Assa Abloy Yale Essential Series User manual

Essential Series - YDME 80

YDME 80 - Essential Series
Important Tips
1.
scanner clean after using to ensure the normal use.
2. Please do not use the corrosive cleaner liquid on the lock surface. Clean
it with furniture spray wax.
3. Please adjust the door strike plate when the door deformed causing unable
to open the door or mortise unable to stretch out and draw back.
4. When adding new users, please keep the user No. for future use.
5. Power supply: 8 1.5V battery 5 Emergency battery:9V.
6.
to open the door and keep them in a reachable place.
7. For those locks with electronic deadbolt function, if locked inside, only the
master code or override key can open the door and after it was opened, no
matter inside or outside, the deadbolt function lost. But you can still use the
deadbolt function inside the door by hand.
The right way of using
Wrong way of using
Tips:
Keep your finger clean and make sure to let it touch the metal frame of the scanner.
incorrect incorrect incorrect incorrect incorrect
correctcorrect correct correct
Name for the locks parts
YDME 80 - Essential Series

CONTENTS
Essential Series YDME 80
4
4
4
5
6
6
6
7
Operation Guidance
Starter Sets
Change the Master Code
Adding user 5
Delete User
Door open operation
Use of the override key
Use of the external 9V battery
Change Battery
Operation Guidance
◎
◎
Keypad Instruction
Touch the screen for electricity with sound "welcome to use".
Pressing "#" at the menu situation means confirm.
Voice indication
Each pressing of the keypad with a "Beep" sound.
Voice with "Please input again" for the incorrect operation.
Voice with "please change the battery" when low battery.
The keypad was lock for one minute if incorrect input for 3 times with the
sound"3
times of incorrect password, the keypad was lock".
When low battery, the voice indication will be lock automatically. With long
"Beep" for successfully operation, "Beep, Beep, Beep" for incorrect operation,
" Beep, Beep,
Beep, Beep" for low battery and " Beep, Beep" for other cases.
◎
◎
◎
◎
Factory Settings
The factory default master code is “111111”. please change the master code on
the initial use. After changing, all the existing useres are deleted automatically.
Reset
keep the battery on and press the “Reset ” button, when hearing the sound”
Successfully operation", means the lock was reseted successfully and the
master
code was back to "111111", all the users added before were deleted.
Changing the master code
Operation
Touch the screen Touch the screen, the blue light on, sound with
"Welcome to use”
Input "#+6-digit
master code
Voice with "0,#,change the master code,1,#,
add user,2,#,delete user".
Operation note
Press "0","#" button
Input a new code(6 digits)
Input the new code again
voice with" Change the master code”
Voice with" Please input a new 6 digits code”
Voice with" please input the new code again."
Voice with " Successfully operation”
Successfully operation
The factory default master code is “111111”. Please change the master code on the
initial use. After the master code is changed, all the exist users are deleted automatically.
4

5 6
Essential Series YDME 80 Essential Series YDME 80
Adding user
Operation
touch the screen Touch the screen, the blue light on, sound with
"Welcome to use”
Voice with "0,#,change the master code,1,#,
add user,2,#,delete user".
Input "#+6-digit
master code
Press "1","#" button
Enroll new code
Enroll
Successfully operation
Voice with " please input a new 6-digit code",
then " please input the new code again".
When hearing voice with" Card please", please
put the card at the card reading area.
Voice with " Successfully operation”
Attention: " 111111" can not be set as your new code. voice with "Beep, Beep, Beep",
when you new code was the same as your old ones. 32 users can be added.
Operation note
voice with" Adding user”
When hearing voice with" please press your
hearing • Please,take off your nger".Please
repeatthis for 4 times
Operation
Delete User
Operation note
touch the screen
Input "#+6-digit
master code
Successfully operation Voice with " Successfully operation”
Touch the screen, the blue light on, sound with
"Welcome to use”
Voice with "0,#,change the master code,1,#,
add user,2,#,delete user".
Input the User ID
Input the User ID
Press "2","#" button
voice with " please input the user ID”
voice with " please input the user ID again”
voice with" Delete user”
Enroll card
Operation Guidance
Door open operation
Touch the screen, the blue light on, sound with
"Welcome to use”
Operation
touch the screen
Use code or card
to open the door
Ways of opening:
Input the valid code ( has been enrolled)
Put the card ( had been enrolled) at the card
reading area.
If no incorrect operation, there will be a sound
"Beep" then you can press the handle to open
the door. If operate incorrectly, there will be a
sound " Please try again".
(1)
(2)
Turn the handle and
open the door
Operation note
Use of the override key
Press and push
to the right.
Use of the external 9V battery
For Low working voltage, or low battery and not able to change the new
battery, you can use the external 9 V battery to open the door.
Pull the panel cover Connect the external 9 V battery
according to their electrode.
Install back the panel cover
after door open.

7
Essential Series YDME 80
Change Battery
Steps
Use the socket screw wrench to loosen and take
off the copper loop. (Picture 1 Bellow)
Take off the battery cover. ( picture2, 3)
Take off the all old batteries
install with new ones
Place back the battery cove and tighten the copper loop.
1 Pay attention to the electrode when installing
the new batteries.
2.Do not mix the old ones with the new ones.
3.Please put the old batteries at the recycle
place to keep good environment.
.
1.
loosen and take off the copper loop.
Use the socket screw wrench to 2.
and the back lock cover.
Slightly pull the copper loop 3.
and the back lock cover.
Take off the copper loop
Remark: