Ballard Designs BUNNY WILLIAMS MA232 User manual

PRODUCT NAME: BW Entry Cabinet Center Hutch
ITEM NUMBER: MA232
DIMENSIONS OF ITEM ASSEMBLED: 65 1/4”H x 42”W x 19 1/4”D
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATE: 2/17/2017 Page 1 of 7
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN CHINA

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 7
TOOLS NEEDED:
-Requires a screwdriver.
-Power drill suggested.
-Assembly requires 2 or more people.
Hardware Located
Here (A-F)
Shelves (G)
Shelves (G)
Ltr.
G 3
stnenopmoC.ytQ
NOTE: When unpacking, lay the parts on
a padded surface such as the packaging provided.
Be sure to locate all hardware before throwing
away any packaging.
NOTE: Assemble the Hutch in desired location for use.
L-Brackets
Long Screws
Ltr.
C
stroppuSflehSB
2
12
Qty. Hardware Included Ltr. Qty.
A
16
D 8
Anchors
Hardware Included
Cylinder (H)
H 2 Finials (H)
E 8
F 2 Brackets
Small Screws

Page 3 of 7
STEP 1:
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
NOTE: Assemble the Hutch in desired location for use.
STEP 2:
Screw the Finials (H) into the top corners of the Hutch.
(B)
(G)
(H)
Place the Shelf Supports (B) at the desired heights and lay the Shelves (G) on the
Supports. The plate groove should be located at the back of the Hutch.

Page 4 of 7
STEP 3:
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
NOTE: Assemble the Hutch in desired location for use.
Carefully place the Hutch onto the Console (MA231).
STEP 4: Connect the Hutch to the Base by centering the Brackets (F) evenly over the Hutch and
the top bar on the Base with two screws holes on each side (as shown). Secure into place
using the Small Screws (E).
(MA231)
(MA232)
(F)
(E)
NOTE: Attach the
Brackets near the edges
for the best support.

Page 5 of 7
STEP 5:
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
NOTE: Assemble the Hutch in desired location for use.
Center the Cabinet in front of two Studs and mark the Wall. Push the unit against the Wall.
STEP 6: Slide the L-Brackets (C) over the top corner of the Hutch in front of the previously marked
Stud and mark the Wall at the top of the L-Bracket.
NOTE: It is important that the L-Bracket is positioned like the picture below in order
to hide the Bracket.
Installing the L-Bracket (C) to a Wall Stud
and the Hutch is REQUIRED before any
use of the product for customer safety.
IMPORTANT:
(C)

Page 6 of 7
STEP 7:
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
NOTE: Assemble the Hutch in desired location for use.
Pull the Hutch away from the Wall and attach the L-Brackets (C) to the Studs using the
Long Screw (A). If there are not Studs in the desired location, lightly tap in the Anchors (D)
and attach the L-Brackets with the Long Screws.
STEP 8: Slide the Hutch underneath the previously installed L-Brackets (C) and use 2 or more of
the Long Screws (A) to attach the L-Brackets to the Hutch.
NOTE: The L-Brackets may not be completely flush with the Hutch’s Top due to the Wall’s
Base Moulding. Only screw into the Bracket holes that are completely on the Hutch Top.
(A)
(C) (D)
(C)
(A)

Page 7 of 7
STEP 9:
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
NOTE: Assemble the Hutch in desired location for use.
If joining the Hutch with a Left or Right Cabinet (MA229 / MA230), remove the side
mouldings on the side(s) being joined to.
STEP 10: Slide the Right & Left Cabinets (MA229 & MA230) next to the Hutch. Install the Right
and Left Cabinet per the instructions provided with the units.
NOTE: Installing the L-Brackets (C) to a Wall Stud for each additional unit
(MA229/MA230) is REQUIRED before any use of the product for customer safety.
(MA229) (MA230)