Belson Outdoors R6-P User manual

111 North River Road
North Aurora, IL 60542
Phone: [phone]
Fax: [phone]
[email protected]
2014-10-08 – Page 1
Model # R6-P Instructions Sheet
www.belson.com
TRADITIONAL RECTANGULAR PORTABLE TABLE
Inspect the shipment for damage and conduct a thorough
inventory to determine that all parts and hardware are present and
verify that all tools needed for assembly are on hand.
We are not responsible for items discovered missing or
damaged after 72 hours from time of delivery!
If you have a question regarding anything covered in this manual,
please contact your sales representative.
It is very important to use care when assembling and moving
the equipment. Do not drag the equipment across any surface.
This equipment requires periodic cleaning with a sponge or
soft cloth and a solution of mild detergent and water. You may
also use a solution of 50/50 bleach/water if necessary. Do not
clean with a solvent or petroleum-based products.
Apressure washer may be used for cleaning (follow
manufacturer’s recommendations for nozzle type and distance
from surface to avoid damaging finish).
You may use a hair dryer to smooth out the plastisol/PVC
coating if it becomes dented.
Furniture must not be used other
than for its intended purpose. It
should be inspected regularly for
loose, missing or broken hard-
ware and general instability.
Furniture that is damaged or
appears to be unstable must be
removed from service and
repaired or replaced. Repairs
must be made using only factory
authorized parts and methods.
Recommended Crew:
Minimum 2 People
Tools Required:
Cardboard from Packaging / Drop Cloth
Level
Ratchet with 1/2” Socket
1/2” Open-End or Box-End Wrench
Assembly Time (approximately):
1 hour
WARNING!

TABLE TOP
QTY. 1
SEAT
QTY. 2
DIAGONAL BRACE
QTY. 2
“H” FRAME FOR
RECTANGLE TABLE
QTY. 2
2014-10-08 – Page 2
www.belson.com
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED.
5/16”-18X1-1/2” GRADE 5 ZINC
HEX BOLT
QTY. 16
5/16” ZINC FLAT WASHER
QTY. 32
5/16” NYLON LOCK NUT
QTY. 16
5/16” BOLT GUARD
QTY. 16

2014-10-08 – Page 3
www.belson.com
STEP #1:
Please Note: Use caution throughout the assembly/placement of the table. Do not drag or slide any part of
the table across any surface. Lay table top upside down on the packaging material or a drop cloth on a smooth,
flat surface to avoid damaging/scratching the product.
STEP #3:
Attach diagonal braces as shown. Hand tighten hardware at this time.
STEP #2:
Fit the frame to the top as shown, and secure
with hex bolt, two washers, nylon lock nut and
bolt guard at each connection. Hand tighten
hardware at this time. Important: The frame
must be positioned under the table with
the elbow side of the Angle Brackets
pointing away from the table center and
the L-Brackets “opening” toward the table
end (see details to the right).
TABLE FRAME
TABLE TOP
(UPSIDE DOWN)
NYLON
LOCK NUT
FLAT
WASHERS
HEX BOLT
BOLT
GUARD
NYLON
LOCK NUT
FLAT
WASHERS
HEX
BOLT
BOLT GUARD
NYLON LOCK NUT
FLAT
WASHERS
HEX BOLT
BOLT
GUARD
DIAGONAL BRACE
TO TABEL TOP
AND H-FRAME
1 - 5/16” X 1-1/2” HEX BOLT
2 - 5/16” FLAT WASHER
1 - 5/16” NYLON LOCK NUT
1 - 5/16” BOLT GUARD
H-FRAME TO TABLETOP
HARDWARE DETAIL
1 - 5/16” X 1-1/2” HEX BOLT
2 - 5/16” FLAT WASHER
1 - 5/16” NYLON LOCK NUT
1 - 5/16” BOLT GUARD Angle BracketL-Bracket

2014-10-08 – Page 4
Table tops will be approximately 30” above the ground.
Seats will be approximately 18” above the ground.
Dimensions shown may vary based on installation and manufacture.
www.belson.com
STEP #5:
Please Note: this is at least a two-person
operation. Carefully turn table right side up
and tighten all hardware in an alternating
pattern to keep the frames straight under the
tops and seats. Use a level to verify table
frame, top and seats are level and plumb.
Pick table up off ground and carry to desired
location, using caution not to drag table
across any surface.
STEP #4:
Fit the seats to the attachment brackets as shown, and secure each seat with hex bolt, two washers, nylon lock nut
and bolt guard at each connection. Hand tighten hardware at this time.
SEAT
NYLON
LOCK NUT
FLAT WASHERS
HEX BOLT
BOLT GUARD
H-FRAME TO SEAT
1 - 5/16” X 1-1/2” HEX BOLT
2 - 5/16” FLAT WASHER
1 - 5/16” NYLON LOCK NUT
1 - 5/16” BOLT GUARD
60-1/4”
29-1/4” 71-1/4”
53-3/4”
18”
30”
10-1/4”
2”