Danger to people through non-secured working areas.
•Failure of important machine functions.
•Failure of prescribed methods of maintenance and repair.
•Danger to people through mechanical and chemical impacts.
•Risk to environment through leakage of hydraulic fluid.
2.15 Safety-conscious working
Besides the safety information in this operating manual, the national
general workplace safety and accident prevention regulations are
binding.
Comply with the accident prevention instructions on the warning sym-
bols.
When driving on public roads and routes, comply with the appropriate
statutory road traffic regulations.