Assa Abloy Corbin Russwin HP3000 Series User manual

In U.S.: In Canada:
Corbin Russwin, Inc. ASSA ABLOY Door Security Solutions Canada
225 Episcopal Road 160 Four Valley Drive
Berlin, CT 06037 USA Vaughan, Ontario, Canada L4K 4T9
Phone: [phone] Phone: [phone]
Technical Product Support: Phone: [phone]
Installation Instructions
HP3000 Series Tubular Lock
With Push/Pull Paddle Trim
FM 333 10/18
Copyright © 2011, Corbin Russwin, Inc., an ASSA ABLOY Group Company.
All rights reserved. Reproduction in whole or in part without the express
written
p
ermission of Corbin Russwin, Inc. is
p
rohibited.
Item No. Description Qty.
1 Axle, Paddle Trim 2
2 Paddle (Plain) 2
3 Cover, Passage Paddle Trim 2
4 Actuator, Paddle Insert Cam 2
5 Post, Mounting 2
6 Chassis, Paddle Trim 2
7 Spacer, Alignment 2
8 Front, Latch 1
9 Latch 1
10 Plate, Insert 1
11 Screw, Chassis Mounting, #8-32x5/8 SEMS 2
** Screw, Cover Mounting, #8-32x5/16 OH 4
** Screw, Actuator Mtg, #8-32x5/16 4
** Screw, Alignment, #8-32x1/2 PH (self tap) 4
** Screw, Alignment, #8-32x9/16 PH 4
** Parts are not shown in diagram above
Tools Required
#2 Phillips Screwdriver
Drill
7/64 Drill Bit (wood door)
#8-32 Tap (metal door)
#18 (.136) Tap Drill
ASSA ABLOY, the global leader in door opening solutions
WARNING
This product can expose
you to lead which is
known to the state of
California to cause cancer
and birth defects or other
reproductive harm. For
more information go to
www.P65warnings.ca.gov.
08/2018

STEP 1: Latch Installation
Position plate insert in 2-1/8” bore
Insert latch through 1” bore
For privacy function make sure threaded
piece on latch is towards the inside of
the door
Snap latch into plate insert
Install (2) #8 combination screws to
secure latch
Do not fully tighten
STEP 2: Determine Orientation of Trim
Remove the chassis which is packed with the paddle and cover
Passage trim can be mounted vertically or horizontally
Privacy trim can only be mounted vertically
Position chassis and verify the spindle engages into the latch hubs
Cams on chassis must be oriented as shown (vertical orientation for vertical
mounting and horizontal orientation for horizontal mounting)
Vertical
Horizontal
Cams must be oriented as shown
ASSA ABLOY, the global leader in door opening solutions
Copyright © 2011, Corbin Russwin, Inc., an ASSA ABLOY Group Company.
All rights reserved. Reproduction in whole or in part without the express
written permission of Corbin Russwin, Inc. is prohibited.

STEP 3: Chassis Installation
Install an alignment spacer on to each chassis (one
oriented up, one oriented down to match plate insert
in bore)
Insert (2) mounting posts through the chassis on the
outside of the door
Install (2) #8-32x5/8 machine screws with integrated
lock washer through the chassis on the inside of the
door to secure
Make sure the chassis’ are square to the door and
fully tighten screws
Fully tighten latch screws
Install surface mounted screws to secure alignment
-For wood doors: 7/64” pilot hole
-For metal doors: drill and tap for #8-32 screw
Check operation by turning cams by hand. If binding
occurs loosen chassis mounting screws and
retighten
For privacy function install push button on inside of
door
If trim is mounted VERTICAL and the end of the paddle will
point towards the HINGE, attach the insert to the paddle in
the orientation shown:
The paddle has three potential orientations:
-VERTICAL
-HORIZONTAL – UP
-HORIZONTAL – DOWN
The insert is attached to the paddle using
(2) #8-32 x 5/16” Machine Screws (VC-3
Coated)
STEP 4: Determine Orientation of Paddle
If trim is mounted HORIZONTAL and the end of the
paddle will point UP, attach the insert to the paddle in
the orientation shown (same as vertical):
If trim is mounted HORIZONTAL and the end of the
paddle will point DOWN, attach the insert to the paddle in
the orientation shown:
Copyright © 2011, Corbin Russwin, Inc., an ASSA ABLOY Group Company.
All rights reserved. Reproduction in whole or in part without the express
written
p
ermission of Corbin Russwin, Inc. is
p
rohibited.
ASSA ABLOY, the global leader in door opening solutions
Note orientation
of insert lobes

Markers can be installed in any of the four available
paddle orientations:
Install markers before mounting paddles to door
Secure “PUSH” marker on the push side of the door
using screw supplied.
Secure “PULL” marker on the pull side of the door
using screw supplied.
ASSA ABLOY is the global leader in door opening solutions, dedicated
to satisfying end-user needs for security, safety, and convenience
Optional Paddle Marker Installation
STEP 5: Installation of Paddles
Attach paddle to the chassis in the desired orientation by
inserting the axle through the pivot hole
Slide cover over paddle
Press cover against door surface
Slide back until mounting holes align
with those in chassis
Install #8-32 x 5/16” cover screws
Install strike into the door frame
STEP 6: Installation of Covers
Cover should hook underneath
chassis on edge opposite
mounting screws
Copyright © 2011, Corbin Russwin, Inc., an ASSA ABLOY Group Company.
All rights reserved. Reproduction in whole or in part without the express written
p
ermission of Corbin Russwin, Inc. is
p
rohibited.