Amazone Groundkeeper SmartCut GH 1350 User manual

Operating manual
AMAZONE
GROUNDKEEPER
SmartCut
GH 1350
GH 1500
GH 1800
HorseHopper
SmartCut
HH 1500
HH 1800
MG5069
BAF0005.4 06.21
Printed in France
Read and observe this operat-
ing manual before putting the
equipment into operation for
the first time!
Keep in a safe place for future
reference!
en

2
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
READING THE INSTRUCTION
manual and adhering to it should not appear to
be inconvenient and superfluous as it is not
enough to hear from others and to realise that a
machine is good, to buy it and to believe that
now everything should work by itself. The person
concerned would not only harm himself but also
make the mistake of blaming the machine for the
reason of a possible failure instead of himself. In
order to ensure good success one should go into
the mind of a thing, make himself familiar with
every part of the machine and to get acquainted
with its handling. Only in this way would you be
satisfied both with the machine as also with
yourself. To achieve this is the purpose of this in-
struction manual.
Leipzig-Plagwitz 1872.

Foreword
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
3
Identification data
Enter the identification data for the machine here. You can find the
identification data on the rating plate.
Machine identification number:
(ten-digit)
Type:
Groundkeeper GH / HH
SMARTCUT
Year of manufacture:
Basic weight (kg):
Approved total weight (kg):
Maximum load (kg):
Manufacturer's address
AMAZONE S.A. FORBACH
17, rue de la Verrerie
BP 90106
F-57602
Phone:
Fax:
E-mail:
Forbach, France
[phone]
[phone]
[e-mail]
Spare part orders
Spare parts lists are freely accessible in the spare parts portal at
www.amazone.de.
Please send orders to your AMAZONE dealer.
Formalities of the operating manual
Document number:
MG5069
Compilation date:
06.21
ã Copyright AMAZONEN-WERKE H. DREYER SE & Co. KG, 2021
All rights reserved.
Reprinting, even of sections, permitted only with the approval of
AMAZONEN-WERKE H. DREYER GmbH & Co. KG.

Foreword
4
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
Foreword
Dear Customer,
You have chosen a quality product from the comprehensive range of
products supplied by AMAZONEN-WERKE, H. DREYER SE & Co.
KG. Thank you for placing your trust in our brand.
When the machine arrives, please make sure that no damage has
occurred in transit and that no parts are missing! Check the machine
for completeness including the special optional equipment ordered
against the delivery note. Replacements will only be made for claims
made immediately!
Read this operating manual before putting the equipment into opera-
tion for the first time, paying particular attention to the safety instruc-
tions. By reading the manual carefully you will be able to fully exploit
the potential of your newly acquired machine.
Please ensure that all the machine operators have read this operating
manual before they put the machine into operation.
Should you have any questions or problems, please consult this op-
erating manual or contact your local service partner.
Regular maintenance and timely replacement of worn or damaged
parts increases the lifespan of your machine.
User evaluation
Dear Reader
Our operating manual is updated regularly. Your suggestions for im-
provements will help us always to present the operating manual in a
more user-friendly form. Please send your suggestions to:
AMAZONE S.A. FORBACH
17, rue de la Verrerie
BP 90106
F-57602
Phone:
Fax:
E-mail:
Forbach, France
[phone]
[phone]
[e-mail]

