Ballard Designs Fenwick MQ112 User manual

PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 4-15-2020 Page 1 of 2
PRODUCT NAME: Fenwick Media Console
ITEM NUMBER: MQ112
ASSEMBLED DIMENSIONS : 27”H x 98 5/8”W x 19”D
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN CHINA

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 5
Ltr.
A24
B 4
Qty. Included Hardware
Ltr.
E
F
6
4
Qty. Components
D1
TOOLS NEEDED:
-Flathead Screwdriver
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
NOTE: To avoid accidentally
discarding small parts or hardware,
retain all carton contents until
assembly and installation are complete.
Assemble in location for intended use.
Wood Plugs
Shelf Support
Shelves (E)
Console (D)
Doors (F)
Wall Anchoring
(Anti-tip) Kits
See Page 5
WARNING
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
ANCHORING HARDWARE INCLUDED
C2
Shelves (D)
Hardware Packet
Door (E)

STEP 1: Place Console (D) in location for use. Console is equipped with Rotary Levelers in each
corner accessible from INSIDE. Insert a Flathead Screwdriver into hole and turn clockwise/counter-
clockwise until Console is level. When complete, insert Wood Plugs (B) to cover holes.
(D)
(B)
Page 3 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Assemble in location for intended use.
STEP 2: Locate and position Shelf Supports (A) into pre-drilled holes. Carefully lay Shelves (E) into
place, allowing them to rest level upon padded surface.
(A)
(E)

Page 4 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Cleaning & Care:
DO NOT use alcohol based products or spray polisher as
they can damage the finish. Dust with soft cloth.
Assemble in location for intended use.
STEP 3: Align and place wheels on bottom of two Doors (F) into REAR TRACK in base of
Console (D) then gently push top of each Door into Console. NOTE: Be certain track guides on the
top of each door are pushed in and locked before pushing door in. Once top of Door is aligned with
top rear track, push button on guide assembly and guide will pop up and into track.
Repeat process for both doors in FRONT TRACK.
U
p
p
e
r
T
r
a
c
k
L
o
w
e
r
T
r
a
c
k
W
h
e
e
l
Po
p
-o
u
t
T
r
ack
G
ui
d
e
(D) (F)

Page 5 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Installation:
Ltr.
A2
Small Screw
Retention Belt
Qty. Hardware Included
B2
Large Screw
C4 Bracket
D2
WALL ANCHORING HARDWARE (ANTI-TIP)
1. Place furniture against wall at desired location then locate and mark a Wall Stud behind unit.
2. Corresponding to Stud location, attach one Bracket (C) to back of unit using Small Screw (B).
3. To keep hardware out of view after installation, attach remaining Bracket (C) INTO WALL STUD
with Large Screw (A) 2 inches below Bracket attached to back of unit.
4. Move unit into place, align Brackets then connect both using Retention Belt (D).
5. Confirm Belt is securely laced and locked.
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
W
A
L
L
S
TUD
WALL BRACKET MUST BE ATTACHED TO WALL STUD
(A)
(B)
(C)
(D)
R
e
presen
t
a
tiv
e
Fu
r
nitu
r
e
I
tem