Ballard Designs SK066 User manual

Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 7-20-2021 Page 1 of 4
PRODUCT NAME: Trieste Server Hutch
ITEM NUMBER: SK066
ASSEMBLED DIMENSIONS : 46”H x 26.5”W x 19”D
MADE IN INDONESIA
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 4
Ltr.
A 4
B4
Qty. Hardware Included
Ltr.
F
G
1
3
Qty. Components
C
REQUIRED TOOLS:
Phillips Screwdriver,
Allen Wrench (included)
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
D
E
1
2
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
ANCHORING HARDWARE INCLUDED
WITH BASE CABINETS
Hutch (F)
12
Shelves (G)
(Ship installed inside Hutch)
H2Moulding (H)
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
*Allen Bolts
*Flat Washers
Allen Wrench
*4 required to join Hutch to Base. 2 extra used when joining multiple side-by-side units.
**2 required to join Hutch to Base. 1 extra used when joining multiple side-by-side units.
**Connector Plates
Cleaning and Care
Periodically dust with a soft, dry cloth.
Prevent finish damage: do not use alcohol based
cleaners or polishers. Promptly remove spills.
Shelf Supports
(Ship installed with Shelves inside Hutch)
SAFETY NOTICE/WALL ANCHORING HARDWARE
Anchoring Hardware Kits are included with Trieste Console Cabinets (SK067, SK068).
After attaching Hutch to Base Cabinet use Anchoring Hardware to
ANCHOR HUTCH TO WALL STUD(S). See Page 4 for details.
Assemble in location for intended use.

Fig. 1
Fig. 2
SHELVES: Use a Phillips Screwdriver to
remove Set Screws. Lift Shelf (G) out.
Remove and reposition Shelf Supports (E).
Replace Shelf then reinsert and tighten Screws.
LEVELERS: Console (SOLD SEPARATELY) is
equipped with Rotary Levelers. If necessary, adjust-
ments may be made by carefully lifting applicable
corner and turning Leveler clockwise/counterclockwise.
Cabinet/Console base
SOLD SEPARATELY
Adjust Levelers BEFORE anchoring
unit to wall.
Page 3 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
WARNING: To prevent a dangerous tip-over accident, Hutch must be secured to
base using Brackets as illustrated in this step.
SETUP: SINGLE: Place Trieste Console (sold separately) in location for installation then carefully lift
and place Hutch (F) onto Console top. Align side and back edges then position two Connector Plates (D)
as illustrated (Fig. 1). Secure using Allen Bolt (A) with Flat Washer (B). Snap on Moulding (H)
MULTIPLE: Complete steps above then use Connector Plates (D) to join and secure all units (Fig. 2).
NOTE: Console and Hutch units all sold separately.
(D)
(A)
(A)
(B)
(B)
(C)
(C)
(H)
Use Moulding on open ends.
Omit when joining multiple units.
N
O
T
E
(D)
(G)
(E)

Page 4 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(A)
(D)
(B)
(C)
W
A
LLS
T
U
D
WALL BRACKET MUST BE ATTACHED TO WALL STUD
WALL ANCHORING HARDWARE (ANTI-TIP) INCLUDED WITH CABINET/CONSOLE BASE
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
Ltr.
A 4 Small Screw
Retention Belt
Qty. Hardware Included
B4Large Screw
C4Bracket
D2
1. Place Hutch against wall at desired location then locate and mark a Wall Stud behind unit.
2. Corresponding to Stud location, attach one Bracket (C) into WOOD BANDING on back of Hutch
using Small Screws (A). If Screw is not driven into wood it may pull out during a tip-over.
*NOTE: HUTCH MUST BE ATTACHED WITH BRACKETS TO BASE CONSOLE!
3. To keep hardware out of view after installation, attach remaining Bracket (C) INTO WALL STUD
with Large Screws (B) 2 inches below Bracket attached to back of unit.
4. Move unit into place, align Brackets then connect both using Retention Belt (D).
5. Confirm Belt is securely laced and locked.
ATTENTION: Do not anchor Consoles to wall onto which a Hutch is to be installed.
Hutches are anchored to wall after attachment to Console Bases.
IMPORTANT
*Hutch MUST be bracketed to
Console Base.
Anchor HUTCH to Wall Stud.
Do not anchor Console Bases
when topping with a HUTCH.
Anchor Hutch ONLY