Foreword
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
5
1 User information .......................................................................................... 7
1.1 Purpose of the document ........................................................................................................ 7
1.2 Locations in the operating manual .......................................................................................... 7
1.3 Diagrams used ........................................................................................................................ 7
2 General safety instructions ......................................................................... 8
2.1 Obligations and liability ........................................................................................................... 8
2.2 Representation of safety symbols ......................................................................................... 10
2.3 Organisational measures ...................................................................................................... 11
2.4 Safety and protection equipment .......................................................................................... 11
2.5 Informal safety measures ...................................................................................................... 11
2.6 User training .......................................................................................................................... 12
2.7 Safety measures in normal operation ................................................................................... 13
2.8 Dangers from residual energy ............................................................................................... 13
2.9 Maintenance and repair work, fault elimination ..................................................................... 13
2.10 Constructive changes ........................................................................................................... 13
2.10.1 Spare and wear parts and aids ............................................................................................. 14
2.11 Cleaning and disposal ........................................................................................................... 14
2.12 User workstation ................................................................................................................... 14
2.13 Warning symbols and other signs on the machine ............................................................... 15
2.13.1 Positioning of warning symbols and other labels .................................................................. 21
2.14 Dangers if the safety information is not observed ................................................................. 22
2.15 Safety-conscious working ..................................................................................................... 22
2.16 Safety information for users .................................................................................................. 23
2.16.1 General safety and accident prevention information ............................................................ 23
2.16.2 Hydraulic system ................................................................................................................... 26
2.16.3 Electrical system ................................................................................................................... 27
3 General description of the machine ......................................................... 28
3.1 Areas of application .............................................................................................................. 28
3.2 Declaration of conformity ...................................................................................................... 28
3.3 Details required for enquiries ................................................................................................ 28
3.4 Identification of the machine ................................................................................................. 28
3.5 Technical data ....................................................................................................................... 29
3.5.1 Noise production data ........................................................................................................... 29
3.6 Intended use ......................................................................................................................... 30
4 Taking delivery of the machine ................................................................ 30
5 Attaching and removing the machine at the tractor's rear three-point
system ......................................................................................................... 31
5.1 PTO shaft .............................................................................................................................. 34
5.2 Fitting and adjusting the PTO shaft ....................................................................................... 35
5.2.1 Fitting the PTO shaft ............................................................................................................. 35
5.2.2 Adjusting the PTO shaft when first attached ......................................................................... 35
5.3 Groundkeeper / HorseHopper transmission input speed ...................................................... 36
5.4 Hydraulic connections ........................................................................................................... 37
5.4.1 Coupling hydraulic hose lines ............................................................................................... 38
5.4.2 Disconnecting hydraulic hose lines ....................................................................................... 38
6 The mower unit .......................................................................................... 39
6.1 Fitting the mowing and scarifying tools ................................................................................. 39
6.2 Mowing .................................................................................................................................. 45
6.3 Scarifying .............................................................................................................................. 46

Foreword
6
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
6.4 Mulching ................................................................................................................................ 48
6.5 Collecting .............................................................................................................................. 49
6.6 Emptying the hopper ............................................................................................................. 50
7 Adjusting the cutting height ...................................................................... 52
7.1 Front roller (option) ................................................................................................................ 54
8 Cleaning the machine ................................................................................ 55
9 Maintenance are care ................................................................................. 57
9.1 Oil level in the angular gearbox ............................................................................................ 57
9.2 Lubrication points .................................................................................................................. 57
9.3 Extended periods of downtime .............................................................................................. 59
9.4 Tyre pressure ........................................................................................................................ 59

User information
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
7
1 User information
The "User information" section supplies information on using the op-
erating manual.
1.1 Purpose of the document
This operating manual
• Describes the operation and maintenance of the machine.
• Provides important information on safe and efficient handling of
the machine.
• Is a component part of the machine and should always be kept
with the machine or the traction vehicle.
• Keep it in a safe place for future use.
1.2 Locations in the operating manual
All the directions specified in the operating manual are always viewed
in the direction of travel.
1.3 Diagrams used
Instructions for action and reactions
Tasks to be carried out by the owner/operator appear in the form of
numbered handling instructions. Observe the sequence of the han-
dling instructions given. The result of the relevant handling instruction
is indicated by an arrow as necessary.
Example:
1. Instruction for action 1
→ Reaction of the machine to instruction for action 1
2. Instruction for action 2
Lists
Lists without a mandatory sequence a presented as a list with bullet
points.
Example:
• Point 1
• Point 2
Item numbers in diagrams
Digits shown in round brackets refer to the position number in the
illustration. The first digit refers to the illustration, the second refers to
the position number in the illustration. Example: (Fig. 3/6)
• Figure 3
• Item 6

General safety instructions
8
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
2 General safety instructions
This section contains important information on safe operation of the
machine.
2.1 Obligations and liability
Comply with the instructions in the operating manual
Knowledge of the basic safety information and safety regulations is a
basic requirement for safe handling and fault-free machine operation.
Obligations of the operator
The operator is obliged only to let those people work with/on the ma-
chine who
• Are aware of the basic workplace safety information and acci-
dent prevention regulations.
• Have been trained in working with/on the machine.
• Have read and understood this operating manual.
The operator is obliged
• To keep all the warning symbols on the machine in a legible
state.
• To replace damaged warning symbols.
If you still have queries, please contact the manufacturer.
Obligations of the user
Before starting work, anyone charged with working with/on the ma-
chine is obliged
• To comply with the basic workplace safety instructions and acci-
dent prevention regulations.
• To read and understand the section "General safety information"
of this operating manual.
• To read the section "Warning symbols and other labels on the
machine" of this operating manual and to follow the safety in-
structions represented by the warning symbols when operating
the machine.
• To get to know the machine.
• To read the sections of this operating manual, important for car-
rying out your work.
If it comes to the attention of the user that the safety features of the
equipment are not in working order, the user must rectify this immedi-
ately. If this is not a task that is normally carried out by the user or if
the user has insufficient technical knowledge to do so, the user must
notify his superior (owner/operator) about the defect.

