Belson Outdoors RECYCLED PLASTIC ROUND TABLE RT-100 User manual

111 North River Road
North Aurora, IL 60542
Phone: [phone]
Fax: [phone]
[email protected]
Model # RT-100 Instructions Sheet
www.belson.com
RECYCLED PLASTIC ROUND TABLE

J - TABLE TOP
( 1 ) - ONE TABLE TOP
W/ SMALL SPOKE ASSEMBLY
F - SMALL SPOKE ASSEMBLY
B - PLASTIC BRACKET
( 12 ) - TWELVE PLASTIC BRACKET
N - SEAT
( 3 ) - THREE SEATS
FP - FASTENER PACK
( 1 ) - ONE FASTENER PACK
C - LARGE SPOKE
( 3 ) - THREE LARGE SPOKES
H - LEG
( 3 ) - THREE LEGS
A - LEG SUPPORT
( 3 ) - THREE LEG SUPPORTS
Q - SEAT SUPPORT
( 6 ) - SIX SEAT SUPPORTS
R - CENTER PROPELLER
( 1 ) - ONE CENTER PROPELLER
www.belson.com
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED.

www.belson.com
1 - #3 PHILLIPS DRIVE BIT 2 - 9/16” SOCKET WRENCH
ALSO NEEDED FOR THIS ASSEMBLY WILL BE THE FOLLOWING MATERIALS:
18 - 3/8” X 5” HEX HEAD BOLT
36 - 3/8” FLAT WASHER
18 - 3/8” NYLON LOCK NUT
6 - #12 X 3” FLAT HEAD PHILLIPS SCREW
12 - #12 X 2 1/2” FLAT HEAD PHILLIPS SCREW
48 - #12 X 2” FLAT HEAD PHILLIPS SCREW
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED.

STEP #1:
ASSEMBLE THE LARGE SPOKES TO THE CENTER PROPELLER AS SHOWN BELOW. USE ( 1 ) ONE
3/8” X 5” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER, ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER
AND ( 1 ) ONE 3/8” NYLON LOCK NUT PER HOLE TO SECURE.
3/8” X 5” HEX
HEAD BOLT
3/8” FLAT
WASHER
3/8” FLAT WASHER
3/8” NYLON
LOCK NUT
#12 X 2” FLAT HEAD
PHILLIPS SCREW
www.belson.com
STEP #2:
PLACE THE 7” PLASTIC BRACKETS ONTO THE CENTER PROPELLER AS SHOWN ABOVE. ALIGN THE
PRE-DRILLED HOLES IN THE PLASTIC BRACKETS WITH THE PILOT HOLES IN THE CENTER PROPELLER.
USE ( 1 ) ONE #12 X 2” FLAT HEAD PHILLIPS SCREW PER HOLE TO SECURE.

3/8” NYLON LOCK NUT
3/8” FLAT WASHER 3/8” FLAT WASHER
3/8” X 5” HEX HEAD BOLT
www.belson.com
STEP #3:
PLACE THE TABLE TOP ASSEMBLY UPSIDE DOWN ONTO A PIECE OF CARDBOARD OR ANOTHER SOFT
SURFACE TO PROTECT IT DURING INSTALLATION. PLACE THE LARGE SPOKE ASSEMBLY ONTO THE
SMALL SPOKE ASSEMBLY AS SHOWN ABOVE. SLIDE ( 1 ) ONE LEG BETWEEN THE PROPELLERS OF
EACH SPOKE ASSEMBLY. SECURE THE LEGS TO THE SMALL SPOKE ASSEMBLY. USE ( 1 ) ONE 3/8” X 5” HEX
HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER, ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER AND ( 1 ) ONE
3/8” NYLON LOCK NUT PER HOLE TO SECURE.
DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.

www.belson.com
STEP #4:
WHILE THE TABLE IS UPSIDE DOWN, SLIDE THE LARGE SPOKE ASSEMBLY UP TO MATCH THE HOLES
TO THE LEGS. SECURE THE LARGE SPOKE ASSEMBLY TO THE LEGS AS SHOWN ABOVE. USE ( 1 ) ONE
3/8” X 5” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER, ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER AND
( 1 ) ONE 3/8” NYLON LOCK NUT PER HOLE TO SECURE.
BE SURE TO TIGHTEN ALL LOOSE BOLTS AFTER COMPLETING THIS STEP.
3/8” NYLON LOCK NUT
3/8” FLAT WASHER 3/8” FLAT WASHER
3/8” X 5” HEX HEAD BOLT

#12 X 2 1/2” FLAT
HEAD PHILLIPS SCREW
#12 X 2 1/2” FLAT
HEAD PHILLIPS
SCREW
www.belson.com
STEP #6:
FASTEN ( 2 ) TWO SEAT SUPPORTS ONTO EACH END OF ( 1 ) ONE LEG SUPPORT. SE SURE THAT EACH
SEAT SUPPORT WHEN FASTENED ARE POINTING IN THE SAME DIRECTION, AND THE COUNTERSINKS
IN THE LEG SUPPORT ARE FACING AWAY FROM THE SEAT SUPPORTS AS SHOWN ABOVE. USE ( 1 ) ONE
#12 X 2 1/2” FLAT HEAD PHILLIPS SCREW PER HOLE TO SECURE.
STEP #5:
PLACE THE 7” PLASTIC BRACKETS ONTO THE SEAT SUPPORTS AS SHOWN BELOW. ALIGN THE
PRE-DRILLED HOLES IN THE PLASTIC BRACKETS WITH THE PILOT HOLES IN THE SEAT SUPPORTS.
USE ( 1 ) ONE #12 X 2” FLAT HEAD PHILLIPS SCREW PER HOLE TO SECURE.

www.belson.com
STEP #7:
WHILE THE TABLE IS UPSIDE DOWN, PLACE THE SEAT SUPPORT ASSEMBLY ONTO THE LEGS AS
SHOWN ABOVE. ALIGN THE PRE-DRILLED HOLES IN THE SEAT SUPPORT ASSEMBLY WITH THE PILOT
HOLES IN THE LEGS. USE ( 1 ) ONE #12 X 3” FLAT HEAD PHILLIPS SCREW PER HOLE TO SECURE.
#12 X 3” FLAT HEAD
PHILLIPS SCREW

www.belson.com
STEP #9:
TURN THE TABLE UPRIGHT ONTO IT’S FRAME. BE SURE NOT TO SLIDE THE TABLE TOP ON ANY
ROUGH SURFACES. THIS WILL DAMAGE YOUR TABLE TOP. PLEASE TAKE CAUTION WHILE TURNING
THE TABLE OVER. AT THIS POINT IN ASSEMBLYTHE TABLE WEIGHS APPROXIMATELY 212 POUNDS.
STEP #8:
WHILE THE TABLE IS UPSIDE DOWN, FASTEN THE SEATS TO THE LARGE SPOKE ASSEMBLY AND
SEAT SUPPORT ASSEMBLIES AS SHOWN BELOW. ALIGN THE PRE-DRILLED HOLES IN THE LARGE
SPOKE ASSEMBLY AND SEAT SUPPORT ASSEMBLIES WITH THE PILOT HOLES IN THE SEATS. USE
( 1 ) ONE #12 X 2” FLAT HEAD PHILLIPS SCREW PER HOLE TO SECURE. PLEASE USE CAUTION WHILE
TIGHTENING THE SCREWS TO NOT STRIP THE THREADS OUT.
NOTE: PARTS ARE REMOVED TO SHOW DETAIL. DO NOT REMOVE FOR THIS STEP.
#12 X 2” FLAT HEAD
PHILLIPS SCREW