Belson Outdoors Picnic Table RP6S User manual

111 North River Road
North Aurora, IL 60542
Phone: [phone]
Fax: [phone]
[email protected]
Model # RPS6 Instructions Sheet
www.belson.com
Recycled Plastic Step Over Picnic Table

www.belson.com
Before assembly, please check to make sure all components are included.
(1) - One Table Top
C - Table Top
D - Seat
D - Seat
H - Seat Cross Support
H - Seat Cross Support
G - Under Seat Support
G - Under Seat Support
N - Angle Support N - Angle Support
O - Center Support
K - Right Leg
K - Right Leg
J - Left Leg
J - Left Leg
(2) - Two Seats
(2) - Two Seat Cross Supports
(2) - Two Under Seat Supports
(2) - Two Angle Supports
(2) - Two Right Legs
(2) - Two Left Legs
(1) - Center Support

www.belson.com
Before assembly, please check to make sure all fasteners are included.
(2) - 3/8” x 4” Hex Head Tap Bolt
(16) - 3/8” x 5” Hex Head Tap Bolt
(8) - 3/8” x 3” Hex Head Lag Bolt
(4) - 3/8” x 2-1/2” Hex Head Lag Bolt
(46) - 3/8” Flat Washer
(16) - 3/8” Nylon Lock Nut
(10) - #12 x 3” Flat Head Phillips Screw
(2) - 5/8” x 1” Cross Dowel
Tools Required for Assembly
(1) - #3 Phillips Drive Bit
(2) - 9/16” Socket Wrench
(1) - 1/4” Flat Head Screwdriver

www.belson.com
Step #1:
Whllle the table top is upside-down, fasten the legs to the under top
supports being sure that the counter bores are pointing toward the
center of the table as shown above. Use ( 1 ) One 3/8" x 5"
Hex Head Bolt along with ( 1 ) One 3/8" Flat Washer
and ( 1 ) 3/8" Nylon Look Nut per hole to Secure.
Note: Do Not tighten bolt completely. This will be done in a later step.

www.belson.com
Step #2:
Whllle the table top is upside-down, fasten the seat cross supports
to the legs. Use ( 1 ) One 3/8" x 5" Hex Head Bolt along with
( 1 ) One 3/8" Flat Washer and ( 1 ) 3/8" Nylon Look Nut
per hole to Secure.
Note: Do Not tighten bolt completely. This will be done in a later step.

www.belson.com
Step #3:
Whllle the table top is upside-down, fasten the angle supports
to the seat cross supports and the center top support. Use ( 1 ) One
3/8" x 2-1/2" Hex Head Lag Bolt and ( 1 ) One 3/8" Flat Washer
per hole to secure.
Note: Be sure to tighten all loose bolts after this step is complete.
Note:
Leg is omitted to show detail.
Do Not Remove.

www.belson.com
Step #4:
Place ( 1 ) One 5/8” x 1” Cross Dowel in each hole of the Center
Support as shown in the diagram below. You may need to tap
the Cross Dowels in to plae. be sure the score on the dowel head is
in line with the length of the Center Support as shown below.
Step #5:
While the table top is upside-down, fasten the center support
to the seat cross supports. Use ( 1 ) One 3/8” x 4” Hex Head
Tap Bolt and ( 1 ) One 3/8” Flat Washer per hole to secure.

www.belson.com
Step #6:
While the table top is upside-down, fasten the under seat supports
to the seat cross supports. Use ( 1 ) One 3/8” x 3” Hex Head Lag
Bolt and ( 1 ) One 3/8” Flat Washer per hole to secure.

www.belson.com
Step #7:
Flip the table upright onto the legs. Please take caution while
flipping the table. At this point in assembly the table weighs
approximately 260 Pounds.

www.belson.com
Step #8:
While the table is upright fasten the seats to the seat cross supports
and under seat supports being sure to center all the holes over boards.
Use ( 1 ) One #12 x 3” Flat Head Phillips Screw per hole to secure.