General safety instructions
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
9
Risks in handling the machine
Although the machine is built using state-of-the-art technology accord-
ing to standard safety regulations, this does not rule out the possibility
of danger and impaired operation when the machine is in use
• For the health and safety of the user or third persons,
• For the machine,
• For other goods.
Only use the machine
• For the purpose for which it was intended.
• In a perfect state of repair.
Eliminate any faults that could impair safety immediately.
Guarantee and liability
Our "General terms and conditions of sale and delivery" generally
apply. These are available to the owner/operator upon conclusion of
the contract at the latest. Warranty and liability claims in the event of
injury to persons and material damage will be excluded if they are
based on one or several of the following causes:
• Improper use of the machine.
• Improper installation, start-up, operation and maintenance of the
machine.
• Operation of the machine with defective safety equipment or
improperly attached or non-functioning safety equipment.
• Non-compliance with the instructions in the operating manual
regarding commissioning, operation and maintenance.
• Independently-executed construction changes to the machine.
• Insufficient monitoring of machine parts that are subject to wear.
• Improperly executed repairs.
• Catastrophic events as a result of the impact of foreign objects
or force majeure.

General safety instructions
10
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
2.2 Representation of safety symbols
Safety instructions are indicated by the triangular safety symbol pre-
ceded by a signal word. The words (DANGER, WARNING, CAU-
TION) describe the severity of the danger present and have the fol-
lowing significance:
DANGER
Indicates an immediate high risk, which will result in death or
extremely serious physical injury (loss of body parts or long
term damage) if not avoided.
If the instructions are not followed, then this will result in imme-
diate death or serious physical injury.
WARNING
Indicates a medium risk, which could result in death or (extreme-
ly serious) physical injury if not avoided.
If the instructions are not followed, then this may result in death
or serious physical injury.
CAUTION
Indicates a low risk, which could incur minor or medium level
physical injury or damage to property if not avoided.
IMPORTANT
Indicates an obligation to special behaviour or an activity re-
quired for proper machine handling.
Non-compliance with these instructions can cause faults on the
machine or in the environment.
NOTE
Indicates handling tips and particularly useful information.
These instructions will help you to use all the functions of your
machine to the optimum.

General safety instructions
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
11
2.3 Organisational measures
The operator must provide the necessary personal protective equip-
ment, such as:
• Protective glasses
• Protective shoes
• Protective suit
• Skin protection, etc.
The operation manual
• Must always be kept at the place at which the machine is oper-
ated.
• Must always be easily accessible for the user and maintenance
personnel.
Check all the available safety equipment regularly.
2.4 Safety and protection equipment
All safety and protective equipment must be properly installed and
functional each time the machine is put into operation. Check all safe-
ty and protective equipment regularly.
Faulty safety equipment
Faulty or disassembled safety and protection equipment can lead to
dangerous situations.
2.5 Informal safety measures
As well as all the safety information in this operating manual, comply
with the general, national regulations pertaining to accident prevention
and environmental protection.
When driving on public roads and routes, then you should comply with
the statutory road traffic regulations.

General safety instructions
12
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
2.6 User training
Only persons who have received appropriate training and instruction
may work on or with the machine. The owner/operator must clearly
define the responsibilities of those in charge of the operation, mainte-
nance and repair of the machine.
People being trained may only work with/on the machine under the
supervision of an experienced person.
People
Activity
Person special-
ly trained for the
activity 1)
Trained person
2)
Person with specialist
training (specialist work-
shop) 3)
Loading/Transport
X
X
X
Commissioning
--
X
--
Set-up, tool installation
--
--
X
Operation
--
X
--
Maintenance
--
--
X
Troubleshooting and fault elimina-
tion
--
X
X
Disposal
X
--
--
Legend:
X..permitted
--..not permitted
1) A person who can assume a specific task and who can carry out
this task for an appropriately qualified company.
2) Instructed persons are those who have been instructed in their
assigned tasks and in the possible risks in the case of improper
behaviour, have been trained if necessary, and have been in-
formed about the necessary protective equipment and
measures.
3) A specialist is a person who has received specific technical
training (i.e. an expert) and has knowledge of the appropriate
regulations, and can therefore properly assess the work entrust-
ed to him and identify the dangers associated with this work.
Comment:
A qualification equivalent to specialist training can be obtained
through long term activity in the appropriate field of work.
Only a specialist workshop may carry out maintenance and repair
work on the machine when such work is specifically designated
"workshop work". The personnel in a specialist workshop have the
requisite knowledge and suitable equipment (tools, lifting and support
devices) to carry out the maintenance and repair work on the ma-
chine properly and safely.

