BEGA 84208 Manual

Installation and Technical Information
BEGA
Due to the dynamic nature of lighting products and the associated technologies, luminaire data on this sheet is subject to change at the discretion of BEGA North America. For the most current technical data, please refer to bega-us.com
BEGA 1000 Bega Way, Carpinteria, CA 93013 [phone] © copyright BEGA 2022
Figure 1:
Overview:
LED Watts: 18.2W
System Watts: 22.0W
Controllability: 0-10V, TRIAC, and ELV dimmable
Weight: 4.4 lbs.
Protection Class: IP65
Tools Required:
• 3mm hex head screwdriver
• Phillips head screwdriver
• Adjustable wrench
• 5mm hex head screwdriver
Performance oodlight - very narrow beam 84 208
Dimensions
A: 5-3/4
B: 9
C: 3-7/8
D: 4
Maintenance:
Clean regularly with solvent-free cleaner
removing dirt and debris. Do not use high
pressure cleaners.
Replacement Parts
See label inside of xture for LED replacement
part number.
Consult factory for all other replacement
components.
Accessories
Please refer to the appropriate accessory installation
sheet for further instruction when applicable.
Elliptical spread lens 71 120
180° Glare shield 71 118
360° Glare shield 79 829
Updated: 05/24/22
84 208 1 of 2
Notice to Installer:
1. See page 2 for specic product safety warnings.
2. In conformance with UL Standard 1598, a silicone based sealant must be used
between luminaire and supporting surface.
3. Luminaire mounts directly to standard recessed 4” octagonal wiring (by
others), using mounting plate provided.
Installation: Luminaire
1. Loosen the (1) 3mm hex head set screw on the xture canopy to remove luminaire
base.
2. Feed luminaire wiring through the luminaire base and mounting plate into wiring box
(by others).
3. Make supply wiring and luminaire wiring connections inside the wiring box:
MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE
NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE
GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE
Dimming (if applicable):
DIMMING CONTROL WIRE (+) TO POSITIVE DIM LUMINAIRE WIRE
DIMMING CONTROL WIRE (-) TO NEGATIVE DIM LUMINAIRE WIRE
4. Attach provided mounting plate directly to a 4” standard octagonal wiring box using
the (2) phillips head screws (provided).
5. Important! Place a small bead of silicone around the back side of the mounting plate
that will come in contact with the nished surface (exterior applications only). Failure
to do so can cause water entry and will void warranty.
6. Place luminaire base over the mounting plate. Tighten nuts (provided) on the studs to
secure. (Figure 1)
7. Replace luminaire canopy (with luminaire attached) and align to desired orientation.
Tighten (1) 3mm hex head set screw to secure into place.
8. To adjust head angle, use 5mm hex head screwdriver to loosen screw at aiming joint.
Aim luminaire head as needed and tighten screw to secure into place.

Installation and Technical Information
BEGA
Due to the dynamic nature of lighting products and the associated technologies, luminaire data on this sheet is subject to change at the discretion of BEGA North America. For the most current technical data, please refer to bega-us.com
BEGA 1000 Bega Way, Carpinteria, CA 93013 [phone] © copyright BEGA 2022
Product Safety Warnings:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY
A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED. SUITABLE FOR MOUNTING WITHIN 1.2 m (4 ft) OF THE GROUND.
SUITABLE FOR WET LOCATIONS.
MIN 60°C SUPPLY CONDUCTORS.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE
QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS. PEUT
ÊTRE INSTALLÉ À MOINS DE 1,2 m (4 pi) DU SOL.
CONVIENT AUX EMPLACEMENTS MOUILLÉS.
LES FILS D’ALIMENTATION 60°C MIN.
Updated: 05/24/22
2 of 2
84 208
Performance oodlight - very narrow beam 84 208