BEGA 77 004 Manual

Installation and Technical Information
BEGA
In the interest of product improvement, BEGA reserves the right to make technical changes without notice.
Replacement Parts
Accessories
Please refer to the appropriate
accessory installation sheet for
further instruction when applicable.
BEGA 1000 Bega Way, Carpinteria, CA 93013 [phone] Fax [phone] www.bega-us.com © Copyright BEGA-US 2018
Bega-US Architectural Lighting Fixtures and Products
http://www.bega-us.com/groupdimimages.aspx?imagetype=sk&groupid=19b [6/1/2009 10:42:14 AM]
Recessed wall - linear oodlight LED - asymmetric 77 004
Tools Required:
4mm Torx key
Protection Class: IP 67
Weight: 5.3 lbs.
Dimensions
A: 15-3/4 “
B: 2-1/8 “
C: 4 “
Relamping/Maintenance
NO relamping required.
Lamp: 3.7W LED 24V DC
77 004
8/20/2018
Page 1 of 2
Description
Consult factory
Part No
Remote 25W LED driver and box 19 580
Remote 50W Dimming LED driver and box 19 591
Potting Compound (In-ground install only) 77 269
Notice to Installer for 77 004:
1. Luminaire requires a remote 24V DC Class 2 safety isolation LED driver (by others) suitable
for the intended LED wattage load. See BEGA 19 580 or BEGA 19 591 specication sheet
for information.
2. Installer is responsible for supplying correct wire to account for voltage drop from LED driver.
3. No relamping required.
4. Luminaire is supplied with (1) ft. of cable.
5. Back housing must be installed so that the front face of the back housing is ush with the
nished wall.
6. Luminaire is non-IC rated. Insulation must be at least 3” from luminaire.
7. In conformance with UL Standard 1598, a silicone based sealant MUST be used between
luminaire and supporting wall.
8. Requires a 24V DC class 2 electronic power supply to operate intended LED
BB7004LED (back housing) installation in hollow wall construction:
1. Attach back housing to wooden block via mounting holes with (2) screws (by others).
2. Connect conduit. Pull wires for electrical connections to be made later.
BB7004LED (back housing) installation in poured concrete:
1. Attach back housing to concrete form using (2) screws (by others), such that the front face of
the back housing is ush with the nished surface.
2. Connect conduit to back housing.
3. Pour concrete. NOTE: Do not pump or drop concrete directly on top of the back housing.
4. Remove form and pull wires for electrical connections to be made later.
LED luminaire installation for 77004:
1. Make necessary wiring connections inside the housing
BROWN LEAD TO INCOMING POSITIVE LEAD FROM REMOTE 24V LED DRIVER
BLUE LEAD TO INCOMING NEGATIVE LEAD FROM REMOTE 24V LED DRIVER
2. Place a small bead of silicone around the back side of the luminaire ange that will come in
contact with the nished wall (exterior applications only).
3. Insert LED luminaire into back housing. Make sure mounting tabs are positioned to engage
back housing when turned.
4. Turn the (2) 4mm Torx screws on the faceplate clockwise evenly up to the stop to engage the
back housing and wedge the luminaire into place.
NOTE: FOR INGRADE INSTALLTIONS, WIRING CONNECTIONS MUST BE WATER TIGHT.
SEE DIAGRAM. POTTING COMPOUND TO COVER WIRES AND CUT END OF CABLE CAN
BE PROVIDED BY BEGA, SEE ACCESSORIES.
POTTING COMPOUND: FOR
IN-GROUND INSTALLS ONLY

Installation and Technical Information
BEGA
In the interest of product improvement, BEGA reserves the right to make technical changes without notice.
BEGA 1000 Bega Way, Carpinteria, CA 93013 [phone] Fax [phone] www.bega-us.com © Copyright BEGA-US 2018
Recessed wall - linear oodlight LED - asymmetric 77 004
77 004
8/20/2018
Page 2 of 2
Product Safety Warnings:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
SUITABLE FOR WET LOCATIONS.
MIN 90°C SUPPLY CONDUCTORS.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT
BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.
CONVIENT AUX EMPLACEMENTS MOUILLÉS.
LES FILS D’ALIMENTATION 90°C MIN.