General safety instructions
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
13
2.7 Safety measures in normal operation
Only operate the machine if all the safety and protection equipment is
fully functional.
Check the machine at least once a day for visible damage and check
the function of the safety and protection equipment.
2.8 Dangers from residual energy
Note that there may be residual mechanical, hydraulic, pneumatic and
electrical/electronic energy at the machine.
Take appropriate measures when instructing the operating personnel.
Detailed information is provided again in the various chapters of this
operating manual.
2.9 Maintenance and repair work, fault elimination
Carry out prescribed setting, maintenance and inspection work in a
timely manner.
Secure all media such as compressed air and the hydraulic system
against unintentional start-up.
Carefully fix and secure larger subassemblies to lifting gear when
carrying out replacement work.
Regularly check that bolted connections are firmly secured and tight-
en if necessary.
When the maintenance work is completed, check the function of the
safety devices
2.10 Constructive changes
You must not modify, add to or convert the machine without the con-
sent of AMAZONE. This also applies to welding work on load-bearing
parts.
Any addition or conversion measures require the written consent of
AMAZONE. Use only modification and accessory parts approved by
AMAZONE – this ensures (for example) that the operating permit
remains valid in accordance with national and international regula-
tions.
Vehicles with an official type approval or with equipment connected to
a vehicle with a valid type approval or approval for road transport
according to the German road traffic regulations must be in the state
specified by the approval.

General safety instructions
14
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
WARNING
Risk of being crushed, cut, caught, drawn in or struck if support-
ing parts break.
It is forbidden to:
• Drill holes in the frame or on the chassis.
• Increasing the size of existing holes on the frame or the chassis.
• Welding support parts.
2.10.1 Spare and wear parts and aids
Immediately replace any machine parts which are not in a perfect
state.
Only use genuine spare and wear parts or parts
approved by AMAZONE. This ensures that the operating permit re-
mains valid in accordance with national and international regulations.
Where spare and wear parts of other makes are used, it cannot be
guaranteed that they are appropriately designed and manufactured
for the corresponding loading and safety requirements.
AMAZONE accepts no liability for damage arising from the use of
unapproved spare parts, wear parts or auxiliary materials.
2.11 Cleaning and disposal
Handle and dispose of any materials used carefully, in particular:
• When carrying out work on lubrication systems and equipment
and
• When cleaning using solvents.
2.12 User workstation
The machine may be operated by only one person sitting in the driv-
er's seat of the tractor.

General safety instructions
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
15
2.13 Warning symbols and other signs on the machine
Always ensure that all warning symbols on the machine are clean and
clearly legible! Renew unreadable warning symbols. Warning symbols
can be obtained via your dealer by quoting the order number (e.g. MD
075).
Warning symbols - structure
Warning symbols identify danger areas on the machine and warn
against residual dangers. A permanent or unexpectedly occurring
danger exists at these points.
A warning symbol consists of two fields:
Field 1
is a symbol describing the danger, surrounded by triangular safety
symbol.
Field 2
is a symbol showing how to avoid the danger.
Warning symbols - explanation
A description of the warning symbol is given in the order number and
explanation column next to it. The description of the warning symbol
always has the same structure with the information being provided in
the following order:
1. A description of the danger.
For example: danger of cutting!
2. The consequence of non observance of the danger protection
instructions.
For example: causes serious injuries to fingers or hands.
3. Instructions for avoiding the danger.
For example: only touch machine parts when they have come to
a complete standstill.

