ARM ARM710T User manual

ARM DUI 0114A
ARM710T Header Card
(KPI-0032A)
User Guide

ii © Copyright ARM Limited 1999. All rights reserved. ARM DUI 0114A
ARM710T Header Card
User Guide
© Copyright ARM Limited 1999. All rights reserved.
Release information
Proprietary notice
ARM, the ARM Powered logo, Thumb and StrongARM are registered trademarks of ARM Limited.
The ARM logo, AMBA, PrimeCell, Angel, ARMulator, EmbeddedICE, ModelGen, Multi-ICE,
ARM7TDMI, ARM7TDMI-S, ARM9TDMI, TDMI and STRONG are trademarks of ARM Limited.
Document confidentiality status
This document is Open Access. This document has no restriction on distribution.
Product status
The information in this document is Final (information on a developed product).
ARM web address
http://www.arm.com
Change history
Date Issue Change
27th April 1999 A Release
A
ll
ot
h
er pro
d
ucts or serv
i
ces ment
i
one
d
h
ere
i
n may
b
e tra
d
emar
k
s o
f
t
h
e
i
r respect
i
ve owners.
Neither the whole nor any part of the information contained in, or the product described in, this document may
be adapted or reproduced in any material form except with the prior written permission of the copyright
holder.
The product described in this document is subject to continuous developments and improvements. All
particulars of the product and its use contained in this document are given by ARM Limited in good faith.
However, all warranties implied or expressed, including but not limited to implied warranties or
merchantability, or fitness for purpose, are excluded.
This document is intended only to assist the reader in the use of the product. ARM Limited shall not be liable
for any loss or damage arising from the use of any information in this document, or any error or omission in
such information, or any incorrect use of the product.

ARM DUI 0114A © Copyright ARM Limited 1999. All rights reserved. iii
Preface
This preface introduces the ARM710T Header Card and its reference documentation. It
contains the following sections:
•About this document on page iv
•Further reading on page vi
•Feedback on page vii.

iv © Copyright ARM Limited 1999. All rights reserved. ARM DUI 0114A
About this document
This document is the ARM710T Header Card User Guide.
Intended audience
This document has been written for experienced hardware and software engineers who
wish to use an ARM710T header card, with their ARM development board, for code
development and evaluation.
Organization
This document is organized into the following chapters:
Chapter 1 Overview of the ARM710T Header Card
Read this chapter for an introduction to the ARM710T Header Card.
Chapter 2 Setting up your System
Read this chapter for a description of how to set up the ARM
development board to work with the ARM710T Header Card.
Chapter 3 Configuring the ARM710T Header Card
Read this chapter for a description of how to configure the ARM710T
Header Card.
Chapter 4 Circuit Descriptions
Read this chapter for a description of the circuit board of the
ARM710T Header Card.
Typographical conventions
The following typographical conventions are used in this document:
bold HighlightsARMprocessorsignalnameswithintext,andinterface
elements such as menu names. May also be used for emphasis in
descriptive lists where appropriate.
italic Highlights special terminology, cross-references and citations.
typewriter Denotes text that may be entered at the keyboard, such as
commands, file names and program names, and source code.

ARM DUI 0114A © Copyright ARM Limited 1999. All rights reserved. v
typewriter Denotes a permitted abbreviation for a command or option. The
underlined text may be entered instead of the full command or
option name.
typewriter italic
Denotesargumentsto commandsor functionswherethe argument
is to be replaced by a specific value.
typewriter bold Denotes language keywords when used outside example code.

vi © Copyright ARM Limited 1999. All rights reserved. ARM DUI 0114A
Further reading
This section lists publications by ARM Limited.
ARM publications
For additional information, refer to the following:
•ARM Target Development System User Guide (ARM DUI 0061).
•ARM Multi-ICE User Guide (ARM DUI 0048).
•ARM Multi-ICE Installation Guide (ARM DSI 0005).
•ARM Software Development Toolkit User Guide (ARM DUI 0040).
•ARM710T Datasheet (ARM DDI 0086).

ARM DUI 0114A © Copyright ARM Limited 1999. All rights reserved. vii
Feedback
ARM Limited welcomes feedback both on the ARM710T header card, and on the
documentation.
Feedback on this document
If you have any comments on this document, please send email to [email protected]
giving:
• the document title
• the document number
• the page number(s) to which your comments refer
• a concise explanation of your comments.
General suggestions for additions and improvements are also welcome.
Feedback on the ARM710T header card
If you have any comments or suggestions about this product, please contact your
supplier giving:
• the product name
• a concise explanation of your comments.

viii © Copyright ARM Limited 1999. All rights reserved. ARM DUI 0114A

ARM DUI 0114A © Copyright ARM Limited 1999. All rights reserved. ix
Contents
ARM710T Header Card User Guide
Preface
About this document ......................................................................................................iv
Further reading...............................................................................................................vi
Feedback ......................................................................................................................vii
Chapter 1 Overview of the ARM710T Header Card
1.1 Introduction to the ARM710T header card....................................................1-2
1.2 Board layout..................................................................................................1-3
Chapter 2 Setting up your System
2.1 Setting up your ARM development board.....................................................2-2
2.2 Debugging using Angel.................................................................................2-4
2.3 Debugging using Multi-ICE...........................................................................2-5
2.4 Debugging using EmbeddedICE...................................................................2-6
Chapter 3 Configuring the ARM710T Header Card
3.1 Setting the core clock frequency...................................................................3-2
3.2 Surface mount links ......................................................................................3-4
3.3 Using the external clock input.......................................................................3-5
3.4 Setting the bus clocking mode......................................................................3-6
3.5 Setting the endianness .................................................................................3-7

x © Copyright ARM Limited 1999. All rights reserved. ARM DUI 0114A
Chapter 4 Circuit Descriptions
4.1 The header card circuit board....................................................................... 4-2
4.2 Connectors ................................................................................................... 4-4
Index