Belson Outdoors RPD8 User manual

111 North River Road
North Aurora, IL 60542
Phone: [phone]
Fax: [phone]
[email protected]
Model # RPD8 Instructions Sheet
www.belson.com
RECYCLED PLASTIC DELUXE PICNIC TABLE

C - TABLE TOP
( 1 ) - ONE TABLE TOP
D - SEAT
( 2 ) - TWO SEATS
N - CENTER SUPPORT
( 1 ) - ONE CENTER SUPPORT
FP - FASTENER PACK
( 1 ) ONE FASTENER PACK
www.belson.com
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED.
H - SEAT CROSS SUPPORT
( 2 ) TWO SEAT CROSS SUPPORTS
M - RIGHT LEG
( 1 ) - ONE RIGHT SMALL LEG
L - LEFT LEG
( 1 ) - ONE LEFT SMALL LEG
K - RIGHT LEG
( 2 ) - TWO RIGHT LARGE LEGS
J - LEFT LEG
( 2 ) TWO LEFT LARGE LEGS
G - UNDER SEAT SUPPORT
( 2 ) - TWO UNDER SEAT SUPPORTS

www.belson.com
1 - #3 PHILLIPS DRIVE BIT
2 - 9/16” SOCKET WRENCH
ALSO NEEDED FOR THIS ASSEMBLY WILL BE THE FOLLOWING MATERIALS:
16 - 3/8” X 5” HEX HEAD BOLT
8 - 3/8” X 3” HEX HEAD LAG BOLT
46 - 3/8” FLAT WASHER
16 - 3/8” NYLON LOCK NUT
8 - #12 X 3” FLAT HEAD PHILLIPS SCREW
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED.

COUNTER BORE
3/8” FLAT WASHER
3/8” NYLON LOCK NUT
3/8” FLAT WASHER
3/8” X 5” HEX
HEAD BOLT
www.belson.com
STEP #1:
WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE LARGE LEGS TO THE LEFT AND RIGHT TOP
SUPPORTS BEING SURE THAT THE COUNTER BORES ARE POINTING TOWARD THE CENTER OF THE
TABLE AS SHOWN ABOVE. USE ( 1 ) ONE 3/8” X 5” HEX HEAD BOLT AND ( 1 ) 3/8” FLAT WASHER ALONG
WITH, ( 1 ) ONE 3/8” FLAT WASHER AND ( 1 ) ONE 3/8” NYLON LOCK NUT PER HOLE TO SECURE.
NOTE: DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.

3/8” X 5”
HEX HEAD
BOLT
3/8” FLAT WASHER
COUNTER BORE
www.belson.com
STEP #2:
WHILE THE TABLE TOP IS UPSIDE - DOWN, FASTEN THE SMALL LEGS TO THE CENTER TOP SUPPORT
BEING SURE THAT THE COUNTER BORES ARE POINTING AWAY FROM THE TOP SUPPORT AS SHOWN
ABOVE. USE ( 1 ) ONE 3/8” X 5” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER ALONG WITH, ( 1 ) ONE
3/8” FLAT WASHER AND ( 1 ) ONE 3/8” NYLON LOCK NUT PER HOLE TO SECURE.
NOTE: DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.

www.belson.com
STEP #3:
WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE SEAT CROSS SUPPORTS TO THE LARGE LEGS.
USE ( 1 ) ONE 3/8” X 5” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER ALONG WITH ( 1 ) ONE 3/8” FLAT
WASHER AND ( 1 ) ONE 3/8” NYLON LOCK NUT PER HOLE TO SECURE.
NOTE: DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.
3/8” FLAT WASHER
3/8” NYLON
LOCK NUT
3/8” X 5” HEX
HEAD BOLT
3/8” FLAT
WASHER

STEP #4:
WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE CENTER SUPPORT TO THE SMALL LEGS. USE
( 1 ) ONE 3/8” X 5” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER ALONG WITH ( 1 ) ONE 3/8” FLAT
WASHER AND ( 1 ) ONE 3/8” NYLON LOCK NUT PER HOLE TO SECURE.
NOTE: DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.
3/8” FLAT WASHER
3/8” NYLON LOCK NUT
3/8” FLAT WASHER
3/8” X 5” HEX HEAD BOLT
www.belson.com

STEP #5:
WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE UNDER SEAT SUPPORTS TO THE SEAT CROSS
SUPPORTS. USE ( 1 ) ONE 3/8” X 3” HEX HEAD LAG BOLT AND ( 1 ) ONE 3/8” FLAT WASHER PER HOLE
TO SECURE.
STEP #6:
SECURE THE UNDER SEAT SUPPORTS COMPLETELY BY FASTENING TO THE CENTER SUPPORT. USE
( 1 ) ONE 3/8” X 3” HEX HEAD LAG BOLT AND ( 1 ) ONE 3/8” FLAT WASHER PER HOLE TO SECURE.
NOTE: BE SURE TO TIGHTEN ALL LOOSE BOLTS AFTER THESE STEPS ARE COMPLETE.
3/8” FLAT WASHER
3/8” X 3” HEX HEAD LAG BOLT
3/8” FLAT WASHER
3/8” X 3” HEX
HEAD LAG BOLT
www.belson.com

STEP #7:
FLIP THE TABLE UPRIGHT ONTO THE LEGS. PLEASE TAKE CAUTION WHILE FLIPPING THE TABLE. AT
THIS POINT IN ASSEMBLY THE TABLE WEIGHS APPROXIMATELY 315 POUNDS.
www.belson.com

STEP #8:
WHILE THE TABLE IS UPRIGHT FASTEN THE SEATS TO THE SEAT CROSS SUPPORTS BEING SURE TO
CENTER ALL HOLES OVER BOARDS. USE ( 1 ) ONE #12 X 3” FLAT HEAD PHILLIPS SCREW PER HOLE
TO SECURE.
#12 X 3” FLAT HEAD
PHILLIPS SCREW
www.belson.com