General safety instructions
16
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
Order number and explanation
Warning symbols
MD 075
Risk of fingers and hands being cut or sev-
ered by rotating machine parts.
This hazard can cause extremely serious injuries
with the loss of body parts such as fingers or
hands.
Never reach into the danger area when the trac-
tor engine is running with the PTO
shaft/hydraulic system connected.
Do not touch machine parts until they have come
to a complete standstill.
MD 076
Risk of hands or arms being drawn in or
caught by power-driven, unprotected chain
or belt drives.
This hazard can cause extremely serious inju-
ries, including loss of parts of the body from
hands or arms.
Never open or remove protective equipment
from chains or belt drives,
• while the tractor engine is running and the
PTO shaft is connected/hydraulic drive is
engaged
• or the ground wheel drive is in motion
MD 078
Risk of fingers or hands being crushed by
accessible moving machine parts.
This hazard can cause extremely serious injuries
with the loss of body parts such as fingers or
hands.
Never reach into the danger area when the trac-
tor engine is running with the PTO
shaft/hydraulic system connected.

General safety instructions
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
17
MD 079
Hazard from materials or foreign objects that
are thrown from or ejected by the machine.
This hazard can cause extremely serious injuries
to any part of the body.
Ensure that persons not involved in the operation
of the machine maintain a sufficient safety dis-
tance from the danger area created by the ma-
chine while the tractor engine is running.
MD 080
Danger of crushing of torso in articulated
area of drawbar due to sudden steering
movements!
This can inflict extremely serious injuries to the
torso which may also be fatal.
Persons must not enter or remain in the danger
zone between the tractor and machine if the
tractor engine is running and the tractor is not
secured to prevent it from accidentally rolling
away.
MD 087
Risk of toes or feet being cut or severed by
power-driven tools.
This hazard can cause serious injuries, including
loss of parts of the body from toes or feet.
Maintain a sufficient safety distance from the
danger area while the tractor engine is running
and the PTO shaft/hydraulic system is connect-
ed.
MD 090
Risk of contusions from unintentional rolling
of the uncoupled, unsecured machine!
This hazard can cause extremely serious injuries
anywhere on the body, or even death.
Secure the machine to prevent it from accidental-
ly rolling away before uncoupling it from the trac-
tor using the parking brake and/or wheel
chock(s).

General safety instructions
18
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
MD 095
Read and understand the operating manual safe-
ty information before starting up the machine!
MD 096
Danger of infection to the whole body from
liquids escaping at a high pressure (hydraulic
fluid)!
This danger will cause serious injuries over the
whole body, if hydraulic fluid escaping at high
pressure passes through the skin and into the
body.
Never attempt to plug leaks in hydraulic lines
using your hand or fingers.
Read and understand the information in the op-
erating manual before carrying out maintenance
and repair work.
If you are injured by hydraulic fluid, contact a
doctor immediately.
MD 097
Risk of any part of the body being crushed
due to standing in the stroke area of the
three-point suspension when the three-point
hydraulics are operated.
This hazard can cause extremely serious and
potentially fatal injuries.
• Personnel are prohibited from standing in
the stroke area of the three-point suspen-
sion when the three-point hydraulics are
operated.
• Actuate the operating controls for the trac-
tor's three-point hydraulic system
o only from the designated workstation,
o never from a location in the stroke ar-
ea between tractor and machine.

General safety instructions
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
19
MD 100
This symbol indicates lashing points for fastening
slinging gear when loading the machine.
MD 102
Danger during intervention in the machine,
e.g. installation, adjusting, troubleshooting,
cleaning, maintaining and repairing, due to
the tractor and the machine being started
unintentionally and rolling.
These dangers can cause extremely serious and
potentially fatal injuries.
• Secure the tractor and the machine against
unintentional start-up and rolling before any
intervention in the machine.
•
Read and observe the information in the
relevant chapter for the type of interven-
tion
MD 113
Study and observe the instructions for cleaning,
servicing and maintaining in the appropriate
chapter of the operating manual.
MD 114
This symbol indicates a lubrication point

General safety instructions
20
Groundkeeper GH / HH SMARTCUT BAF0005.4 06.21
MD 118
This symbol indicates the maximum drive speed
(540 rpm) and direction of rotation of the drive
shaft on the machine side.
MD 170
Risk of being crushed, drawn in or caught by
unprotected, moving machine parts as a re-
sult of missing safety devices.
This hazard can cause extremely serious inju-
ries, including the loss of body parts.
Close protective equipment which has been
opened or refit protective equipment which has
been removed before you start the machine.
MD 199
The maximum operating pressure of the hydrau-
lic system is 210 bar.