Belson Outdoors PARK RANGER User manual

(4) PARK RANGER
“J”LEG
700203
(2) TOP “L” BRACKET
700023 (2) SEAT BRACKET
700004
(2) SEAT BRACKET
700005
(1) CENTER
CHANNEL
700063
(1) CENTER BRACKET
700043
www.belson.comWeb Site:North Aurora, IL60542-0207 1-630-897-0573Fax:P.O. Box 2071-630-897-8489Phone:111 North River Road 1-800-323-5664Toll Free:Principal Plantand General Offices
(2) SUPPORT BRACE
700081 (1) HARDWARE BAG
702313
PARK RANGER
PR-AF FRAME KIT CONTENTS:
Thank you for buying a BELSON OUTDOORS quality product.
PLANK KIT CONTENTS AND PLANK REFERENCES2)
ALUMINUM 6’ AND8’ ASSEMBLY INSTRUCTIONS3)FRAME KIT CONTENTS1)
INDEX
OUTER HOLES
MID RANGE
HOLES
CENTER HOLE
TOPHOLE
(1) CENTER
SPACER
700072
1
700313

REFERENCES FOR ALUMINUM PLANKS
DRAWING REFERENCE LINES:
Layall 5 Planks side by side on a non-
abrasive flat surface that will not
damage the aluminum with the plank
legs facing up as shown (bottom
side up).
Draw a Center Line across all 5 Planks
measuring equal distance from side
edges. Then draw two Lateral Lines
28-1/2”parallel from Center Line on
all boards (this will be your reference
for bracket locations).
TOOLS NEEDED: pencil or marker and tape measure or ruler.
BELSON ALUMINUM PLANK KIT
PLANK KIT CONTENTS:
BOARDS SIZE DEPENDS ON TABLE/KIT MODEL, EITHER 6’ OR 8’ SEE INSTRUCTIONS FOR ASSEMBLY.
ALUMINUM PLANK (5)
6’ OR 8’
57”
28-1/2” 28-1/2”
LAT. LINE
LAT. LINE
ANODIZED ALUMINUM
SEAT END CAP (4)
702032
CENTER LINE
KELLYGREEN TAN ANODIZED
702171 702172 702173
6' ALUMINUM
ANODIZED ALUMINUM
TABLE TOP END CAP (2)
702033
PLANK TOP
CLIP MOUNTED ON CENTER CHANNEL
CLIPS MOUNTED ON SIDE CHANNELS
2
700313
KELLYGREEN TAN ANODIZED
702161 702162 702163
8' ALUMINUM
TOP VIEW
SIDE VIEW
IDENTIFY PLANKPARTS
AND CLIP LOCATIONS PLANK TOP
These locations are for Lateral Components:
When attaching Seat / Seat Brackets and
Top “L” Brackets toAluminumPlanks.
This location is for Center Components:
When attaching Center Bracket, Center Channel
and Center Spacer to Aluminum Planks.

6’ AND 8’ ALUMINUM PARK RANGER ASSEMBLY INSTRUCTIONS
1.- Lay 3 Planks aligned side by side on a non-abrasive flat surface that will not damage the aluminum with legs facing up.
2.- Place 2 Top “L” Brackets aligned with the flat edge along the reference Lateral Lines. Attach each Bracket with 6 clips and
1” carriage bolts mounted in Plank’s side channels as shown. Hand fasten nuts. (see page 2 for clip locations).
3.- Insert 1-1/4” carriage bolt through clip and place in Plank’s center channel aligned with the Center Line. While holding the
clip/bolt, place Center Spacer, Center Channel and Center Bracket as shown. Hand fasten nut. (see page 2 for clip locations).
4.- Align parts assembled in step 4 to Center Line and attach Center Channel’s outer holes to side planks using mounting clips and
1” bolts. Hand fasten nuts. (see page 2 for clip locations).
5.- Verify Center Spacer alignment. Then use clip and 1”
carriage bolt mounted in center Plank’s center channel to
attach Center Spacer’s side hole. (see page 2 for clip locations).
6.- Make sure Planks and Brackets are aligned. Then tighten
all 16 nuts.
7.- Attach Table Top End Caps using 3/4” self-drilling
screws.
TOOLS REQUIRED: 9/16” wrench, 1/2” wrench and powered screw driver or drill with Phillips tip No. 2.
8.- Place brace between 2 table “J”
Legs and insert 3-1/2”
long bolt.
Hand
fasten nut.
10.- Attach loose end of Brace
to Center Bracket outer holes
using 1” bolts / nuts.
Note: Do not fully tighten any of the
nuts from steps 8-10 until step 16 below.
11.- Lay 2 Planks on a non-abrasive flat
surface that will not damage the aluminum with legs facing up.
12.- Align Seat Bracket’s flat edge to Plank’s Lateral Lines as
shown. Attach using clips and 1” carriage bolts mounted in side
channels. Tighten firmly.
13.- Attach Seat End Caps using 3/4” self-drilling screws.
14.- Flip the partial table assembly into an upright position.
15.- Attach Seats to Frame with table legs inside Seat
Brackets as shown. Use 2” bolts / nuts.
16.- Tighten all nuts firmly, including assembled parts in
steps 8, 9 and 10.
17.- The Picnic Table is finished.
9.- Attach Leg set to
inside Top “L” Bracket.
Use 2” bolts / nuts.
Lateral Line Lateral LineCenter Line
Lateral Line
Lateral Line
3
700313