Ballard Designs Tuscan Center Bookcase with Cabinet MV397 Quick start guide

PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 4-27-2021 Page 1 of 7
PRODUCT NAME: Tuscan Center Bookcase with Cabinet
ITEM NUMBER: MV397
ASSEMBLED DIMENSIONS: 85 3/4”H x 37”W x 18 3/4”D
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
IMPORTED

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 7
NOTE: Assemble in intended area for use.
REQUIRED TOOLS:
-Phillips & Flat Head screwdriver, Pencil
-Power drill (optional)
-Assembly requires 2 or more people.
Wood Shelf (E)
Ltr.
E1
stnenopmoC.ytQ
L-Brackets
Screws
Ltr.
C
stroppuSflehSB
2
12
Qty. Hardware Included Ltr. Qty.
A
16
D 4
Hardware Included
Glass Shelves (F)F2
Wood Plugs
Hardware Located
Here (A-E)
Shelves (E,F)
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
NOTE: To avoid accidentally
discarding small parts or hardware,
retain all carton contents until
assembly and installation are complete.
Serious or fatal crushing injuries can occur from a furniture tip-over
WARNING
Tip-Over Hazard
WALL BRACKET MUST BE ATTACHED TO WALL STUD
Prevent tipping accidents. Anchor your furniture.

(D)
(F)
(B)
(E)
(B)
NOTE: Assemble in intended area for use.
STEP 1: INSTALL SHELVES
Determine shelf height, then insert Shelf Supports (B) into pre-drilled holes. Gently lay in Wood Shelf (E)
then Glass Shelves (F). All should rest level upon each Shelf Support.
STEP 2: LEVELERS
If necessary, the Bookcase may be leveled by adjusting LEVELERS located on the
bottom of each corner which are accessible INSIDE the Cabinet. Use a Flat Head Screwdriver to turn
clockwise/counterclockwise to adjust. Cover holes with Wood Plugs (D) when complete.
Page 3 of 7
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

(C)
STEP 4: MARK LOCATION OF WALL BRACKETS
With Bookcase against the wall, slide L-Brackets (C) over top corner and position at Wall Stud(s). Use
pencil to mark wall at top of Wall Bracket.
NOTE: In order to hide wall brackets, orient as shown below.
WALL
STUD
Page 4 of 7
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
WARNING
Tip-Over Hazard
WALL BRACKET MUST BE ATTACHED TO WALL STUD
Prevent tipping accidents. Anchor your furniture.
STEP 3: LOCATE AND MARK WALL STUDS FOR ANTI-TIP HARDWARE
Bookcase includes two L-Brackets (C), at least one of which MUST BE SECURED TO A WALL STUD.
First, push Bookcase against wall and position over wall stud(s). Use a pencil to mark stud locations.
Wall Studs
AT LEAST ONE BRACKET (OPTIMALLY BOTH)
MUST BE ANCHORED TO A WALL STUD
NOTE

Page 5 of 7
A
C
STEP 5: ATTACH BRACKETS TO WALL
Carefully pull Bookcase away from wall and attach Wall Brackets (C) at marked locations.
Use Screws (A) for anchoring and securing Bracket to a Wall Stud.
Wall Stud
STEP 6: ATTACH BRACKETS TO TOP OF BOOKCASE
Carefully slide Bookcase under each of the previously installed L-Brackets (C) and use two or more
Screws (A) to attach L-Brackets to top of Bookcase.
NOTE: Your wall base molding may prevent Bookcase from going back far enough for Bracket to
entirely cover top. Use screws only in those holes that cover.
(A)
(C)
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Wall
Stud

Plug electrical cord into an outlet. Cabinet is equipped with an “Easy Touch” dimmer
control which allows for three levels of brightness. To operate, touch upper right steel plate.
STEP 7: BOOKCASE LIGHTING
Easy Touch
Touch steel plate
for 3-level
light control
Cleaning & Care:
DO NOT use alcohol based products or spray polisher as they can damage the finish.
Dust with soft cloth. Finish can be affected by heat or extended contact with oils or wine.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 6 of 7

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 7 of 7
HALOGEN BULB REPLACEMENT:
Insert the new Bulb (A) into the Fixture Body (C) Socket using a tissue or soft cloth (oil from the
skin my damage the bulb). Replace the Lens Cover (B) by twisting it clockwise back into place.
1
Qty.
Halogen JCD G8 120V 25W
Replacement Bulb (A)
NOT INCLUDED
Item needed
Unplug the unit from the wall. Remove the Lens Cover (B) from the Fixture Body (C) by turning it
counter clockwise and pulling it away from the unit. Remove the old Bulb (A) by pulling it straight
out in a horizontal direction.
(B)
(C)
(B)
(C)
(A)
NOTE: Save this page for future bulb replacement.