Assa Abloy Aperio User manual

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
[email protected]
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Install Guide
Assa Abloy Aperio

Document
Document Details
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
[email protected]
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
V1.0 (20211008)
(V1.0 first published 20230523)
Firmware
Firmware version can be verified on
Verkada Command command.verkada.com.
2

Introduction
Introduction
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
[email protected]
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
3
Assa Abloy Aperio Integration into Verkada System.
For all Assa Abloy documentation including lock
installation and datasheets, sign into Assa’s content
portal.
Background
Assa Abloy’s Aperio technology is a cross brand wireless communication protocol centered
around their AH series hub. Please contact your Assa Abloy representative to find out which
wireless lock under the Aperio umbrella works for your use case.
Verkada specifically integrates with the AH30 hub which communicates with the AC41/AC42 via the
RS-485 module in the AUX cassette/terminal block. In order for an AC41/AC42 to be utilized for the
Assa Integration, it must be set to Assa mode. This is done during the commissioning process.
While in Assa Abloy mode, the AC41/AC42 cannot control traditional wired doors. The AC41/AC42
can control up to 16 wireless locks.
Integration Process
The integration process should be split into two phases.
1. Assa Installation and Configuration.
a. Installation of locks.
b. Wiring AH30 into Verkada Aux for power.
c. Linking of hubs and locks.
2. Verkada Command Setup
a. Claim controller and set as Assa mode
b. Add doors with lock’s EAC address
Phase one of the integration is totally independent to Verkada, besides using the
controllers RS-485 to power the AH30.

Introduction
Common use cases
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
[email protected]
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
4
Many schools, universities, medical facilities and multi-tenant units use wireless locks to secure
doors that are operated with low frequency
Schools/Campuses
Classroom doors, Offices, Break rooms
Universities/Medical Facilities
Dorm Rooms, Lecture Halls, Offices, Laboratories
In multi-tenant
Officeses, Supply closets
These verticals use wireless locks because they do not require expensive wiring to be run
through walls and allow much more flexibility. They are also much more cost effective than
wired doors. This integration allows us to work with existing customers with Aperio enabled
wireless locks.
Important notes
Tips to help you do your best:
●Read all of the Assa Abloy documentation for the lock series being installed.
●Verkada support will NOT troubleshoot or Assa Abloy hardware!
●Wireless locks are wireless products so wireless range is always a concern, please
ensure that the AH30 is placed within range of all the connected locks.

Installation
Installation Order of Operation
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
[email protected]
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
5
1. Install and configure the AH30
2. Install and configure the wireless lock
3. Configure the AC41/AC42
Wiring AH30 to the AC41/AC42
This step is done first simply to provide power to the AH30. No Command configuration is
required until after the locks and hub are successfully connected.
Post Aperio Lock setup
Once you have successfully linked your locks to your hub, you will need to write down all the
EAC addresses. These will be used when adding the locks as doors in Command.
AUX
RS-485
AH30
+↔8-24VDC
- ↔ GND
A↔A
B↔B

Installation
Command Configuration
1. Add the AC41/42 to Command
and select Assa Abloy
2. Once the AC41/AC42 is added
and in Assa Abloy mode,
navigate to the controller and
click add door. The window to the
right will pop up. Select the type
of lock and the EAC
address(which you will get from
the Aperio setup)

Installation
Command Configuration Cont.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
[email protected]
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
7
A successful connection will result in on “online” status for the lock.
The settings page of the AC41/AC42 will also signal the health of the connection.

Installation
Wiring
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
[email protected]
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
8
AH30 Wiring
AUX
RS-485
AH30
+↔8-24VDC
-↔GND
A↔A
B↔B
Troubleshooting Guidelines
1. Verify that your ACU is in schlage mode - if you forgot to set it to Assa Abloy mode, you
will need to decommission it and re-add it.
2. Verify that the Assa Abloy Locks and AH30ss have been successfully paired
3. Ensure that the addresses for each Assa Abloy lock were successfully configured.
Additionally, ensure that the addresses provided when setting up the door in command
are correct.

Appendix
Support
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
[email protected]
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Thank you for purchasing this Verkada product. If for any reason
things don’t work right, or you need assistance, please contact us
immediately.
verkada.com/support
Sincerely, The Verkada Team
9