BEGA 84 235 Manual

Installation and Technical Information
BEGA
Due to the dynamic nature of lighting products and the associated technologies, luminaire data on this sheet is subject to change at the discretion of BEGA North America. For the most current technical data, please refer to bega-us.com
BEGA 1000 Bega Way, Carpinteria, CA 93013 [phone] © copyright BEGA 2022
High performance oodlight - wide beam 84 235
Dimensions
A: 9-3/4
B: 17-3/4
C: 2-1/8
Maintenance:
Clean regularly with solvent-free cleaner
removing dirt and debris. Do not use high
pressure cleaners.
Replacement Parts
See label inside of xture for LED replacement
part number.
Consult factory for all other replacement
components.
Accessories
Please refer to the appropriate accessory installation
sheet for further instruction when applicable.
Surface mount conduit wiring box 19 593
Direct burial wiring box 19 594
Earth spike 70 204
Pole cap - 3” O.D. pole tenon 70 249
Wood screw 70 252
Tube clamp 70 280
Screw clamp 70 283
Pole mount arm 70 379
Mounting block 79 511
Pole coupler 71 042
Updated: 08/22/22
84 235 1 of 2
Notice to Installer:
1. See page 2 for specic product safety warnings.
2. Provided with 1/2” IPS threaded nipple for direct attachment to pole couplers, cast
wiring boxes, or other mounting accessories either by BEGA or others.
3. Floodlight is provided with 4’ of 18/5 SJTOW cable.
Installation: Luminaire
1. Route cable to splice location.
2. Make supply wiring and luminaire wiring connections:
MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE
NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE
GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE
Dimming (if applicable):
DIMMING CONTROL (+) TO POSITIVE LUMINAIRE DIM CONTROL WIRE
DIMMING CONTROL (-) TO NEGATIVE LUMINAIRE DIM CONTROL WIRE
3. Insert male threaded part from oodlight into coupler on pole, wiring box, or other
mounting accessory (Figure 1).
4. Tighten hexagon nut on top of connector assembly using an adjustable wrench to
secure the oodlight into place.
5. To adjust head angle, use 6mm hex head screwdriver to loosen screw at aiming
joint. Aim luminaire head as needed and tighten screw to secure into place. (Figure
2).
Figure 1:
Figure 2:
Aiming Joint
Overview:
LED Watts: 95.6W
System Watts: 107.0W
Controllability: 0-10V dimmable
Weight: 12.1 lbs.
Protection Class: IP65
Tools Required:
• Adjustable wrench
• 6mm hex head screwdriver

Installation and Technical Information
BEGA
Due to the dynamic nature of lighting products and the associated technologies, luminaire data on this sheet is subject to change at the discretion of BEGA North America. For the most current technical data, please refer to bega-us.com
BEGA 1000 Bega Way, Carpinteria, CA 93013 [phone] © copyright BEGA 2022
Product Safety Warnings:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY
A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED.
SUITABLE FOR WET LOCATIONS.
MIN 90°C SUPPLY CONDUCTORS.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE
QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.
CONVIENT AUX EMPLACEMENTS MOUILLÉS.
LES FILS D’ALIMENTATION 90°C MIN.
Updated: 08/22/22
2 of 2
84 235
High performance oodlight - wide beam 84 235